 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SNC375 Direct Drive Voice/Dual Tone Melody Controller 1 INTRODUCTION SNC375 is a 1-channel voice synthesizer and dual-tone melody IC with PWM direct drive circuit. It built-in a 4-bit tiny controller with one 4-bit input port and three 4-bit I/O ports. By programming through the tiny controller in SNC375, user's varied applications including voice section combination, dual-tone melody, key trigger arrangement, output control, and other logic functions can be easily implemented. 2 FEATURES Single power supply 2.4V - 5.5V 42 seconds voice capacity are provided (@6KHZ sample rate) Built in a 4-bit tiny controller One 4-bit input port and three 4-bit I/O ports are provided 128*4 bits RAM are provided 132K*10 ROM size are provided for voice data and program Maximum 16k program ROM is provided Readable ROM code data IR carrier signal is provided Built in a high quality speech synthesizer Adaptive playing speed from 2.5k-20kHz is provided One voice channel plus Dual-Tone Melody Built in a PWM Direct Drive circuit and a fixed current D/A output System clock: 2MHz Low Power Reset Ver: 1.3 1 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller 3 Block Diagram ROM Program/Speech 132Kx10 bits Address Pointers/ STACK SRAM (128 nibbles) Timer ALU IO1 IO2 Sampling Rate Counter Timing Generator Dual-Tone Generator OSC PWM D/A IO6 Voice Synthesizer IO3 4 PIN ASSIGNMENT Symbol P13 ~ P10 P23 ~ P20 P33 ~ P30 P63 ~ P60 VDD GND RST OSC BUO1/VO BUO2 I/O I I/O I/O I/O P P I O O O Function Description Bit3 ~ Bit0 of Input port 1 Bit3 ~ Bit0 of I/O port 2 Bit3 ~ Bit0 of I/O port 3 Bit3 ~ Bit0 of I/O port 6 Positive power supply Negative power supply Reset pin (active high) Oscillator / Crystal Out Positive Output of PWM or DA output Negative Output of PWM Ver: 1.3 2 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller 5 FUNCTION DESCRIPTIONS 5.1. Oscillator SNC375 accept RC type oscillator for system clock. The typical circuit diagram for oscillator is listed as follow. VCC RC Oscillator 5.2. ROM SNC375 contains substantial 132K words (10-bit) internal ROM. Program, voices and other data are shared with this same 132K words ROM. 5.3. RAM SNC375 contains 128 nibbles RAM. The 128 nibbles RAM are divided into eight pages (page 0 to page 7, 16 nibbles RAM on each page). In our programming structure, users can easily define and locate RAM page in the program. For instance, users can use the instructions, PAGEn (n=0 to 7) to switch and indicate the RAM page. Besides, users can use direct mode, M0 ~ M15 in the data transfer type instructions, to access all 16 nibbles of each page. 5.4. Power Down Mode "End" instruction will power down SNC375 and enable IC to consume fewer current for power saving. (<3uA @VDD=3V and <5uA @VDD=5V) Please be aware that when the power down mode is activated in SNC375, any valid data transition (L H or H L) occurring on any input port (P1) or IO ports (P2, P3 and P6) will lead SNC375 back to normal operation mode. 5.5. Sampling Rate Counter The unique sampling rate counter is designed in voice channel to be able to play diverse voices at different sample playing rates. The playing rate can be adaptively set up among from the wide ranges of 2.5KHz to 20KHz. This feature makes voice close to its original source and yield the better voice quality. Ver: 1.3 3 r August 26, 2003 OSC SNC375 Direct Drive Voice/Dual Tone Melody Controller 5.6. Dual-Tone Generator A dual-tone melody generator is included to generate 2-channel music songs with a pleasant square-wave-like timbre. The pitch range of each tone generator is as wide as 4 octaves (48 different notes totally). The output of dual-tone generator can be mixed with the output of voice synthesizer to achieve voice playing with BGM (background music). Additionally, Sonix provides a numbered-musical-notation representation to help users compose their songs. Further, a MIDI (1.0) file translator can convert MIDI files into Sonix format. 5.7. I/O Ports P1 is a 4-bit input port and P2/P3/P6 are three 4-bit I/O ports. Any bit of P2, P3 and P6 can be programmed as either input or output port individually. Any valid data transition (H L or L H) of P1, P2, P3 and P6 can reactivate the chip when the chip is in power-down mode. To Internal Data Bus PAD Read Control Weak Input Port Configuration (P10~P13) Port Data PAD Port Status Weak To Internal Data Bus Read Control I/O Port Configuration (P20~P23, P30~P33, P60~P63) Note: weak N-MOS's can serve as pull-low resistor. 4 Ver: 1.3 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller 5.8. IR Function P33 can be modulated with 38.5KHz square wave before sent out to P33 pin. The IR signal can be achieved by this modulated signal. 38.5KHZ "1" PAD Mode P33 5.9. DAC & PWM SNC375 is an advanced chip to be designed having two optimal methods to play out the voices. One is DAC and the other is PWM. Upon user's applications, user can select either DAC or PWM in his design. Please be aware that only one method can be activated at a time. DAC: A 7-bit current type digital-to-analog converter is built-in SNC375. The relationship between input digital data and output analog current signal is listed in the following table. Also, the recommended application circuit is illustrated as follows. Input data 0 1 ... N ... 127 Typical value of output current (mA) 0 3/127 n*(3/127) 3 Ver: 1.3 5 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller VCC BUO1/VO 1K DAC output PWM: A PWM (pulse width modulation) circuit is built-in SNC375. PWM can convert input digital data into pulse trains with suitable different pulse width. The maximum resolution of PWM is 7 bits. Two huge output stage circuits are designed in SNC375. With this advanced circuit, the chip is capable of driving speaker directly without external transistors. The recommended application circuit is illustrated as follows. BUO1/VO BUO2 PWM Output Ver: 1.3 6 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller 6 ABSOLUTE MAXIMUM RATING Items Supply Voltage Input Voltage Operating Temperature Storage Temperature Symbol VDD-V VIN TOP TSTG Min -0.3 VSS-0.3 0 -55.0 Max 6.0 VDD+0.3 55.0 125.0 Unit. V V o C o C 7 ELECTRICAL CHARACTERISTICS Item Operating Voltage Standby current Operating Current Input current of P1, P2, P3, P6 Drive current of P2, P3, P6 Sink Current of P2, P3, P6 Drive current of P2, P3, P6 Sink Current of P2, P3, P6 Drive current of Buo1 Sink Current of Buo1 Drive Current of Buo2 Sink Current of Buo2 Oscillation Freq. IR Carrier Frequency Sym. Min. Typ. Max. Unit Condition VDD 2.4 3.0 5.5 V ISBY 2.0 uA VDD=3V , no load 5.0 VDD=4.5V, no load IOPR 300 uA VDD=3V , no load 700 VDD=4.5V, no load IIH 3.0 10.0 uA VDD=3V,VIN=3V IOD IOS IOD IOS IOD IOS IOD IOS FOSC Fir 100 100 100 100 4 6 5 9 120 120 120 120 2.0 38.5 mA VDD=3V,VO=2.4V mA VDD=3V,VO=0.4V mA VDD=4.5V,VO=3.9V mA VDD=4.5V,VO=0.4V mA VDD=3V,Buo1=1.5V mA VDD=3V,Buo1=1.5V mA mA MHz KHz VDD=3V,Buo2=1.5V VDD=3V,Buo2=1.5V VDD=3V Fosc=2MHz Ver: 1.3 7 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller 8 ROSC Performance ROSC frequency vs VDD (Typical value, R=120K) 3 ROSC (MHz) 2.5 120k 2 1.5 2 3 4.5 5.5 VDD (Voltage) ROSC frequency vs. VDD (For various R) 3 ROSC (MHz) 2.5 100k 110k 120k 130k 150k 2 1.5 2 3 4.5 5.5 VDD (Voltage) Ver: 1.3 8 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller 9 APPLICATION CIRCUIT D/A Speaker Output 16 Scan Keys C1 8050 1K VDD VDD VDD C2 R 0.1uF 0.1u F VO 1 P 33 P 32 P 31 P 30 VDD OS C RS T Note: The C1 (0.1uF) between Power and GND should be closed to VDD pin of SNC375 as possible. G ND P 23 P 22 P 21 P 20 P 13 S NC375 P 10 P 12 TR4 TR8 TR12 TR16 P 11 TR3 TR7 TR11 TR15 TR2 TR6 TR10 TR14 TR1 TR5 TR 9 TR13 Ver: 1.3 9 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller 10 BONDING PAD 23 22 21 20 19 18 17 16 15 (0.00,0.00) 14 13 12 11 10 9 8 7 P63 P62 P61 P60 P33 P32 P31 P30 P23 P22 P21 P20 P13 P12 P11 P10 RST 1 OSC 2 GND 3 BUO1 4 VDD 5 BUO2 6 GND SNC375 Note: The substrate MUST be connected to Vss in PCB layout. Ver: 1.3 10 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller DISCLAIMER The information appearing in SONiX web pages ("this publication") is believed to be accurate. However, this publication could contain technical inaccuracies or typographical errors. The reader should not assume that this publication is error-free or that it will be suitable for any particular purpose. SONiX makes no warranty, express, statutory implied or by description in this publication or other documents which are referenced by or linked to this publication. In no event shall SONiX be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever, including, without limitation, those resulting from loss of use, data or profits, whether or not advised of the possibility of damage, and on any theory of liability, arising out of or in connection with the use or performance of this publication or other documents which are referenced by or linked to this publication. This publication was developed for products offered in Taiwan. SONiX may not offer the products discussed in this document in other countries. Information is subject to change without notice. Please contact SONiX or its local representative for information on offerings available. Integrated circuits sold by SONiX are covered by the warranty and patent indemnification provisions stipulated in the terms of sale only. The application circuits illustrated in this document are for reference purposes only. SONIX DISCLAIMS ALL WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE. SONIX reserves the right to halt production or alter the specifications and prices, and discontinue marketing the Products listed at any time without notice. Accordingly, the reader is cautioned to verify that the data sheets and other information in this publication are current before placing orders. Products described herein are intended for use in normal commercial applications. Applications involving unusual environmental or reliability requirements, e.g. military equipment or medical life support equipment, are specifically not recommended without additional processing by SONIX for such application. Ver: 1.3 11 August 26, 2003 SNC375 Direct Drive Voice/Dual Tone Melody Controller GREEN VOICE Ver: 1.3 12 August 26, 2003 |
Price & Availability of SNC375
 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |
