 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| INTRODUCTION This easy-to-use kit provides a platform for the evaluation of the PB51 high voltage power boosters. The PB51 is designed most commonly in combination with a small signal, general purpose op amp. However, they can also be used without a driver amplifier. This kit can be used to analyze a multitude of standard or proprietary circuit configurations. ASSEMBLY 1. On the silk screen side of the evaluation board, insert and solder the MS06 mating socket in DUT holes 1-12. Be sure each one is fully seated. 2. Solder components for your circuit. Be sure to incude proper bypassing, required compensaton components and current limit resistors. See the op amp data sheet for help in selecting these components. 3. Place the TW07 thermal washer on the heat sink over the mounting hole for the DUT. Place a #6 screw through the mounting hole and thread a #6 nut onto the screw at the back of the heat sink. Do not tighten. Note that there are two sets of mounting holes on the HS20. Holes on one edge allow room between the DUT and evaluation board for the MS06 socket. The holes on the other edge are for direct through hole mounting of the DUT to the evaluation board. It is recommended that you use the MS06. 4. Mount the DUT to the HS20 by sliding under the head of the #6 screw and on top of the thermal washer. Tighten the nut to the specified 8 to 10 in-lbs. (.9 to .13 N*M) do not over torque. 5. Install leads of the DUT into the the MS06 on the evaluation board. Use #6 self-tapping screws to secure the evaluation board to the HS20 heatsink as shown in the assembly diagram (Figure1). CAUTION PARTS LIST Part # HS20 EVAL30 MS06 TW07 Use the supplied thermal washers or thermal grease between the power amplifier and the heat sink. Description Heatsink PC Board Mating Socket Thermal Washer Quantity 1 1 1 1 package BEFORE YOU GET STARTED * All Apex amplifiers should be handled using proper ESD precautions. * Always use the heat sink and thermal washers included in this kit. * Always use adequate power supply bypassing. * Do not change connections while the circuit is powered. * Initially set all power supplies to the minimum operating levels allowed in the device data sheet. * Check for oscillations. EQUIVALENT SCHEMATIC APEX MICROTECHNOLOGY CORPORATION * TELEPHONE (520) 690-8600 * FAX (520) 888-3329 * ORDERS (520) 690-8601 * EMAIL prodlit@apexmicrotech.com 1 EK29 FIGURE 1. EVALUATION KIT FOR PB51/PB51A APEX MICROTECHNOLOGY CORPORATION * 5980 NORTH SHANNON ROAD * TUCSON, ARIZONA 85741 * USA * APPLICATIONS HOTLINE: 1 (800) 546-2739 2 EVALUATION KIT FOR PB51/PB51A EK29 FIGURE 3. PCB This data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible ORDERS (520) 690-8601 * EMAIL prodlit@apexmicrotech.com APEX MICROTECHNOLOGY CORPORATION * TELEPHONE (520) 690-8600 * FAX (520) 888-3329 * inaccuracies or omissions. All specifications are subject to change without notice. EK29U REV B OCTOBER 2004 (c) 2004 Apex Microtechnology Corp. 3 |
Price & Availability of EK29
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |