www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 1 of 9 spec no : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no ? HDF1575A smd-6 marking ? ? hdf6g09 prepared ? checked ? approved ? d a t e ? 2006-5-11 ??? shoulder electronics limited ?? customer received: checked ? approved date
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 2 of 9 ?? history record date spec. no. ?? part no. ??? customer no. modify content ? remark
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 3 of 9 1.features gps applications usable bandwidth of 2 mhz no impedance matching require for operation at 50 . single-ended operation 2.package dimension marking hdf6g09 hd: brand f : filter 6 : smd-6 g09: no.
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 4 of 9 3. marking 2.1 color: black or blue 2.2 1575: center frequency(mhz) 4.performance 4.1application low-loss saw filter of cordless system. center frequency:1575.42 mhz 4.2maximum rating operation temperature range -40 to +85 storage temperature range -40 to +85 power handling capability 10dbm 4.3electronic characteristics
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 5 of 9 parameter symbol conditions min typ. max. unit center frequency 1575.42 mhz operational bandwidth f op 1574.22 1576.62 mhz insertion loss il in f op 1.5 2.5 db amplitude variation av in f op 0.2 0.5 db vswer swr in f op 1.3 2 rejectiona wrt 0 db rj1 0.3 ~ 700 mhz 40 45 db in top rj2 700~1460mhz 37 40.5 db rj3 1460~1470mhz 45 50 db rj4 1470~1525mhz 37 43 db rj5 1525~1535.42mh z 20 25 db rj6 1615.42~1620mh z 25 35 db rj7 1620~1650 mhz 45 50 db rj8 1650~3000 mhz 40 45 db i/p & o/p impedance zin/zout u nmatched 50 ohm notes : 1) all specifications are based on the matching schematic shown belo w, measured by agilent network analyzer and full 2 port calibration. 2) electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 3) all attenuation measurements are measured relative to insertion loss 4.4 test circuit
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 6 of 9 5. environmental characteristics 5-1 temperature cycling subject the device to a low temperature of -40 for 30 minutes. following by a high temperature of +85 for 5 minutes and a higher temperature of +85 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the measurement. it shall meet the specifications in 4.3. 5-2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 4.3. 5-3 solderability submerge the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be cove red with new solder. it shall meet the specifications in 4.3. 5-4 mechanical shock drop the device randomly onto the c oncrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 4.3. 5-5 vibration subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter sh all fulfill the specifications in 4.3. 6. remark 6.1 static voltage static voltage between signal load & gr ound may cause deterior ation &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause deteri oration & destruction of the component. please avoid ultrasonic cleaning 6.3 soldering only leads of component may be solder ed. please avoid soldering another part of component.
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 7 of 9 7. packing 7.1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during trans portation and storage. 7.2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7.3 taping structure (1) the tape shall be wound around th e reel in the direction shown below. (2) label device name user product name quantity lot no. (3) leader part and vaca nt position specifications.
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 8 of 9 8. tape specifications 8.1 tensile strength of ca rrier tape: 4.4n/mm width 8.2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 4.00 0.10 2.00 0.10 ?1.50 ?1.5 0.25 0.31 0.05 1.30 0.10 3.4 max. 3.4 max [figure 2]
saw filter HDF1575A s-6 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 9 of 9 [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
