BGF119 transient voltage suppressor data sheet, v3.0, november 2008 small signal discretes
edition 2008-11-18 published by infineon technologies ag 81726 mnchen, germany ? infineon technologies ag 2008. all rights reserved. legal disclaimer the information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (?beschaffenheitsgarantie?). with respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, infineon technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. information for further information on technology, delivery terms and conditions and prices please contact your nearest infineon technologies office ( www.infineon.com ). warnings due to technical requirements components may contain dangerous substances. for information on the types in question please contact your nearest infineon technologies office. infineon technologies components may only be used in life-support devices or systems with the express written approval of infineon technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. if they fail, it is reasonable to assume that the health of the user or other persons may be endangered.
BGF119 data sheet 3 v3.0, 2008-11-18 BGF119 revision history: 2008-11-18, v3.0 previous version: 2008-10-20, v2.0 page subjects (major changes since last revision) 6 updated figure 3 all target status removed
data sheet 4 v3.0, 2008-11-18 BGF119 transient voltage suppressor transient voltage suppressor description the BGF119 is a single line tvs diode designed for transient voltage and power overstress suppression. all pins are protected against esd pulses of 15kv contact discharge according to iec61000-4-2. the wafer level package is a green package with a size of only 0.75 mm x 0.75 mm and a total height of 0.60 mm. features ? 1 channel tvs diode designed for portable application ? esd protection according to iec61000-4-2 for +/-15 kv contact discharge on all ios ? wafer level package with snagcu solder balls ? rohs and weee compliant package ? very small form factor tvs ? high peak pulse power ? stand-off voltage up to 8 v ? low clamping voltage factor vcl/vbr ? fast response time type package marking chip BGF119 wlp-4-1 BGF119 n0742 wlp-4-1-3d
BGF119 transient voltage suppressor data sheet 5 v3.0, 2008-11-18 figure 1 schematic table 1 maximum ratings parameter symbol values unit note / test condition min. typ. max. voltage at all pins to gnd v p 0 8 v operating temperature range t op -30 +85 c storage temperature range t stg -55 +150 c electrostatic discharge according to iec61000- 4-2 1) at all pins 1) contact discharge v esd -15 15 kv table 2 electrical characteristics 1) 1) otherwise specified at t a = 25 c parameter symbol values unit note / test condition min. typ. max. line capacitance to gnd c t 230 pf v r = 0 v forward voltage v f 2) 2) to avoid high temperature and possible disassembling of component from the board, dc current operation to be limited to few seconds 1.1 v i f = 850 ma break down voltage v br 10 10 11 12 12 v i r = 15 ma t a = -30c t a = 25c t a = 85c clamping voltage during transient v cl 3) 3) 8/20 s pulse waveform according to iec61000-4-5 13 v i r = 1 a leakage current of line to gnd i r 1 10 100 800 na v r = 8 v t a = -30c t a = 25c t a = 85c b1 (gnd) a1 a2 b2 (gnd)
data sheet 6 v3.0, 2008-11-18 BGF119 transient voltage suppressor figure 2 line capacitance versus reverse voltage (typical values) at 25c figure 3 peak pulse reverse current (iec61000-4-5) versus clamping voltage (typical values) at 25c line capacitance BGF119 0 50 100 150 200 250 300 0123456 voltage [v] line capacitance [pf] BGF119 peak pulse current vs clamping voltage 0,1 1,0 10,0 100,0 10 12 14 16 18 20 clamping voltage v cl [v] reverse current i r [a]
BGF119 transient voltage suppressor data sheet 7 v3.0, 2008-11-18 package outline figure 4 package wlp-4-1 tape and reel specification figure 5 tape for wlp-4-1 a2 a1 b2 b1 0.05 standoff 0.2 0.1 c 0.05 0.6 coplanarity 4x 0.08 c seating plane c 3) 0.4 b 0.75 0.05 0.4 0.05 a 0.75 0.25 1) 0.04 ?0.05 4x m b a 1) dimension is measured at the maximum solder ball diameter, parallel to primary datum c 3) primary datum c and seating plane are defined by the domed crowns of the balls 2) a1 corner identified by marking wlp-4-1-po-n v02 (0.175 ) 0.05 (0.175 ) 0.05 (0.175 ) 0.05 (0.175 ) 0.05 pin a1 corner index area 2) wlp-4-1-tp v01 pin 1 corner index area 8 0.1 0.85 0.05 0.85 0.05 0.25 0.65 0.1 4
|
