Part Number Hot Search : 
BZ5258 ML145050 ML0308 RF2514 AM27C010 N5231 BR351W HC4066
Product Description
Full Text Search
 

To Download BL8602 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 BL8602
BL8602 Low Power Audio Amplifier
DESCRIPTION The BL8602 is a low power audio amplifier integrated circuit intended(primarily) for telephone applications, such as in speakerphones. It provides differential speaker outputs to maximize output swing at low supply voltages(2.0 V minimum).Coupling capacitors to the speaker are not required. The gain of this amplifier is controlled easily by two external resistors. FEATURES * Wide operating supply voltage: Vcc=2V~16V * Low quiescent supply current(Icc=2.2mA,typ) * Medium output power(Po=250mW at Vcc=6V, RL=32ohm,THD10%) * Load impedance range : 8~100ohm * Mute function (Icc=55uA, typ) * Minimum number of external parts required * Low distortion BLOCK DIAGRAM
ABSOLUTE MAXIMUM RATINGS(Ta=25)
PARAMETER Supply Voltage Output Current Maximum Input,Ripple Rejection, Mute Pin Voltage Applied Output Voltage( Output Pin When Disabled) Temperature Junction SYMBOL Vcc Io Vi(max) Vo Tj VALUE -1~18 250 -1~Vcc+1 -1~Vcc+1 -55~150 UNIT V MA V V
http://www.belling.com.cn
-1-
8/15/2006
Wrote by 2006
Total 4 Pages
BL8602
PIN CONNECTIONS
PIN FUNCTION DESCRIPTION
Symbol FC1 Pin 1 Description Analog ground for amplifiers. A 1.0uF capacitor at this pin (with a 5.0uF capacitor at Pin 2) provides (typically) 52dB of power supply rejection.Turn-on time of the circuit is affected by the capacitor on this pin. This pin can be used as an alternate input. Amplifier input .The input capacitor and resistor set low frequency rolloff and input impedence. The feedback resistor is connected to this pin and Vo1. Amplifier Output#1. The dc level is (Vcc-0.7V)/2. DC supply voltage (+2.0V to +16V) is applied to this pin. Ground pin for the entire circuit Amplifier Output#2. This signal is equal in amplitude, but 180outof-phase with that at Vo1. The dc level is (Vcc-0.7V)/2. Chip Disable-Digital input. A Logic "0" (<0.8V) sets normal operation. A logic "1" (2.0V) sets the power down mode. Input impedance is nominally 90 k. A capacitor at this pin increase power supply rejection, and affects turn-on time. This pin can be left open if the capacitor at FC1 is sufficient.
Vin
2
Vo1 Vcc GND Vo2 CD
3 4 5 6 7
FC2
8
RECOMMENDED OPERATION CONDITIONS(Ta=25)
PARAMETER Supply Voltage Load Impedance Peak Load Current Differental Gain(5KHz Bandwidth) Voltage at Mute Ambient Temperature SYMBOL Vcc ZL IL(peak) Gv Vi(mute) Ta VALUE 2~16 8~100 200 0~46 0~Vcc -20~70 UNIT V mA dB V
http://www.belling.com.cn
-2-
8/15/2006
Wrote by 2006
Total 4 Pages
BL8602
ELECTRICAL CHARACTERISTICS (Vcc=6V, Ta=25,unless otherwise specified)
PARAMETER DC PARAMETER Operating Current SYMBO L Icc TEST CONDITIONS MIN TYP MAX UNI T mA mA uA V V V mV V V -200 nA K K dB
Output Voltage
Vo
Output Offset Voltage Output High Level Output Low Level Input Bias Current Equivalent Resistance AC PARAMETER Open Loop Gain of Amp 1. ( f<100Hz) Close Loop Gain of Amp 2. Output Power
Voo VOH VOL ibias REQ
Vcc=3V, Mute=0.8V Vcc=16V, Mute=0.8V Vcc=3V, Mute=2V RL=16,Rf=75K Vcc=3V Vcc=6V Vcc=12V Vcc=6V,Rf=75K,RL=32 2V2.2 2.5 55 1.0 1.20 2.8 6.10 0 Vcc1 0.16 -100 150 25
4.0 5.0 100 1.25
-30
30
100 18 80
Gvop1
Gvo2 Po
f=1KHz, RL=32 Vcc=3V, RL=16,THD 10% Vcc=6V, RL=32,THD 10% Vcc=12V, RL=100, THD10% Vcc=6V, RL=32 ,Po=125mW Vcc3V, RL=8 ,Po=20mW Vcc12V,RL=32, Po=200mW
-0.35 55 250 400
0
0.35
dB mW
Total Harmonic Distortion( f=1KHz )
THD
0.5 0.5 0.6 1.5
1.0
% % % MHz dB dB dB dB
Gain Bandwidth Product Power Supply Rejection (Vcc=6V, Vcc=3V) Muting
GBW PSRR C1=,C2=0.01uF C1=0.1uF, C2=0, f=1KHz C1=1uF, C2=5uF, f=1KHz Mute=2V, 1KHz12 52 70
Gv(mut e) Chip Disable input Voltage Low VIL High VIH
0.8 2.0
V V
http://www.belling.com.cn
-3-
8/15/2006
Wrote by 2006
Total 4 Pages
BL8602
APPLICATION CIRCUIT
http://www.belling.com.cn
-4-
8/15/2006
Wrote by 2006
Total 4 Pages


▲Up To Search▲   

 
Price & Availability of BL8602
NAC

Part # Manufacturer Description Price BuyNow  Qty.
CBL-860-200-S04
Honeywell Sensing and Control CABL SENSORMATICEAS W/INTERLOCK RFQ
0

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X