 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TECHNICAL DATA 2 x 1 W portable/mains-fed stereo power amplifier The KKA7053N is an integrated class-B stereo power amplifier in a 16-lead dual-in-line (DIL) plastic package. The device, consisting of two BTL amplifiers, is primarily developed for portable audio applications but may also be used in mains-fed applications. * * * * * No external components No switch-ON/OFF clicks Good overall stability Low power consumption Short-circuit-proof 16 1 KKA7053N N SUFFIX PLASTIC DI ORDERING INFORMATION KKA7053N Plastic DIP QUICK REFERENCE DATA PARAMETER Supply voltage range Total quiescent current Output power Internal voltage gain Total harmonic distortion TA = to 150 C CONDITIONS SYMBOL VP Itot PO Gv THD MIN. 3 38 - MAX. 18 16 1 40 1.0 UNIT V mA W dB % RL = RL = 8 , VP = 6 V, THD = 10% RL = 8 , VP = 6 V PO = 0.1 W, RL = 8 , VP = 6 V PINNING Pin 01 02 03 04 05 06 07 08 Symbol SGND1 IN1 n.c. n.c. VP IN2 SGND2 n.c. Description signal ground 1 input 1 not connected not connected supply voltage input 2 signal ground 2 not connected Pin 09 10 11 12 13 14 15 16 Symbol OUT2A GND2 n.c. OUT2B OUT1B GND1 n.c. OUT1A Description output 2 (positive) power ground 2 not connected output 2 (negative) output 1 (negative) power ground 1 not connected output 1 (positive) Note The information contained within the parentheses refer to the polarity of the loudspeaker terminal to which the output must be connected. FUNCTIONAL DESCRIPTION The KKA7053N is a stereo output amplifier, with an internal gain of 39 dB, which is primarily for use in portable audio applications but may also be used in mains-fed applications. The current trends in portable audio application design is to reduce the number of batteries which results in a reduction of output power when using conventional output stages. The KKA7053N overcomes this problem by using the Bridge-Tied-Load (BTL) principle and is capable of delivering 1.2 W into an 8 load (V P = 6 V). The load can be short-circuited under all input conditions. 1 KKA7053N +Vp 01 0,1 F KKA7053N 16 + _ 220 F + RL 1 Input 1 02 G N DS 01 13 - Input 2 06 12 RL 2 DC Volume 07 09 + 10 14 03 04 08 11 15 GND-P GND-P 1. 2. 3. This capacitor can be omitted if the 220 F electrolytic capacitor is connected close to pin 01. RL= 8 Resistors R1, R2 = 5,6 k connected to the inputs 02, 06 should be dual. Fig.1 Block diagram, test and application circuit diagram 2 KKA7053N RATINGS Limiting values in accordance with the Absolute Maximum System PARAMETER Supply voltage Non-repetitive peak output current Total power dissipation Crystal temperature Storage temperature range THERMAL RESISTANCE From junction to ambient CONDITIONS SYMBOL VP IOSM Ptot Tc Tstg -60 MIN. see Fig.2 +150 +150 C C MAX. 18 1.5 UNIT V A Rth j-a 60 K/W Power dissipation Assuming: VP = 6 V and RL = 8 : The maximum sinewave dissipation is 1.8 W, therefore Tamb(max.) = 150 - (60 x 1.8) = 42C. Fig.2 Power derating curve 3 KKA7053N CHARACTERISTICS VP = 6 V; RL = 8 W; Tamb = 25C; unless otherwise specified; measured from test circuit, Fig.2. PARAMETER Supply voltage range Total quiescent current Input bias current Supply voltage ripple rejection Input impedance DC output offset voltage Noise output voltage (RMS value) Output power Total harmonic distortion Internal voltage gain Channel balance Channel separation Frequency response note 3 RL = 8 , VP = 6 V note 3 note 4 note 5 THD = 10% PO = 0.1 W note 2 RL = ; note 1 CONDITIONS SYMBOL VP Itot Ibias SVRR ZI V13-16 V12-9 Vno(rms) Vno(rms) PO THD GV GV f 38 40 MIN. 3 40 MAX. 18 16 300 100 100 300 60 (type) 0.8 1.0 40 1 100 (type) UNIT V mA nA dB k mV mV V V W % dB dB dB kHz 0.2 to 20 (type) Notes to the characteristics 1. With a practical load the total quiescent current depends on the offset voltage. 2. Ripple rejection measured at the output with RS = 0 and f = 100 Hz to 10 kHz. The ripple voltage (200 mV) is applied to the positive supply rail. 3. RS = 5 k. 4. The noise output voltage (RMS value) is measured with RS = 5 k, unweighted and a bandwidth of 60 Hz to 15 kHz. 5. The noise output voltage (RMS value) is measured with RS = 0 and f = 500 kHz with 5 kHz bandwidth. If RL = 8 and LL = 200 mH the noise output current is only 100 nA. 4 KKA7053N 5 KKA7053N N SUFFIX PLASTIC DIP (MS - 001BB) A Dimension, mm 16 9 B 1 8 Symbol A B C MIN 18.67 6.1 MAX 19.69 7.11 5.33 F L D F 0.36 1.14 2.54 7.62 0 2.92 7.62 0.2 0.38 0.56 1.78 C -T- SEATING N G D 0.25 (0.010) M T K PLANE G H H J M J K L M N 10 3.81 8.26 0.36 NOTES: 1. Dimensions "A", "B" do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. 6 |
Price & Availability of KKA7053N
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |