![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
mc68hc08jl3/h rev. 4 mc68hc08jk1 mc68hrc08jk1 mc68hc08jk3 mc68hrc08jk3 mc68hc08jl3 mc68hrc08jl3 hcmos microcontroller unit technical data
mc68h(r)c08jl3 ? rev. 4 technical data motorola list of sections 3 technical data ?mc68h(r)c08jl3 list of sections section 1. general description . . . . . . . . . . . . . . . . . . . .21 section 2. memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 section 3. random-access memory (ram) . . . . . . . . . .37 section 4. read-only memory (rom) . . . . . . . . . . . . . . .39 section 5. configuration register (config) . . . . . . . . .41 section 6. central processor unit (cpu) . . . . . . . . . . . .45 section 7. system integration module (sim) . . . . . . . . .65 section 8. oscillator (osc) . . . . . . . . . . . . . . . . . . . . . . .89 section 9. monitor rom (mon) . . . . . . . . . . . . . . . . . . . .95 section 10. timer interface module (tim) . . . . . . . . . . .105 section 11. analog-to-digital converter (adc) . . . . . .127 section 12. i/o ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 section 13. external interrupt (irq) . . . . . . . . . . . . . . .149 section 14. keyboard interrupt module (kbi). . . . . . . .155 section 15. computer operating properly (cop) . . . .163 section 16. low voltage inhibit (lvi) . . . . . . . . . . . . . .169 section 17. break module (break) . . . . . . . . . . . . . . .173 section 18. electrical specifications . . . . . . . . . . . . . . .181 section 19. mechanical specifications . . . . . . . . . . . . .193 list of sections technical data mc68h(r)c08jl3 ? rev. 4 4 list of sections motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola table of contents 5 technical data ?mc68h(r)c08jl3 table of contents section 1. general description 1.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 1.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 1.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 1.4 mcu block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 1.5 pin assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 1.6 pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 section 2. memory 2.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3 i/o section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.4 monitor rom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 section 3. random-access memory (ram) 3.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 3.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 3.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 section 4. read-only memory (rom) 4.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 table of contents technical data mc68h(r)c08jl3 ? rev. 4 6 table of contents motorola section 5. configuration register (config) 5.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 section 6. central processor unit (cpu) 6.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.4 cpu registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.4.1 accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.4.2 index register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.4.3 stack pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.4.4 program counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.4.5 condition code register . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.5 arithmetic/logic unit (alu) . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.7 cpu during break interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.8 instruction set summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.9 opcode map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 section 7. system integration module (sim) 7.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 7.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 7.3 sim bus clock control and generation . . . . . . . . . . . . . . . . . . 69 7.3.1 bus timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 7.3.2 clock start-up from por . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 7.3.3 clocks in stop mode and wait mode . . . . . . . . . . . . . . . . . . 69 table of contents mc68h(r)c08jl3 ? rev. 4 technical data motorola table of contents 7 7.4 reset and system initialization. . . . . . . . . . . . . . . . . . . . . . . . . 70 7.4.1 external pin reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 7.4.2 active resets from internal sources . . . . . . . . . . . . . . . . . . 71 7.4.2.1 power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 7.4.2.2 computer operating properly (cop) reset . . . . . . . . . . 73 7.4.2.3 illegal opcode reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 7.4.2.4 illegal address reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 7.4.2.5 lvi reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 7.5 sim counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 7.5.1 sim counter during power-on reset . . . . . . . . . . . . . . . . . 74 7.5.2 sim counter during stop mode recovery . . . . . . . . . . . . . . 74 7.5.3 sim counter and reset states. . . . . . . . . . . . . . . . . . . . . . . 75 7.6 exception control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 7.6.1 interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 7.6.1.1 hardware interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 7.6.1.2 swi instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 7.6.2 interrupt status registers. . . . . . . . . . . . . . . . . . . . . . . . . . . 79 7.6.2.1 interrupt status register 1 . . . . . . . . . . . . . . . . . . . . . . . 80 7.6.2.2 interrupt status register 2 . . . . . . . . . . . . . . . . . . . . . . . . 80 7.6.2.3 interrupt status register 3 . . . . . . . . . . . . . . . . . . . . . . . . 81 7.6.3 reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 7.6.4 break interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 7.6.5 status flag protection in break mode . . . . . . . . . . . . . . . . . 81 7.7 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 7.7.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 7.7.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 7.8 sim registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 7.8.1 break status register (bsr) . . . . . . . . . . . . . . . . . . . . . . . . 85 7.8.2 reset status register (rsr) . . . . . . . . . . . . . . . . . . . . . . . . 86 7.8.3 break flag control register (bfcr) . . . . . . . . . . . . . . . . . . 88 section 8. oscillator (osc) 8.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 8.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 table of contents technical data mc68h(r)c08jl3 ? rev. 4 8 table of contents motorola 8.3 x-tal oscillator (mc68hc08xxx). . . . . . . . . . . . . . . . . . . . . . . . 90 8.4 rc oscillator (mc68hrc08xxx) . . . . . . . . . . . . . . . . . . . . . . . 91 8.5 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 8.5.1 crystal amplifier input pin (osc1). . . . . . . . . . . . . . . . . . . . 92 8.5.2 crystal amplifier output pin (osc2/pta6/rcclk). . . . . . . 92 8.5.3 oscillator enable signal (simoscen). . . . . . . . . . . . . . . . . 92 8.5.4 x-tal oscillator clock (xtalclk). . . . . . . . . . . . . . . . . . . . . 92 8.5.5 rc oscillator clock (rcclk). . . . . . . . . . . . . . . . . . . . . . . . 93 8.5.6 oscillator out 2 (2oscout) . . . . . . . . . . . . . . . . . . . . . . . . 93 8.5.7 oscillator out (oscout). . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.6 low power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.7 oscillator during break mode. . . . . . . . . . . . . . . . . . . . . . . . . . 94 section 9. monitor rom (mon) 9.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 9.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 9.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 9.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 9.4.1 entering monitor mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 9.4.2 baud rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9.4.3 data format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9.4.4 echoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9.4.5 break signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 9.4.6 commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 section 10. timer interface module (tim) 10.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 10.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 10.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 10.4 pin name conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 table of contents mc68h(r)c08jl3 ? rev. 4 technical data motorola table of contents 9 10.5 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 10.5.1 tim counter prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 10.5.2 input capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 10.5.3 output compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 10.5.3.1 unbuffered output compare . . . . . . . . . . . . . . . . . . . . . 110 10.5.3.2 buffered output compare . . . . . . . . . . . . . . . . . . . . . . . 110 10.5.4 pulse width modulation (pwm) . . . . . . . . . . . . . . . . . . . . . 111 10.5.4.1 unbuffered pwm signal generation . . . . . . . . . . . . . . . 112 10.5.4.2 buffered pwm signal generation . . . . . . . . . . . . . . . . . 113 10.5.4.3 pwm initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 10.6 interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 10.7 wait mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 10.8 tim during break interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 116 10.9 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 10.10 i/o registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 10.10.1 tim status and control register (tsc) . . . . . . . . . . . . . . . 117 10.10.2 tim counter registers (tcnth:tcntl) . . . . . . . . . . . . . . 119 10.10.3 tim counter modulo registers (tmodh:tmodl) . . . . . . 120 10.10.4 tim channel status and control registers (tsc0:tsc1) . 121 10.10.5 tim channel registers (tch0h/l:tch1h/l) . . . . . . . . . . 125 section 11. analog-to-digital converter (adc) 11.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 11.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 11.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 11.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 11.4.1 adc port i/o pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 11.4.2 voltage conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 11.4.3 conversion time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 11.4.4 continuous conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 11.4.5 accuracy and precision . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.5 interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 table of contents technical data mc68h(r)c08jl3 ? rev. 4 10 table of contents motorola 11.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.7 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.7.1 adc voltage in (adcvin) . . . . . . . . . . . . . . . . . . . . . . . . . 132 11.8 i/o registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 11.8.1 adc status and control register. . . . . . . . . . . . . . . . . . . . 132 11.8.2 adc data register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 11.8.3 adc input clock register . . . . . . . . . . . . . . . . . . . . . . . . . 135 section 12. i/o ports 12.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 12.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 12.3 port a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 12.3.1 port a data register (pta) . . . . . . . . . . . . . . . . . . . . . . . . 139 12.3.2 data direction register a (ddra) . . . . . . . . . . . . . . . . . . . 140 12.3.3 port a input pull-up enable register (ptapue) . . . . . . . . 141 12.4 port b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.4.1 port b data register (ptb) . . . . . . . . . . . . . . . . . . . . . . . . 143 12.4.2 data direction register b (ddrb) . . . . . . . . . . . . . . . . . . . 143 12.5 port d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12.5.1 port d data register (ptd) . . . . . . . . . . . . . . . . . . . . . . . . 145 12.5.2 data direction register d (ddrd). . . . . . . . . . . . . . . . . . . 146 12.5.3 port d control register (pdcr). . . . . . . . . . . . . . . . . . . . . 147 section 13. external interrupt (irq) 13.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 13.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 13.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 13.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 13.4.1 irq1 pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 13.5 irq module during break interrupts . . . . . . . . . . . . . . . . . . . 153 13.6 irq status and control register (iscr) . . . . . . . . . . . . . . . . 153 table of contents mc68h(r)c08jl3 ? rev. 4 technical data motorola table of contents 11 section 14. keyboard interrupt module (kbi) 14.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 14.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 14.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 14.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 14.4.1 keyboard initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 14.4.2 keyboard status and control register. . . . . . . . . . . . . . . . 159 14.4.3 keyboard interrupt enable register . . . . . . . . . . . . . . . . . . 160 14.5 wait mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 14.6 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 14.7 keyboard module during break interrupts . . . . . . . . . . . . . . . 161 section 15. computer operating properly (cop) 15.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 15.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 15.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 15.4 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.1 2oscout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.2 copctl write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.3 power-on reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.4 internal reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.5 reset vector fetch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 15.4.6 copd (cop disable). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 15.4.7 coprs (cop rate select) . . . . . . . . . . . . . . . . . . . . . . . . 166 15.5 cop control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.6 interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.7 monitor mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.8 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.8.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.8.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 15.9 cop module during break mode . . . . . . . . . . . . . . . . . . . . . . 168 table of contents technical data mc68h(r)c08jl3 ? rev. 4 12 table of contents motorola section 16. low voltage inhibit (lvi) 16.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 16.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 16.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 16.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 16.5 lvi control register (config2/config1) . . . . . . . . . . . . . . 170 16.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 16.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 16.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 section 17. break module (break) 17.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 17.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 17.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 17.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 17.4.1 flag protection during break interrupts . . . . . . . . . . . . . . . 176 17.4.2 cpu during break interrupts . . . . . . . . . . . . . . . . . . . . . . . 176 17.4.3 tim during break interrupts . . . . . . . . . . . . . . . . . . . . . . . . 176 17.4.4 cop during break interrupts . . . . . . . . . . . . . . . . . . . . . . . 176 17.5 break module registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 17.5.1 break status and control register (brkscr) . . . . . . . . . 177 17.5.2 break address registers . . . . . . . . . . . . . . . . . . . . . . . . . . 178 17.5.3 break status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 17.5.4 break flag control register (bfcr) . . . . . . . . . . . . . . . . . 180 17.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 17.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 17.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 section 18. electrical specifications 18.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 18.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 table of contents mc68h(r)c08jl3 ? rev. 4 technical data motorola table of contents 13 18.3 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 182 18.4 functional operating range. . . . . . . . . . . . . . . . . . . . . . . . . . 183 18.5 thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 18.6 5v dc electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . 184 18.7 5v control timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 18.8 5v oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 186 18.9 3v dc electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . 187 18.10 3v control timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 18.11 3v oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 189 18.12 typical supply currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 18.13 adc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 section 19. mechanical specifications 19.1 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 19.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 19.3 20-pin pdip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 19.4 20-pin soic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 19.5 28-pin pdip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 19.6 28-pin soic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 table of contents technical data mc68h(r)c08jl3 ? rev. 4 14 table of contents motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola list of figures 15 technical data ?mc68h(r)c08jl3 list of figures figure title page 1-1 mcu block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 1-2 mcu pin assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2-1 memory map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2-2 control, status, and data registers . . . . . . . . . . . . . . . . . . . . . 30 5-1 configuration register 2 (config2) . . . . . . . . . . . . . . . . . . . . 42 5-2 configuration register 1 (config1) . . . . . . . . . . . . . . . . . . . . 43 6-1 cpu registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6-2 accumulator (a) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6-3 index register (h:x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6-4 stack pointer (sp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6-5 program counter (pc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6-6 condition code register (ccr) . . . . . . . . . . . . . . . . . . . . . . . . 50 7-1 sim block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 7-2 sim i/o register summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 7-3 sim clock signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 7-4 external reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 7-5 internal reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 7-6 sources of internal reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 7-7 por recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 7-8 interrupt processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 7-9 interrupt entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 7-10 interrupt recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 7-11 interrupt recognition example . . . . . . . . . . . . . . . . . . . . . . . . . 78 7-12 interrupt status register 1 (int1). . . . . . . . . . . . . . . . . . . . . . . 80 7-13 interrupt status register 2 (int2). . . . . . . . . . . . . . . . . . . . . . . 80 7-14 interrupt status register 3 (int3). . . . . . . . . . . . . . . . . . . . . . . 81 list of figures technical data mc68h(r)c08jl3 ? rev. 4 16 list of figures motorola figure title page 7-15 wait mode entry timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 7-16 wait recovery from interrupt or break . . . . . . . . . . . . . . . . . . . 83 7-17 wait recovery from internal reset. . . . . . . . . . . . . . . . . . . . . . 83 7-18 stop mode entry timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 7-19 stop mode recovery from interrupt or break . . . . . . . . . . . . . . 85 7-20 break status register (bsr) . . . . . . . . . . . . . . . . . . . . . . . . . . 85 7-21 reset status register (rsr) . . . . . . . . . . . . . . . . . . . . . . . . . . 87 7-22 break flag control register (bfcr) . . . . . . . . . . . . . . . . . . . . 88 8-1 x-tal oscillator external connections . . . . . . . . . . . . . . . . . . . . 90 8-2 rc oscillator external connections . . . . . . . . . . . . . . . . . . . . . 91 9-1 monitor mode circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 9-2 monitor data format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9-3 sample monitor waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9-4 read transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 9-5 break transaction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 10-1 tim block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 10-2 tim i/o register summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 10-3 pwm period and pulse width . . . . . . . . . . . . . . . . . . . . . . . . 112 10-4 tim status and control register (tsc) . . . . . . . . . . . . . . . . . 117 10-5 tim counter registers (tcnth:tcntl) . . . . . . . . . . . . . . . . 120 10-6 tim counter modulo registers (tmodh:tmodl). . . . . . . . . 121 10-7 tim channel status and control registers (tsc0:tsc1) . . . 122 10-8 chxmax latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 10-9 tim channel registers (tch0h/l:tch1h/l). . . . . . . . . . . . . 126 11-1 adc i/o register summary . . . . . . . . . . . . . . . . . . . . . . . . . . 128 11-2 adc block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 11-3 adc status and control register (adscr) . . . . . . . . . . . . . . 132 11-4 adc data register (adr) . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 11-5 adc input clock register (adiclk) . . . . . . . . . . . . . . . . . . . 135 12-1 i/o port register summary. . . . . . . . . . . . . . . . . . . . . . . . . . . 138 12-2 port a data register (pta) . . . . . . . . . . . . . . . . . . . . . . . . . . 139 12-3 data direction register a (ddra) . . . . . . . . . . . . . . . . . . . . . 140 list of figures mc68h(r)c08jl3 ? rev. 4 technical data motorola list of figures 17 figure title page 12-4 port a i/o circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 12-5 port a input pull-up enable register (ptapue) . . . . . . . . . . 142 12-6 port b data register (ptb) . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12-7 data direction register b (ddrb) . . . . . . . . . . . . . . . . . . . . . 143 12-8 port b i/o circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 12-9 port d data register (ptd) . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12-10 data direction register d (ddrd) . . . . . . . . . . . . . . . . . . . . . 146 12-11 port d i/o circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 12-12 port d control register (pdcr) . . . . . . . . . . . . . . . . . . . . . . . 147 13-1 irq module block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 151 13-2 irq i/o register summary. . . . . . . . . . . . . . . . . . . . . . . . . . . 151 13-3 irq status and control register (intscr) . . . . . . . . . . . . . . 153 13-4 configuration register 2 (config2) . . . . . . . . . . . . . . . . . . . 154 14-1 kbi i/o register summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 14-2 keyboard interrupt block diagram . . . . . . . . . . . . . . . . . . . . . 156 14-3 keyboard status and control register (kbscr) . . . . . . . . . . 159 14-4 keyboard interrupt enable register (kbier) . . . . . . . . . . . . . 160 15-1 cop block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 15-2 configuration register 1 (config1) . . . . . . . . . . . . . . . . . . . 166 15-3 cop control register (copctl) . . . . . . . . . . . . . . . . . . . . . . 167 16-1 lvi module block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 16-2 configuration register 2 (config2) . . . . . . . . . . . . . . . . . . . 170 16-3 configuration register 1 (config1) . . . . . . . . . . . . . . . . . . . 171 17-1 break module block diagram . . . . . . . . . . . . . . . . . . . . . . . . . 175 17-2 break i/o register summary . . . . . . . . . . . . . . . . . . . . . . . . . 175 17-3 break status and control register (brkscr). . . . . . . . . . . . 177 17-4 break address register high (brkh) . . . . . . . . . . . . . . . . . . 178 17-5 break address register low (brkl) . . . . . . . . . . . . . . . . . . . 178 17-6 break status register (bsr) . . . . . . . . . . . . . . . . . . . . . . . . . 178 17-7 break flag control register (bfcr) . . . . . . . . . . . . . . . . . . . 180 list of figures technical data mc68h(r)c08jl3 ? rev. 4 18 list of figures motorola figure title page 18-1 rc vs. frequency (5v @25 c) . . . . . . . . . . . . . . . . . . . . . . . 186 18-2 rc vs. frequency (3v @25 c) . . . . . . . . . . . . . . . . . . . . . . . 189 18-3 typical operating i dd , with all modules turned on (25 c) . . 190 18-4 typical wait mode i dd , with adc turned on (25 c) . . . . . . 190 18-5 typical stop mode i dd , with all modules disabled (25 c). . . 190 19-1 20-pin pdip (case #738) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 19-2 20-pin soic (case #751d) . . . . . . . . . . . . . . . . . . . . . . . . . . 194 19-3 28-pin pdip (case #710) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 19-4 28-pin soic (case #751f). . . . . . . . . . . . . . . . . . . . . . . . . . . 195 mc68h(r)c08jl3 ? rev. 4 technical data motorola list of tables 19 technical data ?mc68h(r)c08jl3 list of tables table title page 1-1 summary of device variations . . . . . . . . . . . . . . . . . . . . . . . . . 21 1-2 pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2-1 vector addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6-1 instruction set summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6-2 opcode map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 7-1 signal name conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 7-2 pin bit set timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 7-3 interrupt sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 7-4 sim registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 9-1 monitor mode entry requirements and options. . . . . . . . . . . . 98 9-2 monitor mode vector differences . . . . . . . . . . . . . . . . . . . . . . . 99 9-3 monitor baud rate selection . . . . . . . . . . . . . . . . . . . . . . . . . 100 9-4 read (read memory) command . . . . . . . . . . . . . . . . . . . . . 102 9-5 write (write memory) command. . . . . . . . . . . . . . . . . . . . . 102 9-6 iread (indexed read) command . . . . . . . . . . . . . . . . . . . . . 103 9-7 iwrite (indexed write) command . . . . . . . . . . . . . . . . . . . . 103 9-8 readsp (read stack pointer) command . . . . . . . . . . . . . . . 104 9-9 run (run user program) command . . . . . . . . . . . . . . . . . . . 104 10-1 pin name conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 10-2 prescaler selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 10-3 mode, edge, and level selection . . . . . . . . . . . . . . . . . . . . . . 124 11-1 mux channel select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 11-2 adc clock divide ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 list of tables technical data mc68h(r)c08jl3 ? rev. 4 20 list of tables motorola table title page 12-1 port a pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 12-2 port b pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 12-3 port d pin functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 18-1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 182 18-2 operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 18-3 thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 18-4 dc electrical characteristics (5v) . . . . . . . . . . . . . . . . . . . . . 184 18-5 control timing (5v) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 18-6 oscillator component specifications (5v) . . . . . . . . . . . . . . . 186 18-7 dc electrical characteristics (3v) . . . . . . . . . . . . . . . . . . . . . 187 18-8 control timing (3v) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 18-9 oscillator component specifications (3v) . . . . . . . . . . . . . . . 189 18-10 adc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 mc68h(r)c08jl3 ? rev. 4 technical data motorola general description 21 technical data ?mc68h(r)c08jl3 section 1. general description 1.1 contents 1.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 1.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 1.4 mcu block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 1.5 pin assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 1.6 pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 1.2 introduction the mc68h(r)c08jl3 is a member of the low-cost, high-performance m68hc08 family of 8-bit microcontroller units (mcus). the m68hc08 family is based on the customer-specified integrated circuit (csic) design strategy. all mcus in the family use the enhanced m68hc08 central processor unit (cpu08) and are available with a variety of modules, memory sizes and types, and package types. all references to the mc68h(r)c08jl3 in this data book apply equally to the mc68h(r)c08jk3 and mc68h(r)c08jk1, unless otherwise stated. table 1-1. summary of device variations device rom size pin count mc68h(r)c08jl3 4096 bytes 28 pins mc68h(r)c08jk3 4096 bytes 20 pins mc68h(r)c08jk1 1536 bytes 20 pins general description technical data mc68h(r)c08jl3 ? rev. 4 22 general description motorola 1.3 features features of the mc68h(r)c08jl3 include the following: high-performance m68hc08 architecture fully upward-compatible object code with m6805, m146805, and m68hc05 families low-power design; fully static with stop and wait modes 5v and 3v operating voltages 8mhz internal bus operation rc-oscillator circuit or crystal-oscillator options rom security 1 user read-only memory (rom) 4096 bytes for mc68h(r)c08jl3/jk3 1536 bytes for mc68h(r)c08jk1 128 bytes of on-chip random-access memory (ram) 2-channel, 16-bit timer interface module (tim) 12-channel, 8-bit analog-to-digital converter (adc) 23 general purpose i/o ports for mc68h(r)c08jl3: 7 keyboard interrupt with internal pull-up 10 led drivers ? 25ma open-drain i/o with pull-up 2 icap/ocap/pwm 15 general purpose i/o ports for mc68h(r)c08jk3/jk1: 1 keyboard interrupt with internal pull-up (with rc oscillator option selected) 4 led drivers ? 25ma open-drain i/o with pull-up 2 icap/ocap/pwm 1. no security feature is absolutely secure. however, motorola? strategy is to make reading or copying the rom difficult for unauthorized users. general description mcu block diagram mc68h(r)c08jl3 ? rev. 4 technical data motorola general description 23 system protection features: optional computer operating properly (cop) reset optional low-voltage detection with reset and selectable trip points for 3v and 5v operation. illegal opcode detection with reset illegal address detection with reset master reset pin with internal pull-up and power-on reset irq1 with programmable pull-up and schmitt-trigger input 28-pin pdip and 28-pin soic packages for mc68h(r)c08jl3 20-pin pdip and 20-pin soic packages for mc68h(r)c08jk3/jk1 features of the cpu08 include the following: enhanced hc05 programming model extensive loop control functions 16 addressing modes (eight more than the hc05) 16-bit index register and stack pointer memory-to-memory data transfers fast 8 8 multiply instruction fast 16/8 divide instruction binary-coded decimal (bcd) instructions optimization for controller applications efficient c language support 1.4 mcu block diagram figure 1-1 shows the structure of the mc68h(r)c08jl3. general description technical data mc68h(r)c08jl3 ? rev. 4 24 general description motorola figure 1-1. mcu block diagram rst , irq1 : pin has internal 30k pull-up ptd[6:7]: pins have 25ma open-drain output & programmable 5k pull-up pta[0:5], ptd[2:3], ptd[6:7]: pin has led drive pta[0:6]: pins have programmable keyboard interrupt and pull-up pta[0:5] and ptd[0:1]: not available on 20-pin devices ?mc68h(r)c08jk3/jk1 mc68h(r)c08jl3/jk3: 4096 bytes mc68h(r)c08jk1: 1536 bytes user rom cond code reg v 1 1 i n z c h index reg cpu control stk pntr alu 68hc08 cpu accum program counter cpu registers 128 bytes ram osc1 rst irq1 vdd vss 16-bit timer module cop module power-on reset module break module mode select module system integration module x-tal oscillator or rc-oscillator power supply and voltage regulator ptb[0:7] ptb ddrb monitor rom 960 bytes ptd[0:7] pta/kbi[0:6] 8-bit adc adc[0:7]/ ptb[0:7] tch0/ptd4 tch1/ptd5 osc2/rcclk/pta6 ptd ddrd pta ddra adc[11:8]/ ptd[0:3] general description pin assignments mc68h(r)c08jl3 ? rev. 4 technical data motorola general description 25 1.5 pin assignments the mc68h(r)c08jl3 is available in 28-pin packages and the mc68h(r)c08jk3/jk1 in 20-pin packages. figure 1-2 shows the pin assignment for the two packages. figure 1-2. mcu pin assignments 1 2 3 4 5 6 7 28 27 26 25 24 23 22 21 20 19 18 12 13 14 17 16 15 8 9 10 11 1 2 3 4 5 6 7 20 19 18 17 16 15 14 13 12 11 8 9 10 rst pta5 ptd4 ptd5 ptd2 pta4 ptd3 ptb0 ptb1 ptd1 ptb2 ptb3 ptd0 ptb4 irq1 pta0 vss osc1 osc2/pta6 pta1 vdd pta2 pta3 ptb7 ptb6 ptb5 ptd7 ptd6 rst ptd4 ptd5 ptd2 ptd3 ptb0 ptb1 ptb2 ptb3 ptb4 irq1 vss osc1 osc2/pta6 vdd ptb7 ptb6 ptb5 ptd7 ptd6 28-pin assignment mc68h(r)c08jl3 20-pin assignment mc68h(r)c08jk3/jk1 pins not bonded out on 20-pin package: pta0, pta1, pta2, pta3, pta4, pta5, ptd0, ptd1. general description technical data mc68h(r)c08jl3 ? rev. 4 26 general description motorola 1.6 pin functions description of the pin functions are provided in table 1-2 . note: on the 20-pin package, the following pins are not available: pta0, pta1, pta2, pta3, pta4, pta5, ptd0, and ptd1. table 1-2. pin functions pin name pin description in/out voltage level vdd power supply. in 5v or 3v vss power supply ground out 0v rst reset input, active low. with internal pull-up and schmitt trigger input. input vdd irq1 external irq pin. with software programmable internal pull-up and schmitt trigger input. this pin is also used for mode entry selection. input vdd to vdd+v hi osc1 x-tal or rc oscillator input. in analog osc2 for x-tal oscillator option: x-tal oscillator output, this is the inverting osc1 signal. out analog for rc oscillator option: default is rcclk output. shared with pta6/kbi6, with programmable pull-up. in/out vdd pta[0:6] 7-bit general purpose i/o port. in/out vdd shared with 7 keyboard interrupts kbi[0:6]. in vdd each pin has programmable internal pull-up device. in vdd ptb[0:7] 8-bit general purpose i/o port. in/out vdd shared with 8 adc inputs, adc[0:7]. in analog ptd[0:7] 8-bit general purpose i/o port. in/out vdd ptd[3:0] shared with 4 adc inputs, adc[8:11]. input analog ptd[4:5] shared with tim channels, tch0 and tch1. in/out vdd ptd[6:7] can be con?ured as 25ma open-drain output with pull-up. in/out vdd mc68h(r)c08jl3 ? rev. 4 technical data motorola memory 27 technical data ?mc68h(r)c08jl3 section 2. memory 2.1 contents 2.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3 i/o section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.4 monitor rom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.2 introduction the cpu08 can address 64 kbytes of memory space. the memory map, shown in figure 2-1 , includes: 4096 bytes of user rom for mc68h(r)c08jl3/jk3 1536 bytes of user rom for mc68h(r)c08jk1 128 bytes of ram 48 bytes of user-defined vectors 960 bytes of monitor rom memory technical data mc68h(r)c08jl3 ? rev. 4 28 memory motorola $0000 $003f i/o registers 64 bytes $0040 $007f reserved 64 bytes $0080 $00ff ram 128 bytes $0100 $ebff unimplemented 60160 bytes unimplemented 62720 bytes $0100 $f5ff $ec00 $fbff user rom mc68h(r)c08jl3/jk3 4096 bytes user rom mc68h(r)c08jk1 1536 bytes $f600 $fbff $fc00 $fdff monitor rom 512 bytes $fe00 break status register (bsr) $fe01 reset status register (rsr) $fe02 reserved (ubar) $fe03 break flag control register (bfcr) $fe04 interrupt status register 1 (int1) $fe05 interrupt status register 2 (int2) $fe06 interrupt status register 3 (int3) $fe07 reserved $fe08 reserved $fe09 reserved $fe0a reserved $fe0b reserved $fe0c break address high register (brkh) $fe0d break address low register (brkl) $fe0e break status and control register (brkscr) $fe0f reserved $fe10 $ffcf monitor rom 448 bytes $ffd0 $ffff user vectors 48 bytes figure 2-1. memory map memory i/o section mc68h(r)c08jl3 ? rev. 4 technical data motorola memory 29 2.3 i/o section addresses $0000?003f, shown in figure 2-2 , contain most of the control, status, and data registers. additional i/o registers have the following addresses: $fe00 (break status register, bsr) $fe01 (reset status register, rsr) $fe02 (reserved, subar) $fe03 (break flag control register, bfcr) $fe04 (interrupt status register 1, int1) $fe05 (interrupt status register 2, int2) $fe06 (interrupt status register 3, int3) $fe07 (reserved) $fe08 (reserved) $fe09 (reserved) $fe0a (reserved) $fe0b (reserved) $fe0c (break address register high, brkh) $fe0d (break address register low, brkl) $fe0e (break status and control register, brkscr) $fe0f (reserved) $ffff (cop control register, copctl) 2.4 monitor rom the 960 bytes at addresses $fc00?fdff and $fe10?ffcf are reserved rom addresses that contain the instructions for the monitor functions. (see section 9. monitor rom (mon) .) memory technical data mc68h(r)c08jl3 ? rev. 4 30 memory motorola addr. register name bit 7 654321 bit 0 $0000 port a data register (pta) read: 0 pta6 pta5 pta4 pta3 pta2 pta1 pta0 write: reset: unaffected by reset $0001 port b data register (ptb) read: ptb7 ptb6 ptb5 ptb4 ptb3 ptb2 ptb1 ptb0 write: reset: unaffected by reset $0002 unimplemented read: write: $0003 port d data register (ptd) read: ptd7 ptd6 ptd5 ptd4 ptd3 ptd2 ptd1 ptd0 write: reset: unaffected by reset $0004 data direction register a (ddra) read: 0 ddra6 ddra5 ddra4 ddra3 ddra2 ddra1 ddra0 write: reset: 00000000 $0005 data direction register b (ddrb) read: ddrb7 ddrb6 ddrb5 ddrb4 ddrb3 ddrb2 ddrb1 ddrb0 write: reset: 00000000 $0006 unimplemented read: write: $0007 data direction register d (ddrd) read: ddrd7 ddrd6 ddrd5 ddrd4 ddrd3 ddrd2 ddrd1 ddrd0 write: reset: 00000000 $0008 $0009 unimplemented read: write: $000a port d control register (pdcr) read: 0000 slowd7 slowd6 ptdpu7 ptdpu6 write: reset: 00000000 = unimplemented r = reserved figure 2-2. control, status, and data registers (sheet 1 of 5) memory monitor rom mc68h(r)c08jl3 ? rev. 4 technical data motorola memory 31 $000b $000c unimplemented read: write: $000d port a input pull-up enable register (ptapue) read: pta6en ptapue6 ptapue5 ptapue4 ptapue3 ptapue2 ptapue1 ptapue0 write: reset: 00000000 $000e $0019 unimplemented read: write: $001a keyboard status and control register (kbscr) read: 0000 keyf 0 imaskk modek write: ackk reset: 00000000 $001b keyboard interrupt enable register (kbier) read: 0 kbie6 kbie5 kbie4 kbie3 kbie2 kbie1 kbie0 write: reset: 00000000 $001c unimplemented read: write: $001d irq status and control register (intscr) read: 0000 irqf1 0 imask1 mode1 write: ack1 reset: 00000000 $001e configuration register 2 (config2) ? read: irqpud r r lvit1 lvit0 r r r write: reset: 0 0 0 0* 0* 0 0 0 $001f configuration register 1 (config1) ? read: coprs r r lvid r ssrec stop copd write: reset: 00000000 ? one-time writable register after each reset. * lvit1 and lvit0 reset to logic 0 by a power-on reset (por) only. $0020 tim status and control register (tsc) read: tof toie tstop 00 ps2 ps1 ps0 write: 0 trst reset: 00100000 addr. register name bit 7 654321 bit 0 = unimplemented r = reserved figure 2-2. control, status, and data registers (sheet 2 of 5) memory technical data mc68h(r)c08jl3 ? rev. 4 32 memory motorola $0021 tim counter register high (tcnth) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 00000000 $0022 tim counter register low (tcntl) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 00000000 $0023 tim counter modulo register high (tmodh) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 11111111 $0024 tim counter modulo register low (tmodl) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 11111111 $0025 tim channel 0 status and control register (tsc0) read: ch0f ch0ie ms0b ms0a els0b els0a tov0 ch0max write: 0 reset: 00000000 $0026 tim channel 0 register high (tch0h) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: indeterminate after reset $0027 tim channel 0 register low (tch0l) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: indeterminate after reset $0028 tim channel 1 status and control register (tsc1) read: ch1f ch1ie 0 ms1a els1b els1a tov1 ch1max write: 0 reset: 00000000 $0029 tim channel 1 register high (tch1h) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: indeterminate after reset $002a tim channel 1 register low (tch1l) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: indeterminate after reset addr. register name bit 7 654321 bit 0 = unimplemented r = reserved figure 2-2. control, status, and data registers (sheet 3 of 5) memory monitor rom mc68h(r)c08jl3 ? rev. 4 technical data motorola memory 33 $002b $003b unimplemented read: write: $003c adc status and control register (adscr) read: coco aien adco ch4 ch3 ch2 ch1 ch0 write: reset: 00011111 $003d adc data register (adr) read: ad7 ad6 ad5 ad4 ad3 ad2 ad1 ad0 write: reset: indeterminate after reset $003e adc input clock register (adiclk) read: adiv2 adiv1 adiv0 00000 write: reset: 00000000 $003f unimplemented read: write: $fe00 break status register (bsr) read: rrrrrr sbsw r write: see note reset: 0 note: writing a logic 0 clears sbsw. $fe01 reset status register (rsr) read: por pin cop ilop ilad modrst lvi 0 write: por: 10000000 $fe02 reserved read: rrrrrrrr write: $fe03 break flag control register (bfcr) read: bcfe rrrrrrr write: reset: 0 $fe04 interrupt status register 1 (int1) read: 0 if5 if4 if3 0 if1 0 0 write: rrrrrrrr reset: 00000000 addr. register name bit 7 654321 bit 0 = unimplemented r = reserved figure 2-2. control, status, and data registers (sheet 4 of 5) memory technical data mc68h(r)c08jl3 ? rev. 4 34 memory motorola $fe05 interrupt status register 2 (int2) read: if14 0000000 write: rrrrrrrr reset: 00000000 $fe06 interrupt status register 3 (int3) read: 0000000 if15 write: rrrrrrrr reset: 00000000 $fe07 $fe0b reserved read: rrrrrrrr write: $fe0c break address high register (brkh) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 00000000 $fe0d break address low register (brkl) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 00000000 $fe0e break status and control register (brkscr) read: brke brka 000000 write: reset: 00000000 $ffff cop control register (copctl) read: low byte of reset vector write: writing clears cop counter (any value) reset: unaffected by reset addr. register name bit 7 654321 bit 0 = unimplemented r = reserved figure 2-2. control, status, and data registers (sheet 5 of 5) memory monitor rom mc68h(r)c08jl3 ? rev. 4 technical data motorola memory 35 . table 2-1. vector addresses vector priority vector address vector lowest if15 $ffde adc conversion complete vector (high) $ffdf adc conversion complete vector (low) if14 $ffe0 keyboard vector (high) $ffe1 keyboard vector (low) if13 to if6 not used if5 $fff2 tim over?w vector (high) $fff3 tim over?w vector (low) if4 $fff4 tim channel 1 vector (high) $fff5 tim channel 1 vector (low) if3 $fff6 tim channel 0 vector (high) $fff7 tim channel 0 vector (low) if2 not used if1 $fffa irq vector (high) $fffb irq vector (low) $fffc swi vector (high) $fffd swi vector (low) $fffe reset vector (high) highest $ffff reset vector (low) memory technical data mc68h(r)c08jl3 ? rev. 4 36 memory motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola random-access memory (ram) 37 technical data ?mc68h(r)c08jl3 section 3. random-access memory (ram) 3.1 contents 3.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 3.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 3.2 introduction this section describes the 128 bytes of ram. 3.3 functional description addresses $0080 through $00ff are ram locations. the location of the stack ram is programmable. the 16-bit stack pointer allows the stack to be anywhere in the 64-kbyte memory space. note: for correct operation, the stack pointer must point only to ram locations. within page zero are 128 bytes of ram. because the location of the stack ram is programmable, all page zero ram locations can be used for i/o control and user data or code. when the stack pointer is moved from its reset location at $00ff, direct addressing mode instructions can access efficiently all page zero ram locations. page zero ram, therefore, provides ideal locations for frequently accessed global variables. before processing an interrupt, the cpu uses five bytes of the stack to save the contents of the cpu registers. note: for m6805 compatibility, the h register is not stacked. random-access memory (ram) technical data mc68h(r)c08jl3 ? rev. 4 38 random-access memory (ram) motorola during a subroutine call, the cpu uses two bytes of the stack to store the return address. the stack pointer decrements during pushes and increments during pulls. note: be careful when using nested subroutines. the cpu may overwrite data in the ram during a subroutine or during the interrupt stacking operation. mc68h(r)c08jl3 ? rev. 4 technical data motorola read-only memory (rom) 39 technical data ?mc68h(r)c08jl3 section 4. read-only memory (rom) 4.1 contents 4.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.2 introduction this section describes the 4096 or 1536 bytes of read-only memory (rom) and 48 bytes of user vectors. 4.3 functional description these addresses are user rom locations: $ec00?fbff; user memory, 4096 bytes on mc68h(r)c08jl3/jk3. $f600?fbff; user memory, 1536 bytes on mc68h(r)c08jk1. $ffd0?ffff (these locations are reserved for user-defined interrupt and reset vectors.) note: a security feature prevents viewing of the rom contents. 1 1. no security feature is absolutely secure. however, motorola? strategy is to make reading or copying the rom contents difficult for unauthorized users. read-only memory (rom) technical data mc68h(r)c08jl3 ? rev. 4 40 read-only memory (rom) motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola configuration register (config) 41 technical data ?mc68h(r)c08jl3 section 5. configuration register (config) 5.1 contents 5.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 5.2 introduction this section describes the configuration registers (config1 and config2). the configuration registers enables or disables the following options: stop mode recovery time (32 2oscout cycles or 4096 2oscout cycles) stop instruction computer operating properly module (cop) cop reset period (coprs), (2 13 ? 4 ) 2oscout or (2 18 ? 4 ) 2oscout enable lvi circuit select lvi trip voltage con?uration register (config) technical data mc68h(r)c08jl3 ? rev. 4 42 configuration register (config) motorola 5.3 functional description the configuration register is used in the initialization of various options. the configuration register can be written once after each reset. all of the configuration register bits are cleared during reset. since the various options affect the operation of the mcu it is recommended that this register be written immediately after reset. the configuration register is located at $001e and $001f, and may be read at anytime. note: the config registers are one-time writable by the user after each reset. upon a reset, the config registers default to predetermined settings as shown in figure 5-1 and figure 5-2 . irqpud ?irq1 pin pull-up control bit 1 = internal pull-up is disconnected 0 = internal pull-up is connected between irq1 pin and v dd lvit1, lvit0 ?low voltage inhibit trip voltage selection bits detail description of the lvi control signals is given in section 16. address: $001e bit 7 654321 bit 0 read: irqpud r r lvit1 lvit0 r r r write: reset: 0 0 0 not affected not affected 000 por: 00000000 r = reserved figure 5-1. configuration register 2 (config2) configuration register (config) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola configuration register (config) 43 coprs cop reset period selection bit 1 = cop reset cycle = (2 13 ?2 4 ) 2oscout 0 = cop reset cycle = (2 18 ?2 4 ) 2oscout lvid low voltage inhibit disable bit 1 = low voltage inhibit disabled 0 = low voltage inhibit enabled ssrec ?short stop recovery bit ssrec enables the cpu to exit stop mode with a delay of 32 oscxclk cycles instead of a 4096 2oscout cycle delay. 1 = stop mode recovery after 32 2oscout cycles 0 = stop mode recovery after 4096 2oscout cycles note: exiting stop mode by pulling reset will result in the long stop recovery. if using an external crystal, do not set the ssrec bit. stop enables the stop instruction. 1 = stop instruction enabled 0 = stop instruction treated as illegal opcode copd ?cop disable bit copd disables the cop module. (see section 15. computer operating properly (cop) .) 1 = cop module disabled 0 = cop module enabled address: $001f bit 7 654321 bit 0 read: coprs r r lvid r ssrec stop copd write: reset: 00000000 r = reserved figure 5-2. configuration register 1 (config1) con?uration register (config) technical data mc68h(r)c08jl3 ? rev. 4 44 configuration register (config) motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 45 technical data ?mc68h(r)c08jl3 section 6. central processor unit (cpu) 6.1 contents 6.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.4 cpu registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.4.1 accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.4.2 index register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.4.3 stack pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.4.4 program counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.4.5 condition code register . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.5 arithmetic/logic unit (alu) . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.7 cpu during break interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.8 instruction set summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.9 opcode map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.2 introduction the m68hc08 cpu (central processor unit) is an enhanced and fully object-code-compatible version of the m68hc05 cpu. the cpu08 reference manual (motorola document order number cpu08rm/ad) contains a description of the cpu instruction set, addressing modes, and architecture. central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 46 central processor unit (cpu) motorola 6.3 features object code fully upward-compatible with m68hc05 family 16-bit stack pointer with stack manipulation instructions 16-bit index register with x-register manipulation instructions 8-mhz cpu internal bus frequency 64-kbyte program/data memory space 16 addressing modes memory-to-memory data moves without using accumulator fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions enhanced binary-coded decimal (bcd) data handling modular architecture with expandable internal bus definition for extension of addressing range beyond 64 kbytes low-power stop and wait modes 6.4 cpu registers figure 6-1 shows the five cpu registers. cpu registers are not part of the memory map. central processor unit (cpu) cpu registers mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 47 figure 6-1. cpu registers 6.4.1 accumulator the accumulator is a general-purpose 8-bit register. the cpu uses the accumulator to hold operands and the results of arithmetic/logic operations. accumulator (a) index register (h:x) stack pointer (sp) program counter (pc) condition code register (ccr) carry/borrow flag zero flag negative flag interrupt mask half-carry flag two? complement overflow flag v1 1h i nzc h x 0 0 0 0 7 15 15 15 70 bit 7 654321 bit 0 read: write: reset: unaffected by reset figure 6-2. accumulator (a) central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 48 central processor unit (cpu) motorola 6.4.2 index register the 16-bit index register allows indexed addressing of a 64-kbyte memory space. h is the upper byte of the index register, and x is the lower byte. h:x is the concatenated 16-bit index register. in the indexed addressing modes, the cpu uses the contents of the index register to determine the conditional address of the operand. the index register can serve also as a temporary data storage location. 6.4.3 stack pointer the stack pointer is a 16-bit register that contains the address of the next location on the stack. during a reset, the stack pointer is preset to $00ff. the reset stack pointer (rsp) instruction sets the least significant byte to $ff and does not affect the most significant byte. the stack pointer decrements as data is pushed onto the stack and increments as data is pulled from the stack. in the stack pointer 8-bit offset and 16-bit offset addressing modes, the stack pointer can function as an index register to access data on the stack. the cpu uses the contents of the stack pointer to determine the conditional address of the operand. bit 15 1413121110987654321 bit 0 read: write: reset: 00000000 xxxxxxxx x = indeterminate figure 6-3. index register (h:x) central processor unit (cpu) cpu registers mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 49 note: the location of the stack is arbitrary and may be relocated anywhere in ram. moving the sp out of page 0 ($0000 to $00ff) frees direct address (page 0) space. for correct operation, the stack pointer must point only to ram locations. 6.4.4 program counter the program counter is a 16-bit register that contains the address of the next instruction or operand to be fetched. normally, the program counter automatically increments to the next sequential memory location every time an instruction or operand is fetched. jump, branch, and interrupt operations load the program counter with an address other than that of the next sequential location. during reset, the program counter is loaded with the reset vector address located at $fffe and $ffff. the vector address is the address of the first instruction to be executed after exiting the reset state. 6.4.5 condition code register the 8-bit condition code register contains the interrupt mask and five flags that indicate the results of the instruction just executed. bits 6 and bit 15 1413121110987654321 bit 0 read: write: reset: 0000000011111111 figure 6-4. stack pointer (sp) bit 15 1413121110987654321 bit 0 read: write: reset: loaded with vector from $fffe and $ffff figure 6-5. program counter (pc) central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 50 central processor unit (cpu) motorola 5 are set permanently to logic 1. the following paragraphs describe the functions of the condition code register. v ?overflow flag the cpu sets the overflow flag when a two's complement overflow occurs. the signed branch instructions bgt, bge, ble, and blt use the overflow flag. 1 = overflow 0 = no overflow h ?half-carry flag the cpu sets the half-carry flag when a carry occurs between accumulator bits 3 and 4 during an add-without-carry (add) or add- with-carry (adc) operation. the half-carry flag is required for binary- coded decimal (bcd) arithmetic operations. the daa instruction uses the states of the h and c flags to determine the appropriate correction factor. 1 = carry between bits 3 and 4 0 = no carry between bits 3 and 4 bit 7 654321 bit 0 read: v1 1h i nzc write: reset: x 1 1x1xxx x = indeterminate figure 6-6. condition code register (ccr) central processor unit (cpu) cpu registers mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 51 i ?interrupt mask when the interrupt mask is set, all maskable cpu interrupts are disabled. cpu interrupts are enabled when the interrupt mask is cleared. when a cpu interrupt occurs, the interrupt mask is set automatically after the cpu registers are saved on the stack, but before the interrupt vector is fetched. 1 = interrupts disabled 0 = interrupts enabled note: to maintain m6805 family compatibility, the upper byte of the index register (h) is not stacked automatically. if the interrupt service routine modifies h, then the user must stack and unstack h using the pshh and pulh instructions. after the i bit is cleared, the highest-priority interrupt request is serviced first. a return-from-interrupt (rti) instruction pulls the cpu registers from the stack and restores the interrupt mask from the stack. after any reset, the interrupt mask is set and can be cleared only by the clear interrupt mask software instruction (cli). n ?negative flag the cpu sets the negative flag when an arithmetic operation, logic operation, or data manipulation produces a negative result, setting bit 7 of the result. 1 = negative result 0 = non-negative result z ?zero flag the cpu sets the zero flag when an arithmetic operation, logic operation, or data manipulation produces a result of $00. 1 = zero result 0 = non-zero result central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 52 central processor unit (cpu) motorola c ?carry/borrow flag the cpu sets the carry/borrow flag when an addition operation produces a carry out of bit 7 of the accumulator or when a subtraction operation requires a borrow. some instructions ?such as bit test and branch, shift, and rotate ?also clear or set the carry/borrow flag. 1 = carry out of bit 7 0 = no carry out of bit 7 6.5 arithmetic/logic unit (alu) the alu performs the arithmetic and logic operations defined by the instruction set. refer to the cpu08 reference manual (motorola document order number cpu08rm/ad) for a description of the instructions and addressing modes and more detail about the architecture of the cpu. 6.6 low-power modes the wait and stop instructions put the mcu in low power-consumption standby modes. 6.6.1 wait mode the wait instruction: clears the interrupt mask (i bit) in the condition code register, enabling interrupts. after exit from wait mode by interrupt, the i bit remains clear. after exit by reset, the i bit is set. disables the cpu clock central processor unit (cpu) cpu during break interrupts mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 53 6.6.2 stop mode the stop instruction: clears the interrupt mask (i bit) in the condition code register, enabling external interrupts. after exit from stop mode by external interrupt, the i bit remains clear. after exit by reset, the i bit is set. disables the cpu clock after exiting stop mode, the cpu clock begins running after the oscillator stabilization delay. 6.7 cpu during break interrupts if a break module is present on the mcu, the cpu starts a break interrupt by: loading the instruction register with the swi instruction loading the program counter with $fffc:$fffd or with $fefc:$fefd in monitor mode the break interrupt begins after completion of the cpu instruction in progress. if the break address register match occurs on the last cycle of a cpu instruction, the break interrupt begins immediately. a return-from-interrupt instruction (rti) in the break routine ends the break interrupt and returns the mcu to normal operation if the break interrupt has been deasserted. 6.8 instruction set summary 6.9 opcode map see table 6-2 . central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 54 central processor unit (cpu) motorola table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc adc # opr adc opr adc opr adc opr ,x adc opr ,x adc ,x adc opr ,sp adc opr ,sp add with carry a ? (a) + (m) + (c) imm dir ext ix2 ix1 ix sp1 sp2 a9 b9 c9 d9 e9 f9 9ee9 9ed9 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 add # opr add opr add opr add opr ,x add opr ,x add ,x add opr ,sp add opr ,sp add without carry a ? (a) + (m) imm dir ext ix2 ix1 ix sp1 sp2 ab bb cb db eb fb 9eeb 9edb ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 ais # opr add immediate value (signed) to sp sp ? (sp) + (16 ?m) imm a7 ii 2 aix # opr add immediate value (signed) to h:x h:x ? (h:x) + (16 ?m) imm af ii 2 and # opr and opr and opr and opr ,x and opr ,x and ,x and opr ,sp and opr ,sp logical and a ? (a) & (m) 0 imm dir ext ix2 ix1 ix sp1 sp2 a4 b4 c4 d4 e4 f4 9ee4 9ed4 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 asl opr asla aslx asl opr ,x asl ,x asl opr ,sp arithmetic shift left (same as lsl) dir inh inh ix1 ix sp1 38 48 58 68 78 9e68 dd ff ff 4 1 1 4 3 5 asr opr asra asrx asr opr ,x asr opr ,x asr opr ,sp arithmetic shift right dir inh inh ix1 ix sp1 37 47 57 67 77 9e67 dd ff ff 4 1 1 4 3 5 bcc rel branch if carry bit clear pc ? (pc) + 2 + rel ? (c) = 0 rel 24 rr 3 bclr n , opr clear bit n in m mn ? 0 dir (b0) dir (b1) dir (b2) dir (b3) dir (b4) dir (b5) dir (b6) dir (b7) 11 13 15 17 19 1b 1d 1f dd dd dd dd dd dd dd dd 4 4 4 4 4 4 4 4 c b0 b7 0 b0 b7 c central processor unit (cpu) opcode map mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 55 bcs rel branch if carry bit set (same as blo) pc ? (pc) + 2 + rel ? (c) = 1 rel 25 rr 3 beq rel branch if equal pc ? (pc) + 2 + rel ? (z) = 1 rel 27 rr 3 bge opr branch if greater than or equal to (signed operands) pc ? (pc) + 2 + rel ? (n ? v ) = 0 rel 90 rr 3 bgt opr branch if greater than (signed operands) pc ? (pc) + 2 + rel ? (z) | (n ? v ) = 0 rel 92 rr 3 bhcc rel branch if half carry bit clear pc ? (pc) + 2 + rel ? (h) = 0 rel 28 rr 3 bhcs rel branch if half carry bit set pc ? (pc) + 2 + rel ? (h) = 1 rel 29 rr 3 bhi rel branch if higher pc ? (pc) + 2 + rel ? (c) | (z) = 0 rel 22 rr 3 bhs rel branch if higher or same (same as bcc) pc ? (pc) + 2 + rel ? (c) = 0 rel 24 rr 3 bih rel branch if irq pin high pc ? (pc) + 2 + rel ? irq = 1 rel 2f rr 3 bil rel branch if irq pin low pc ? (pc) + 2 + rel ? irq = 0 rel 2e rr 3 bit # opr bit opr bit opr bit opr ,x bit opr ,x bit ,x bit opr ,sp bit opr ,sp bit test (a) & (m) 0 imm dir ext ix2 ix1 ix sp1 sp2 a5 b5 c5 d5 e5 f5 9ee5 9ed5 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 ble opr branch if less than or equal to (signed operands) pc ? (pc) + 2 + rel ? (z) | (n ? v ) = 1 rel 93 rr 3 blo rel branch if lower (same as bcs) pc ? (pc) + 2 + rel ? (c) = 1 rel 25 rr 3 bls rel branch if lower or same pc ? (pc) + 2 + rel ? (c) | (z) = 1 rel 23 rr 3 blt opr branch if less than (signed operands) pc ? (pc) + 2 + rel ? (n ? v ) = 1 rel 91 rr 3 bmc rel branch if interrupt mask clear pc ? (pc) + 2 + rel ? (i) = 0 rel 2c rr 3 bmi rel branch if minus pc ? (pc) + 2 + rel ? (n) = 1 rel 2b rr 3 bms rel branch if interrupt mask set pc ? (pc) + 2 + rel ? (i) = 1 rel 2d rr 3 bne rel branch if not equal pc ? (pc) + 2 + rel ? (z) = 0 rel 26 rr 3 bpl rel branch if plus pc ? (pc) + 2 + rel ? (n) = 0 rel 2a rr 3 bra rel branch always pc ? (pc) + 2 + rel rel 20 rr 3 table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 56 central processor unit (cpu) motorola brclr n , opr , rel branch if bit n in m clear pc ? (pc) + 3 + rel ? (mn) = 0 dir (b0) dir (b1) dir (b2) dir (b3) dir (b4) dir (b5) dir (b6) dir (b7) 01 03 05 07 09 0b 0d 0f dd rr dd rr dd rr dd rr dd rr dd rr dd rr dd rr 5 5 5 5 5 5 5 5 brn rel branch never pc ? (pc) + 2 rel 21 rr 3 brset n , opr , rel branch if bit n in m set pc ? (pc) + 3 + rel ? (mn) = 1 dir (b0) dir (b1) dir (b2) dir (b3) dir (b4) dir (b5) dir (b6) dir (b7) 00 02 04 06 08 0a 0c 0e dd rr dd rr dd rr dd rr dd rr dd rr dd rr dd rr 5 5 5 5 5 5 5 5 bset n , opr set bit n in m mn ? 1 dir (b0) dir (b1) dir (b2) dir (b3) dir (b4) dir (b5) dir (b6) dir (b7) 10 12 14 16 18 1a 1c 1e dd dd dd dd dd dd dd dd 4 4 4 4 4 4 4 4 bsr rel branch to subroutine pc ? (pc) + 2; push (pcl) sp ? (sp) ?1; push (pch) sp ? (sp) ?1 pc ? (pc) + rel rel ad rr 4 cbeq opr,rel cbeqa # opr,rel cbeqx # opr,rel cbeq opr, x+ ,rel cbeq x+ ,rel cbeq opr, sp ,rel compare and branch if equal pc ? (pc) + 3 + rel ? (a) ?(m) = $00 pc ? (pc) + 3 + rel ? (a) ?(m) = $00 pc ? (pc) + 3 + rel ? (x) ?(m) = $00 pc ? (pc) + 3 + rel ? (a) ?(m) = $00 pc ? (pc) + 2 + rel ? (a) ?(m) = $00 pc ? (pc) + 4 + rel ? (a) ?(m) = $00 dir imm imm ix1+ ix+ sp1 31 41 51 61 71 9e61 dd rr ii rr ii rr ff rr rr ff rr 5 4 4 5 4 6 clc clear carry bit c ? 0 ?inh 98 1 cli clear interrupt mask i ? 0 0 inh 9a 2 clr opr clra clrx clrh clr opr ,x clr ,x clr opr ,sp clear m ? $00 a ? $00 x ? $00 h ? $00 m ? $00 m ? $00 m ? $00 001 dir inh inh inh ix1 ix sp1 3f 4f 5f 8c 6f 7f 9e6f dd ff ff 3 1 1 1 3 2 4 table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc central processor unit (cpu) opcode map mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 57 cmp # opr cmp opr cmp opr cmp opr ,x cmp opr ,x cmp ,x cmp opr ,sp cmp opr ,sp compare a with m (a) ?(m) imm dir ext ix2 ix1 ix sp1 sp2 a1 b1 c1 d1 e1 f1 9ee1 9ed1 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 com opr coma comx com opr ,x com ,x com opr ,sp complement (one s complement) m ? (m ) = $ff ?(m) a ? (a ) = $ff ?(m) x ? (x ) = $ff ?(m) m ? (m ) = $ff ?(m) m ? (m ) = $ff ?(m) m ? (m ) = $ff ?(m) 0 1 dir inh inh ix1 ix sp1 33 43 53 63 73 9e63 dd ff ff 4 1 1 4 3 5 cphx # opr cphx opr compare h:x with m (h:x) ?(m:m + 1) imm dir 65 75 ii ii+1 dd 3 4 cpx # opr cpx opr cpx opr cpx ,x cpx opr ,x cpx opr ,x cpx opr ,sp cpx opr ,sp compare x with m (x) ?(m) imm dir ext ix2 ix1 ix sp1 sp2 a3 b3 c3 d3 e3 f3 9ee3 9ed3 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 daa decimal adjust a (a) 10 u inh 72 2 dbnz opr,rel dbnza rel dbnzx rel dbnz opr, x ,rel dbnz x ,rel dbnz opr, sp ,rel decrement and branch if not zero a ? (a) ?1 or m ? (m) ?1 or x ? (x) ? 1 pc ? (pc) + 3 + rel ? (result) 1 0 pc ? (pc) + 2 + rel ? (result) 1 0 pc ? (pc) + 2 + rel ? (result) 1 0 pc ? (pc) + 3 + rel ? (result) 1 0 pc ? (pc) + 2 + rel ? (result) 1 0 pc ? (pc) + 4 + rel ? (result) 1 0 dir inh inh ix1 ix sp1 3b 4b 5b 6b 7b 9e6b dd rr rr rr ff rr rr ff rr 5 3 3 5 4 6 dec opr deca decx dec opr ,x dec ,x dec opr ,sp decrement m ? (m) ?1 a ? (a) ?1 x ? (x) ?1 m ? (m) ?1 m ? (m) ?1 m ? (m) ?1 dir inh inh ix1 ix sp1 3a 4a 5a 6a 7a 9e6a dd ff ff 4 1 1 4 3 5 div divide a ? (h:a)/(x) h ? remainder inh 52 7 table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 58 central processor unit (cpu) motorola eor # opr eor opr eor opr eor opr ,x eor opr ,x eor ,x eor opr ,sp eor opr ,sp exclusive or m with a a ? (a ? m) 0 imm dir ext ix2 ix1 ix sp1 sp2 a8 b8 c8 d8 e8 f8 9ee8 9ed8 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 inc opr inca incx inc opr ,x inc ,x inc opr ,sp increment m ? (m) + 1 a ? (a) + 1 x ? (x) + 1 m ? (m) + 1 m ? (m) + 1 m ? (m) + 1 dir inh inh ix1 ix sp1 3c 4c 5c 6c 7c 9e6c dd ff ff 4 1 1 4 3 5 jmp opr jmp opr jmp opr ,x jmp opr ,x jmp ,x jump pc ? jump address dir ext ix2 ix1 ix bc cc dc ec fc dd hh ll ee ff ff 2 3 4 3 2 jsr opr jsr opr jsr opr ,x jsr opr ,x jsr ,x jump to subroutine pc ? (pc) + n ( n = 1, 2, or 3) push (pcl); sp ? (sp) ?1 push (pch); sp ? (sp) ?1 pc ? unconditional address dir ext ix2 ix1 ix bd cd dd ed fd dd hh ll ee ff ff 4 5 6 5 4 lda # opr lda opr lda opr lda opr ,x lda opr ,x lda ,x lda opr ,sp lda opr ,sp load a from m a ? (m) 0 imm dir ext ix2 ix1 ix sp1 sp2 a6 b6 c6 d6 e6 f6 9ee6 9ed6 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 ldhx # opr ldhx opr load h:x from m h:x ? ( m:m + 1 ) 0 imm dir 45 55 ii jj dd 3 4 ldx # opr ldx opr ldx opr ldx opr ,x ldx opr ,x ldx ,x ldx opr ,sp ldx opr ,sp load x from m x ? (m) 0 imm dir ext ix2 ix1 ix sp1 sp2 ae be ce de ee fe 9eee 9ede ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 lsl opr lsla lslx lsl opr ,x lsl ,x lsl opr ,sp logical shift left (same as asl) dir inh inh ix1 ix sp1 38 48 58 68 78 9e68 dd ff ff 4 1 1 4 3 5 table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc c b0 b7 0 central processor unit (cpu) opcode map mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 59 lsr opr lsra lsr x lsr opr ,x lsr ,x lsr opr ,sp logical shift right 0 dir inh inh ix1 ix sp1 34 44 54 64 74 9e64 dd ff ff 4 1 1 4 3 5 mov opr,opr mov opr, x+ mov # opr,opr mov x+ ,opr move (m) destination ? (m) source h:x ? (h:x) + 1 (ix+d, dix+) 0 dd dix+ imd ix+d 4e 5e 6e 7e dd dd dd ii dd dd 5 4 4 4 mul unsigned multiply x:a ? (x) (a) ??inh 42 5 neg opr nega negx neg opr ,x neg ,x neg opr ,sp negate (two s complement) m ? ?m) = $00 ?(m) a ? ?a) = $00 ?(a) x ? ?x) = $00 ?(x) m ? ?m) = $00 ?(m) m ? ?m) = $00 ?(m) dir inh inh ix1 ix sp1 30 40 50 60 70 9e60 dd ff ff 4 1 1 4 3 5 nop no operation none inh 9d 1 nsa nibble swap a a ? (a[3:0]:a[7:4]) inh 62 3 ora # opr ora opr ora opr ora opr ,x ora opr ,x ora ,x ora opr ,sp ora opr ,sp inclusive or a and m a ? (a) | (m) 0 imm dir ext ix2 ix1 ix sp1 sp2 aa ba ca da ea fa 9eea 9eda ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 psha push a onto stack push (a); sp ? (sp) ?1 inh 87 2 pshh push h onto stack push (h); sp ? (sp) ?1 inh 8b 2 pshx push x onto stack push (x); sp ? (sp) ?1 inh 89 2 pula pull a from stack sp ? (sp + 1); pull ( a ) inh 86 2 pulh pull h from stack sp ? (sp + 1); pull ( h ) inh 8a 2 pulx pull x from stack sp ? (sp + 1); pull ( x ) inh 88 2 rol opr rola rolx rol opr ,x rol ,x rol opr ,sp rotate left through carry dir inh inh ix1 ix sp1 39 49 59 69 79 9e69 dd ff ff 4 1 1 4 3 5 table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc b0 b7 c 0 c b0 b7 central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 60 central processor unit (cpu) motorola ror opr rora rorx ror opr ,x ror ,x ror opr ,sp rotate right through carry dir inh inh ix1 ix sp1 36 46 56 66 76 9e66 dd ff ff 4 1 1 4 3 5 rsp reset stack pointer sp ? $ff inh 9c 1 rti return from interrupt sp ? (sp) + 1; pull (ccr) sp ? (sp) + 1; pull (a) sp ? (sp) + 1; pull (x) sp ? (sp) + 1; pull (pch) sp ? (sp) + 1; pull (pcl) inh 80 7 rts return from subroutine sp ? sp + 1 ; pull ( pch) sp ? sp + 1; pull (pcl) inh 81 4 sbc # opr sbc opr sbc opr sbc opr ,x sbc opr ,x sbc ,x sbc opr ,sp sbc opr ,sp subtract with carry a ? (a) ?(m) ?(c) imm dir ext ix2 ix1 ix sp1 sp2 a2 b2 c2 d2 e2 f2 9ee2 9ed2 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 sec set carry bit c ? 1 ?inh 99 1 sei set interrupt mask i ? 1 1 inh 9b 2 sta opr sta opr sta opr ,x sta opr ,x sta ,x sta opr ,sp sta opr ,sp store a in m m ? (a) 0 dir ext ix2 ix1 ix sp1 sp2 b7 c7 d7 e7 f7 9ee7 9ed7 dd hh ll ee ff ff ff ee ff 3 4 4 3 2 4 5 sthx opr store h:x in m (m:m + 1) ? (h:x) 0 dir 35 dd 4 stop enable irq pin; stop oscillator i ? 0; stop oscillator 0 inh 8e 1 stx opr stx opr stx opr ,x stx opr ,x stx ,x stx opr ,sp stx opr ,sp store x in m m ? (x) 0 dir ext ix2 ix1 ix sp1 sp2 bf cf df ef ff 9eef 9edf dd hh ll ee ff ff ff ee ff 3 4 4 3 2 4 5 table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc b0 b7 c central processor unit (cpu) opcode map mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 61 sub # opr sub opr sub opr sub opr ,x sub opr ,x sub ,x sub opr ,sp sub opr ,sp subtract a ? (a) ?(m) imm dir ext ix2 ix1 ix sp1 sp2 a0 b0 c0 d0 e0 f0 9ee0 9ed0 ii dd hh ll ee ff ff ff ee ff 2 3 4 4 3 2 4 5 swi software interrupt pc ? (pc) + 1; push (pcl) sp ? (sp) ?1; push (pch) sp ? (sp) ?1; push (x) sp ? (sp) ?1; push (a) sp ? (sp) ?1; push (ccr) sp ? (sp) ?1; i ? 1 pch ? interrupt vector high byte pcl ? interrupt vector low byte 1 inh 83 9 tap transfer a to ccr ccr ? (a) inh 84 2 tax transfer a to x x ? (a) inh 97 1 tpa transfer ccr to a a ? (ccr) inh 85 1 tst opr tsta tstx tst opr ,x tst ,x tst opr ,sp test for negative or zero (a) ?$00 or (x) ?$00 or (m) ?$00 0 dir inh inh ix1 ix sp1 3d 4d 5d 6d 7d 9e6d dd ff ff 3 1 1 3 2 4 tsx transfer sp to h:x h:x ? (sp) + 1 inh 95 2 txa transfer x to a a ? (x) inh 9f 1 txs transfer h:x to sp (sp) ? (h:x) ?1 inh 94 2 table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 62 central processor unit (cpu) motorola a accumulator n any bit c carry/borrow bit opr operand (one or two bytes) ccr condition code register pc program counter dd direct address of operand pch program counter high byte dd rr direct address of operand and relative offset of branch instruction pcl program counter low byte dd direct to direct addressing mode rel relative addressing mode dir direct addressing mode rel relative program counter offset byte dix+ direct to indexed with post increment addressing mode rr relative program counter offset byte ee ff high and low bytes of offset in indexed, 16-bit offset addressing sp1 stack pointer, 8-bit offset addressing mode ext extended addressing mode sp2 stack pointer 16-bit offset addressing mode ff offset byte in indexed, 8-bit offset addressing sp stack pointer h half-carry bit u unde?ed h index register high byte v over?w bit hh ll high and low bytes of operand address in extended addressing x index register low byte i interrupt mask z zero bit ii immediate operand byte & logical and imd immediate source to direct destination addressing mode | logical or imm immediate addressing mode ? logical exclusive or inh inherent addressing mode ( ) contents of ix indexed, no offset addressing mode ? ) negation (two s complement) ix+ indexed, no offset, post increment addressing mode # immediate value ix+d indexed with post increment to direct addressing mode sign extend ix1 indexed, 8-bit offset addressing mode ? loaded with ix1+ indexed, 8-bit offset, post increment addressing mode ? if ix2 indexed, 16-bit offset addressing mode : concatenated with m memory location set or cleared n negative bit not affected table 6-1. instruction set summary source form operation description effect on ccr address mode opcode operand cycles vh i nzc mc68h(r)c08jl3 ? rev. 4 technical data motorola central processor unit (cpu) 63 central processor unit (cpu) opcode map table 6-2. opcode map bit manipulation branch read-modify-write control register/memory dir dir rel dir inh inh ix1 sp1 ix inh inh imm dir ext ix2 sp2 ix1 sp1 ix 0 1234569e6789 abcd9ede9eef 0 5 brset0 3 dir 4 bset0 2 dir 3 bra 2 rel 4 neg 2 dir 1 nega 1 inh 1 negx 1 inh 4 neg 2 ix1 5 neg 3 sp1 3 neg 1ix 7 rti 1 inh 3 bge 2 rel 2 sub 2 imm 3 sub 2 dir 4 sub 3 ext 4 sub 3 ix2 5 sub 4 sp2 3 sub 2 ix1 4 sub 3 sp1 2 sub 1ix 1 5 brclr0 3 dir 4 bclr0 2 dir 3 brn 2 rel 5 cbeq 3 dir 4 cbeqa 3 imm 4 cbeqx 3 imm 5 cbeq 3 ix1+ 6 cbeq 4 sp1 4 cbeq 2 ix+ 4 rts 1 inh 3 blt 2 rel 2 cmp 2 imm 3 cmp 2 dir 4 cmp 3 ext 4 cmp 3 ix2 5 cmp 4 sp2 3 cmp 2 ix1 4 cmp 3 sp1 2 cmp 1ix 2 5 brset1 3 dir 4 bset1 2 dir 3 bhi 2 rel 5 mul 1 inh 7 div 1 inh 3 nsa 1 inh 2 daa 1 inh 3 bgt 2 rel 2 sbc 2 imm 3 sbc 2 dir 4 sbc 3 ext 4 sbc 3 ix2 5 sbc 4 sp2 3 sbc 2 ix1 4 sbc 3 sp1 2 sbc 1ix 3 5 brclr1 3 dir 4 bclr1 2 dir 3 bls 2 rel 4 com 2 dir 1 coma 1 inh 1 comx 1 inh 4 com 2 ix1 5 com 3 sp1 3 com 1ix 9 swi 1 inh 3 ble 2 rel 2 cpx 2 imm 3 cpx 2 dir 4 cpx 3 ext 4 cpx 3 ix2 5 cpx 4 sp2 3 cpx 2 ix1 4 cpx 3 sp1 2 cpx 1ix 4 5 brset2 3 dir 4 bset2 2 dir 3 bcc 2 rel 4 lsr 2 dir 1 lsra 1 inh 1 lsrx 1 inh 4 lsr 2 ix1 5 lsr 3 sp1 3 lsr 1ix 2 ta p 1 inh 2 txs 1 inh 2 and 2 imm 3 and 2 dir 4 and 3 ext 4 and 3 ix2 5 and 4 sp2 3 and 2 ix1 4 and 3 sp1 2 and 1ix 5 5 brclr2 3 dir 4 bclr2 2 dir 3 bcs 2 rel 4 sthx 2 dir 3 ldhx 3 imm 4 ldhx 2 dir 3 cphx 3 imm 4 cphx 2 dir 1 tpa 1 inh 2 tsx 1 inh 2 bit 2 imm 3 bit 2 dir 4 bit 3 ext 4 bit 3 ix2 5 bit 4 sp2 3 bit 2 ix1 4 bit 3 sp1 2 bit 1ix 6 5 brset3 3 dir 4 bset3 2 dir 3 bne 2 rel 4 ror 2 dir 1 rora 1 inh 1 rorx 1 inh 4 ror 2 ix1 5 ror 3 sp1 3 ror 1ix 2 pula 1 inh 2 lda 2 imm 3 lda 2 dir 4 lda 3 ext 4 lda 3 ix2 5 lda 4 sp2 3 lda 2 ix1 4 lda 3 sp1 2 lda 1ix 7 5 brclr3 3 dir 4 bclr3 2 dir 3 beq 2 rel 4 asr 2 dir 1 asra 1 inh 1 asrx 1 inh 4 asr 2 ix1 5 asr 3 sp1 3 asr 1ix 2 psha 1 inh 1 ta x 1 inh 2 ais 2 imm 3 sta 2 dir 4 sta 3 ext 4 sta 3 ix2 5 sta 4 sp2 3 sta 2 ix1 4 sta 3 sp1 2 sta 1ix 8 5 brset4 3 dir 4 bset4 2 dir 3 bhcc 2 rel 4 lsl 2 dir 1 lsla 1 inh 1 lslx 1 inh 4 lsl 2 ix1 5 lsl 3 sp1 3 lsl 1ix 2 pulx 1 inh 1 clc 1 inh 2 eor 2 imm 3 eor 2 dir 4 eor 3 ext 4 eor 3 ix2 5 eor 4 sp2 3 eor 2 ix1 4 eor 3 sp1 2 eor 1ix 9 5 brclr4 3 dir 4 bclr4 2 dir 3 bhcs 2 rel 4 rol 2 dir 1 rola 1 inh 1 rolx 1 inh 4 rol 2 ix1 5 rol 3 sp1 3 rol 1ix 2 pshx 1 inh 1 sec 1 inh 2 adc 2 imm 3 adc 2 dir 4 adc 3 ext 4 adc 3 ix2 5 adc 4 sp2 3 adc 2 ix1 4 adc 3 sp1 2 adc 1ix a 5 brset5 3 dir 4 bset5 2 dir 3 bpl 2 rel 4 dec 2 dir 1 deca 1 inh 1 decx 1 inh 4 dec 2 ix1 5 dec 3 sp1 3 dec 1ix 2 pulh 1 inh 2 cli 1 inh 2 ora 2 imm 3 ora 2 dir 4 ora 3 ext 4 ora 3 ix2 5 ora 4 sp2 3 ora 2 ix1 4 ora 3 sp1 2 ora 1ix b 5 brclr5 3 dir 4 bclr5 2 dir 3 bmi 2 rel 5 dbnz 3 dir 3 dbnza 2 inh 3 dbnzx 2 inh 5 dbnz 3 ix1 6 dbnz 4 sp1 4 dbnz 2ix 2 pshh 1 inh 2 sei 1 inh 2 add 2 imm 3 add 2 dir 4 add 3 ext 4 add 3 ix2 5 add 4 sp2 3 add 2 ix1 4 add 3 sp1 2 add 1ix c 5 brset6 3 dir 4 bset6 2 dir 3 bmc 2 rel 4 inc 2 dir 1 inca 1 inh 1 incx 1 inh 4 inc 2 ix1 5 inc 3 sp1 3 inc 1ix 1 clrh 1 inh 1 rsp 1 inh 2 jmp 2 dir 3 jmp 3 ext 4 jmp 3 ix2 3 jmp 2 ix1 2 jmp 1ix d 5 brclr6 3 dir 4 bclr6 2 dir 3 bms 2 rel 3 tst 2 dir 1 tsta 1 inh 1 tstx 1 inh 3 tst 2 ix1 4 tst 3 sp1 2 tst 1ix 1 nop 1 inh 4 bsr 2 rel 4 jsr 2 dir 5 jsr 3 ext 6 jsr 3 ix2 5 jsr 2 ix1 4 jsr 1ix e 5 brset7 3 dir 4 bset7 2 dir 3 bil 2 rel 5 mov 3dd 4 mov 2 dix+ 4 mov 3 imd 4 mov 2 ix+d 1 stop 1 inh * 2 ldx 2 imm 3 ldx 2 dir 4 ldx 3 ext 4 ldx 3 ix2 5 ldx 4 sp2 3 ldx 2 ix1 4 ldx 3 sp1 2 ldx 1ix f 5 brclr7 3 dir 4 bclr7 2 dir 3 bih 2 rel 3 clr 2 dir 1 clra 1 inh 1 clrx 1 inh 3 clr 2 ix1 4 clr 3 sp1 2 clr 1ix 1 wait 1 inh 1 txa 1 inh 2 aix 2 imm 3 stx 2 dir 4 stx 3 ext 4 stx 3 ix2 5 stx 4 sp2 3 stx 2 ix1 4 stx 3 sp1 2 stx 1ix inh inherent rel relative sp1 stack pointer, 8-bit offset imm immediate ix indexed, no offset sp2 stack pointer, 16-bit offset dir direct ix1 indexed, 8-bit offset ix+ indexed, no offset with ext extended ix2 indexed, 16-bit offset post increment dd direct-direct imd immediate-direct ix1+ indexed, 1-byte offset with ix+d indexed-direct dix+ direct-indexed post increment * pre-byte for stack pointer indexed instructions 0 high byte of opcode in hexadecimal low byte of opcode in hexadecimal 0 5 brset0 3 dir cycles opcode mnemonic number of bytes / addressing mode msb lsb msb lsb central processor unit (cpu) technical data mc68h(r)c08jl3 ? rev. 4 64 central processor unit (cpu) motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 65 technical data ?mc68h(r)c08jl3 section 7. system integration module (sim) 7.1 contents 7.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 7.3 sim bus clock control and generation . . . . . . . . . . . . . . . . . . 69 7.3.1 bus timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 7.3.2 clock start-up from por . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 7.3.3 clocks in stop mode and wait mode . . . . . . . . . . . . . . . . . . 69 7.4 reset and system initialization. . . . . . . . . . . . . . . . . . . . . . . . . 70 7.4.1 external pin reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 7.4.2 active resets from internal sources . . . . . . . . . . . . . . . . . . 71 7.4.2.1 power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 7.4.2.2 computer operating properly (cop) reset . . . . . . . . . . 73 7.4.2.3 illegal opcode reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 7.4.2.4 illegal address reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 7.4.2.5 lvi reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 7.5 sim counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 7.5.1 sim counter during power-on reset . . . . . . . . . . . . . . . . . 74 7.5.2 sim counter during stop mode recovery . . . . . . . . . . . . . . 74 7.5.3 sim counter and reset states. . . . . . . . . . . . . . . . . . . . . . . 75 7.6 exception control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 7.6.1 interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 7.6.1.1 hardware interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 7.6.1.2 swi instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 7.6.2 interrupt status registers. . . . . . . . . . . . . . . . . . . . . . . . . . . 79 7.6.2.1 interrupt status register 1 . . . . . . . . . . . . . . . . . . . . . . . 80 7.6.2.2 interrupt status register 2 . . . . . . . . . . . . . . . . . . . . . . . . 80 7.6.2.3 interrupt status register 3 . . . . . . . . . . . . . . . . . . . . . . . . 81 7.6.3 reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 7.6.4 break interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 7.6.5 status flag protection in break mode . . . . . . . . . . . . . . . . . 81 system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 66 system integration module (sim) motorola 7.7 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 7.7.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 7.7.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 7.8 sim registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 7.8.1 break status register (bsr) . . . . . . . . . . . . . . . . . . . . . . . . 85 7.8.2 reset status register (rsr) . . . . . . . . . . . . . . . . . . . . . . . . 86 7.8.3 break flag control register (bfcr) . . . . . . . . . . . . . . . . . . 88 7.2 introduction this section describes the system integration module (sim), which supports up to 24 external and/or internal interrupts. together with the cpu, the sim controls all mcu activities. a block diagram of the sim is shown in figure 7-1 . figure 7-2 is a summary of the sim i/o registers. the sim is a system state controller that coordinates cpu and exception timing. the sim is responsible for: bus clock generation and control for cpu and peripherals stop/wait/reset/break entry and recovery internal clock control master reset control, including power-on reset (por) and cop timeout interrupt control: acknowledge timing arbitration control timing vector address generation cpu enable/disable timing modular architecture expandable to 128 interrupt sources system integration module (sim) introduction mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 67 figure 7-1. sim block diagram table 7-1. signal name conventions signal name description 2oscout buffered clock from the x-tal oscillator circuit or the rc oscillator circuit. oscout the 2oscout frequency divided by two. this signal is again divided by two in the sim to generate the internal bus clocks. (bus clock = 2oscout ?4) iab internal address bus idb internal data bus porrst signal from the power-on reset module to the sim irst internal reset signal r/w read/write signal stop/wait clock control clock generators por control reset pin control sim reset status register interrupt control and priority decode module stop module wait cpu stop (from cpu) cpu wait (from cpu) simoscen (to oscillator) oscout (from oscillator) internal clocks master reset control reset pin logic illegal opcode (from cpu) illegal address (from address map decoders) cop timeout (from cop module) interrupt sources cpu interface reset control sim counter cop clock 2oscout (from oscillator) ? 2 usb reset (from usb module) vdd internal pull-up system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 68 system integration module (sim) motorola addr. register name bit 7 654321 bit 0 $fe00 break status register (bsr) read: rrrrrr sbsw r write: note reset: 00000000 note: writing a logic 0 clears sbsw. $fe01 reset status register (rsr) read: por pin cop ilop ilad modrst lvi 0 write: por: 10000000 $fe02 reserved read: rrrrrrrr write: reset: $fe03 break flag control register (bfcr) read: bcfe rrrrrrr write: reset: 0 $fe04 interrupt status register 1 (int1) read: 0 if5 if4 if3 0 if1 0 0 write: rrrrrrrr reset: 00000000 $fe05 interrupt status register 2 (int2) read: if14 0000000 write: rrrrrrrr reset: 00000000 $fe06 interrupt status register 3 (int3) read: 0000000 if15 write: rrrrrrrr reset: 00000000 = unimplemented r = reserved figure 7-2. sim i/o register summary system integration module (sim) sim bus clock control and generation mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 69 7.3 sim bus clock control and generation the bus clock generator provides system clock signals for the cpu and peripherals on the mcu. the system clocks are generated from an incoming clock, oscout, as shown in figure 7-3 . figure 7-3. sim clock signals 7.3.1 bus timing in user mode , the internal bus frequency is the oscillator frequency (2oscout) divided by four. 7.3.2 clock start-up from por when the power-on reset module generates a reset, the clocks to the cpu and peripherals are inactive and held in an inactive phase until after the 4096 2oscout cycle por time-out has completed. the rst pin is driven low by the sim during this entire period. the ibus clocks start upon completion of the time-out. 7.3.3 clocks in stop mode and wait mode upon exit from stop mode by an interrupt, break, or reset, the sim allows 2oscout to clock the sim counter. the cpu and peripheral clocks do not become active until after the stop delay time-out. this time-out is selectable as 4096 or 32 2oscout cycles. (see 7.7.2 stop mode .) ? 2 bus clock generators sim sim counter from oscillator from oscillator oscout 2oscout system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 70 system integration module (sim) motorola in wait mode, the cpu clocks are inactive. the sim also produces two sets of clocks for other modules. refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode. some modules can be programmed to be active in wait mode. 7.4 reset and system initialization the mcu has these reset sources: power-on reset module (por) external reset pin (rst ) computer operating properly module (cop) low-voltage inhibit module (lvi) illegal opcode illegal address all of these resets produce the vector $fffe?fff ($fefe?eff in monitor mode) and assert the internal reset signal (irst). irst causes all registers to be returned to their default values and all modules to be returned to their reset states. an internal reset clears the sim counter (see 7.5 sim counter ), but an external reset does not. each of the resets sets a corresponding bit in the reset status register (rsr). (see 7.8 sim registers .) 7.4.1 external pin reset the rst pin circuits include an internal pull-up device. pulling the asynchronous rst pin low halts all processing. the pin bit of the reset status register (rsr) is set as long as rst is held low for a minimum of 67 2oscclk cycles, assuming that the por was not the source of the reset. see table 7-2 for details. figure 7-4 shows the relative timing. table 7-2. pin bit set timing reset type number of cycles required to set pin por 4163 (4096 + 64 + 3) all others 67 (64 + 3) system integration module (sim) reset and system initialization mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 71 figure 7-4. external reset timing 7.4.2 active resets from internal sources all internal reset sources actively pull the rst pin low for 32 2oscout cycles to allow resetting of external peripherals. the internal reset signal irst continues to be asserted for an additional 32 cycles ( figure 7-5 ). an internal reset can be caused by an illegal address, illegal opcode, cop time-out, or por. (see figure 7-6 . sources of internal reset .) note that for por resets, the sim cycles through 4096 2oscout cycles during which the sim forces the rst pin low. the internal reset signal then follows the sequence from the falling edge of rst shown in figure 7-5 . figure 7-5. internal reset timing the cop reset is asynchronous to the bus clock. figure 7-6. sources of internal reset rst iab pc vect h vect l oscout irst rst r s t pulled low by mcu iab 32 cycles 32 cycles vector high 2oscout illegal address rst illegal opcode rst coprst por lvi internal reset system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 72 system integration module (sim) motorola the active reset feature allows the part to issue a reset to peripherals and other chips within a system built around the mcu. 7.4.2.1 power-on reset when power is first applied to the mcu, the power-on reset module (por) generates a pulse to indicate that power-on has occurred. the external reset pin (rst ) is held low while the sim counter counts out 4096 2oscout cycles. sixty-four 2oscout cycles later, the cpu and memories are released from reset to allow the reset vector sequence to occur. at power-on, the following events occur: a por pulse is generated. the internal reset signal is asserted. the sim enables the oscillator to drive 2oscout. internal clocks to the cpu and modules are held inactive for 4096 2oscout cycles to allow stabilization of the oscillator. the rst pin is driven low during the oscillator stabilization time. the por bit of the reset status register (rsr) is set and all other bits in the register are cleared. figure 7-7. por recovery porrst osc1 2oscout oscout rst iab 4096 cycles 32 cycles 32 cycles $fffe $ffff system integration module (sim) reset and system initialization mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 73 7.4.2.2 computer operating properly (cop) reset an input to the sim is reserved for the cop reset signal. the overflow of the cop counter causes an internal reset and sets the cop bit in the reset status register (rsr). the sim actively pulls down the rst pin for all internal reset sources. to prevent a cop module time-out, write any value to location $ffff. writing to location $ffff clears the cop counter and stages 12 through 5 of the sim counter. the sim counter output, which occurs at least every (2 12 ?2 4 ) 2oscout cycles, drives the cop counter. the cop should be serviced as soon as possible out of reset to guarantee the maximum amount of time before the first time-out. the cop module is disabled if the rst pin or the irq 1 pin is held at v dd + v hi while the mcu is in monitor mode. the cop module can be disabled only through combinational logic conditioned with the high voltage signal on the rst or the irq1 pin. this prevents the cop from becoming disabled as a result of external noise. during a break state, v dd + v hi on the rst pin disables the cop module. 7.4.2.3 illegal opcode reset the sim decodes signals from the cpu to detect illegal instructions. an illegal instruction sets the ilop bit in the reset status register (rsr) and causes a reset. if the stop enable bit, stop, in the mask option register is logic zero, the sim treats the stop instruction as an illegal opcode and causes an illegal opcode reset. the sim actively pulls down the rst pin for all internal reset sources. 7.4.2.4 illegal address reset an opcode fetch from an unmapped address generates an illegal address reset. the sim verifies that the cpu is fetching an opcode prior to asserting the ilad bit in the reset status register (rsr) and resetting the mcu. a data fetch from an unmapped address does not generate a reset. the sim actively pulls down the rst pin for all internal reset sources. system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 74 system integration module (sim) motorola 7.4.2.5 lvi reset the low-voltage inhibit module (lvi) asserts its output to the sim when the v dd voltage falls to the lvi trip voltage v trip . the lvi bit in the sim reset status register (srsr) is set, and the external reset pin (rstb) is held low while the sim counter counts out 4096 2oscclk cycles. sixty- four 2oscout cycles later, the cpu and memories are released from reset to allow the reset vector sequence to occur. the sim actively pulls down the (rstb) pin for all internal reset sources. 7.5 sim counter the sim counter is used by the power-on reset module (por) and in stop mode recovery to allow the oscillator time to stabilize before enabling the internal bus (ibus) clocks. the sim counter also serves as a prescaler for the computer operating properly module (cop). the sim counter uses 12 stages for counting, followed by a 13th stage that triggers a reset of sim counters and supplies the clock for the cop module. the sim counter is clocked by the falling edge of 2oscout. 7.5.1 sim counter during power-on reset the power-on reset module (por) detects power applied to the mcu. at power-on, the por circuit asserts the signal porrst. once the sim is initialized, it enables the oscillator to drive the bus clock state machine. 7.5.2 sim counter during stop mode recovery the sim counter also is used for stop mode recovery. the stop instruction clears the sim counter. after an interrupt, break, or reset, the sim senses the state of the short stop recovery bit, ssrec, in the mask option register. if the ssrec bit is a logic one, then the stop recovery is reduced from the normal delay of 4096 2oscout cycles down to 32 2oscout cycles. this is ideal for applications using canned oscillators that do not require long start-up times from stop mode. external crystal applications should use the full stop recovery time, that is, with ssrec cleared in the configuration register (config). system integration module (sim) exception control mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 75 7.5.3 sim counter and reset states external reset has no effect on the sim counter. (see 7.7.2 stop mode for details.) the sim counter is free-running after all reset states. (see 7.4.2 active resets from internal sources for counter control and internal reset recovery sequences.) 7.6 exception control normal, sequential program execution can be changed in three different ways: interrupts maskable hardware cpu interrupts non-maskable software interrupt instruction (swi) reset break interrupts 7.6.1 interrupts an interrupt temporarily changes the sequence of program execution to respond to a particular event. figure 7-8 flow charts the handling of system interrupts. interrupts are latched, and arbitration is performed in the sim at the start of interrupt processing. the arbitration result is a constant that the cpu uses to determine which vector to fetch. once an interrupt is latched by the sim, no other interrupt can take precedence, regardless of priority, until the latched interrupt is serviced (or the i bit is cleared). system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 76 system integration module (sim) motorola figure 7-8. interrupt processing no no no yes no no yes no yes yes (as many interrupts as exist on chip) i bit set? from reset break interrupt? i bit set? irq interrupt? timer interrupt? swi instruction? rti instruction? fetch next instruction unstack cpu registers. stack cpu registers. set i bit. load pc with interrupt vector. execute instruction. yes yes system integration module (sim) exception control mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 77 at the beginning of an interrupt, the cpu saves the cpu register contents on the stack and sets the interrupt mask (i bit) to prevent additional interrupts. at the end of an interrupt, the rti instruction recovers the cpu register contents from the stack so that normal processing can resume. figure 7-9 shows interrupt entry timing. figure 7-10 shows interrupt recovery timing. figure 7-9 . interrupt entry figure 7-10. interrupt recovery 7.6.1.1 hardware interrupts a hardware interrupt does not stop the current instruction. processing of a hardware interrupt begins after completion of the current instruction. when the current instruction is complete, the sim checks all pending hardware interrupts. if interrupts are not masked (i bit clear in the condition code register), and if the corresponding interrupt enable bit is module idb r/w interrupt dummy sp sp ?1 sp ?2 sp ?3 sp ?4 vect h vect l start addr iab dummy pc ?1[7:0] pc ?1[15:8] x a ccr v data h v data l opcode i bit module idb r/w interrupt sp ?4 sp ?3 sp ?2 sp ?1 sp pc pc + 1 iab ccr a x pc ?1[7:0] pc ?1[15:8] opcode operand i bit system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 78 system integration module (sim) motorola set, the sim proceeds with interrupt processing; otherwise, the next instruction is fetched and executed. if more than one interrupt is pending at the end of an instruction execution, the highest priority interrupt is serviced first. figure 7-11 demonstrates what happens when two interrupts are pending. if an interrupt is pending upon exit from the original interrupt service routine, the pending interrupt is serviced before the lda instruction is executed. figure 7-11 . interrupt recognition example the lda opcode is prefetched by both the int1 and int2 rti instructions. however, in the case of the int1 rti prefetch, this is a redundant operation. note: to maintain compatibility with the m6805 family, the h register is not pushed on the stack during interrupt entry. if the interrupt service routine modifies the h register or uses the indexed addressing mode, software should save the h register and then restore it prior to exiting the routine. cli lda int1 pulh rti int2 background routine #$ff pshh int1 interrupt service routine pulh rti pshh int2 interrupt service routine system integration module (sim) exception control mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 79 7.6.1.2 swi instruction the swi instruction is a non-maskable instruction that causes an interrupt regardless of the state of the interrupt mask (i bit) in the condition code register. note: a software interrupt pushes pc onto the stack. a software interrupt does not push pc ?1, as a hardware interrupt does. 7.6.2 interrupt status registers the flags in the interrupt status registers identify maskable interrupt sources. table 7-3 summarizes the interrupt sources and the interrupt status register flags that they set. the interrupt status registers can be useful for debugging. table 7-3. interrupt sources priority source flag mask 1 int register flag vector address highest reset $fffe?ffff swi instruction $fffc?fffd irq 1 pin irqf1 imask1 if1 $fffa?fffb timer channel 0 interrupt ch0f ch0ie if3 $fff6?fff7 timer channel 1 interrupt ch1f ch1ie if4 $fff4?fff5 timer over?w interrupt tof toie if5 $fff2?fff3 keyboard interrupt keyf imaskk if14 $ffe0?ffe1 lowest adc conversion complete interrupt coco aien if15 $ffde?ffdf note: 1. the i bit in the condition code register is a global mask for all interrupts sources except the swi instruction. system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 80 system integration module (sim) motorola 7.6.2.1 interrupt status register 1 i f 1, i f 3 to if5 ?interrupt flags these flags indicate the presence of interrupt requests from the sources shown in table 7-3 . 1 = interrupt request present 0 = no interrupt request present bit 0, 1, 3 and 7 ?always read 0 7.6.2.2 interrupt status register 2 i f 14 ?interrupt flags this flag indicates the presence of interrupt requests from the sources shown in table 7-3 . 1 = interrupt request present 0 = no interrupt request present bit 0 to 6 ?always read 0 address: $fe04 bit 7 654321 bit 0 read: 0 if5 if4 if3 0 if1 0 0 write: rrrrrrrr reset: 00000000 r = reserved figure 7-12. interrupt status register 1 (int1) address: $fe05 bit 7 654321 bit 0 read: if14 0000000 write: rrrrrrrr reset: 00000000 r = reserved figure 7-13. interrupt status register 2 (int2) system integration module (sim) exception control mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 81 7.6.2.3 interrupt status register 3 i f 15 ?interrupt flags these flags indicate the presence of interrupt requests from the sources shown in table 7-3 . 1 = interrupt request present 0 = no interrupt request present bit 1 to 7 ?always read 0 7.6.3 reset all reset sources always have equal and highest priority and cannot be arbitrated. 7.6.4 break interrupts the break module can stop normal program flow at a software- programmable break point by asserting its break interrupt output. (see section 17. break module (break) .) the sim puts the cpu into the break state by forcing it to the swi vector location. refer to the break interrupt subsection of each module to see how each module is affected by the break state. 7.6.5 status flag protection in break mode the sim controls whether status flags contained in other modules can be cleared during break mode. the user can select whether flags are address: $fe06 bit 7 654321 bit 0 read: 0000000 if15 write: rrrrrrrr reset: 00000000 r = reserved figure 7-14. interrupt status register 3 (int3) system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 82 system integration module (sim) motorola protected from being cleared by properly initializing the break clear flag enable bit (bcfe) in the break flag control register (bfcr). protecting flags in break mode ensures that set flags will not be cleared while in break mode. this protection allows registers to be freely read and written during break mode without losing status flag information. setting the bcfe bit enables the clearing mechanisms. once cleared in break mode, a flag remains cleared even when break mode is exited. status flags with a two-step clearing mechanism ?for example, a read of one register followed by the read or write of another ?are protected, even when the first step is accomplished prior to entering break mode. upon leaving break mode, execution of the second step will clear the flag as normal. 7.7 low-power modes executing the wait or stop instruction puts the mcu in a low-power- consumption mode for standby situations. the sim holds the cpu in a non-clocked state. the operation of each of these modes is described below. both stop and wait clear the interrupt mask (i) in the condition code register, allowing interrupts to occur. 7.7.1 wait mode in wait mode, the cpu clocks are inactive while the peripheral clocks continue to run. figure 7-15 shows the timing for wait mode entry. a module that is active during wait mode can wake up the cpu with an interrupt if the interrupt is enabled. stacking for the interrupt begins one cycle after the wait instruction during which the interrupt occurred. in wait mode, the cpu clocks are inactive. refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode. some modules can be programmed to be active in wait mode. wait mode can also be exited by a reset or break. a break interrupt during wait mode sets the sim break stop/wait bit, sbsw, in the break system integration module (sim) low-power modes mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 83 status register (bsr). if the cop disable bit, copd, in the mask option register is logic zero, then the computer operating properly module (cop) is enabled and remains active in wait mode. figure 7-15. wait mode entry timing figure 7-16 and figure 7-17 show the timing for wait recovery. figure 7-16. wait recovery from interrupt or break figure 7-17. wait recovery from internal reset wait addr + 1 same same iab idb previous data next opcode same wait addr same r/w note: previous data can be operand data or the wait opcode, depending on the last instruction. $6e0c $6e0b $00ff $00fe $00fd $00fc $a6 $a6 $01 $0b $6e $a6 iab idb exitstopwait note: exitstopwait = rst pin or cpu interrupt or break interrupt iab idb rst $a6 $a6 $6e0b rst vct h rst vct l $a6 2oscout 32 cycles 32 cycles system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 84 system integration module (sim) motorola 7.7.2 stop mode in stop mode, the sim counter is reset and the system clocks are disabled. an interrupt request from a module can cause an exit from stop mode. stacking for interrupts begins after the selected stop recovery time has elapsed. reset or break also causes an exit from stop mode. the sim disables the oscillator signals (oscout and 2oscout) in stop mode, stopping the cpu and peripherals. stop recovery time is selectable using the ssrec bit in the configuration register (config). if ssrec is set, stop recovery is reduced from the normal delay of 4096 2oscout cycles down to 32. this is ideal for applications using canned oscillators that do not require long start-up times from stop mode. note: external crystal applications should use the full stop recovery time by clearing the ssrec bit. a break interrupt during stop mode sets the sim break stop/wait bit (sbsw) in the break status register (bsr). the sim counter is held in reset from the execution of the stop instruction until the beginning of stop recovery. it is then used to time the recovery period. figure 7-18 shows stop mode entry timing. note: to minimize stop current, all pins configured as inputs should be driven to a logic 1 or logic 0. figure 7-18. stop mode entry timing stop addr + 1 same same iab idb previous data next opcode same stop addr same r/w cpustop note: previous data can be operand data or the stop opcode, depending on the last instruction. system integration module (sim) sim registers mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 85 figure 7-19. stop mode recovery from interrupt or break 7.8 sim registers the sim has three memory mapped registers. table 7-4 shows the mapping of these registers. 7.8.1 break status register (bsr) the break status register contains a flag to indicate that a break caused an exit from stop or wait mode. 2oscout int/break iab stop + 2 stop + 2 sp sp ?1 sp ?2 sp ?3 stop +1 stop recovery period table 7-4. sim registers address register access mode $fe00 bsr user $fe01 rsr user $fe03 bfcr user address: $fe00 bit 7 654321 bit 0 read: rrrrrr sbsw r write: note (1) reset: 0 r = reserved 1. writing a logic zero clears sbsw. figure 7-20. break status register (bsr) system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 86 system integration module (sim) motorola sbsw ?sim break stop/wait this status bit is useful in applications requiring a return to wait or stop mode after exiting from a break interrupt. clear sbsw by writing a logic zero to it. reset clears sbsw. 1 = stop mode or wait mode was exited by break interrupt 0 = stop mode or wait mode was not exited by break interrupt sbsw can be read within the break state swi routine. the user can modify the return address on the stack by subtracting one from it. the following code is an example of this. writing zero to the sbsw bit clears it. 7.8.2 reset status register (rsr) this register contains six flags that show the source of the last reset. clear the sim reset status register by reading it. a power-on reset sets the por bit and clears all other bits in the register. ; ; ; this code works if the h register has been pushed onto the stack in the break service routine software. this code should be executed at the end of the break service routine software. hibyte equ 5 lobyte equ 6 ; if not sbsw, do rti brclr sbsw,bsr, return ; ; see if wait mode or stop mode was exited by break. tst lobyte,sp ; if returnlo is not zero, bne dolo ; then just decrement low byte. dec hibyte,sp ; else deal with high byte, too. dolo dec lobyte,sp ; point to wait/stop opcode. return pulh rti ; restore h register. system integration module (sim) sim registers mc68h(r)c08jl3 ? rev. 4 technical data motorola system integration module (sim) 87 por ?power-on reset bit 1 = last reset caused by por circuit 0 = read of srsr pin ?external reset bit 1 = last reset caused by external reset pin (rst ) 0 = por or read of srsr cop ?computer operating properly reset bit 1 = last reset caused by cop counter 0 = por or read of srsr ilop ?illegal opcode reset bit 1 = last reset caused by an illegal opcode 0 = por or read of srsr ilad ?illegal address reset bit (opcode fetches only) 1 = last reset caused by an opcode fetch from an illegal address 0 = por or read of srsr modrst ?monitor mode entry module reset bit 1 = last reset caused by monitor mode entry when vector locations $fffe and $ffff are $00 after por while irqb = v dd 0 = por or read of srsr lvi ?low voltage inhibit reset bit 1 = last reset caused by lvi circuit 0 = por or read of srsr address: $fe01 bit 7 654321 bit 0 read: por pin cop ilop ilad modrst lvi 0 write: por: 10000000 = unimplemented figure 7-21. reset status register (rsr) system integration module (sim) technical data mc68h(r)c08jl3 ? rev. 4 88 system integration module (sim) motorola 7.8.3 break flag control register (bfcr) the break control register contains a bit that enables software to clear status bits while the mcu is in a break state. bcfe ?break clear flag enable bit this read/write bit enables software to clear status bits by accessing status registers while the mcu is in a break state. to clear status bits during the break state, the bcfe bit must be set. 1 = status bits clearable during break 0 = status bits not clearable during break address: $fe03 bit 7 654321 bit 0 read: bcfe rrrrrrr write: reset: 0 r = reserved figure 7-22. break flag control register (bfcr) mc68h(r)c08jl3 ? rev. 4 technical data motorola oscillator (osc) 89 technical data ?mc68h(r)c08jl3 section 8. oscillator (osc) 8.1 contents 8.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 8.3 x-tal oscillator (mc68hc08xxx). . . . . . . . . . . . . . . . . . . . . . . . 90 8.4 rc oscillator (mc68hrc08xxx) . . . . . . . . . . . . . . . . . . . . . . . 91 8.5 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 8.5.1 crystal amplifier input pin (osc1). . . . . . . . . . . . . . . . . . . . 92 8.5.2 crystal amplifier output pin (osc2/pta6/rcclk). . . . . . . 92 8.5.3 oscillator enable signal (simoscen). . . . . . . . . . . . . . . . . 92 8.5.4 x-tal oscillator clock (xtalclk). . . . . . . . . . . . . . . . . . . . . 92 8.5.5 rc oscillator clock (rcclk). . . . . . . . . . . . . . . . . . . . . . . . 93 8.5.6 oscillator out 2 (2oscout) . . . . . . . . . . . . . . . . . . . . . . . . 93 8.5.7 oscillator out (oscout). . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.6 low power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.7 oscillator during break mode. . . . . . . . . . . . . . . . . . . . . . . . . . 94 8.2 introduction the oscillator module provides the reference clock for the mcu system and bus. two types of oscillator modules are available: mc68hc08xxx?built-in oscillator module (x-tal oscillator) that requires an external crystal or ceramic-resonator. this option also allows an external clock that can be driven directly into osc1. mc68hrc08xxx ?built-in oscillator module (rc oscillator) that requires an external rc connection only. oscillator (osc) technical data mc68h(r)c08jl3 ? rev. 4 90 oscillator (osc) motorola 8.3 x-tal oscillator (mc68hc08xxx) the x-tal oscillator circuit is designed for use with an external crystal or ceramic resonator to provide accurate clock source. in its typical configuration, the x-tal oscillator is connected in a pierce oscillator configuration, as shown in figure 8-1 . this figure shows only the logical representation of the internal components and may not represent actual circuitry. the oscillator configuration uses five components: crystal, x 1 fixed capacitor, c 1 tuning capacitor, c 2 (can also be a fixed capacitor) feedback resistor, r b series resistor, r s (optional) figure 8-1. x-tal oscillator external connections c 1 c 2 simoscen xtalclk r b x 1 r s * *r s can be zero (shorted) when used with higher-frequency crystals. mcu from sim refer to manufacturer? data. osc2 osc1 ?2 oscout 2oscout to sim to sim see section 18. for component value requirements. oscillator (osc) rc oscillator (mc68hrc08xxx) mc68h(r)c08jl3 ? rev. 4 technical data motorola oscillator (osc) 91 the series resistor (r s ) is included in the diagram to follow strict pierce oscillator guidelines and may not be required for all ranges of operation, especially with high frequency crystals. refer to the crystal manufacturer? data for more information. 8.4 rc oscillator (mc68hrc08xxx) the rc oscillator circuit is designed for use with external r and c to provide a clock source with tolerance less than 10%. in its typical configuration, the rc oscillator requires two external components, one r and one c. component values should have a tolerance of 1% or less, to obtain a clock source with less than 10% tolerance. the oscillator configuration uses two components: ? ext ? ext figure 8-2. rc oscillator external connections mcu r ext c ext simoscen osc1 ext-rc oscillator en rcclk ?2 oscout 2oscout to sim from sim v dd pta6 i/o 0 1 pta6 pta6en pta6/rcclk (osc2) to sim see section 18. for component value requirements. oscillator (osc) technical data mc68h(r)c08jl3 ? rev. 4 92 oscillator (osc) motorola 8.5 i/o signals the following paragraphs describe the oscillator i/o signals. 8.5.1 crystal amplifier input pin (osc1) osc1 pin is an input to the crystal oscillator amplifier or the input to the rc oscillator circuit. 8.5.2 crystal amplifier output pin (osc2/pta6/rcclk) for the x-tal oscillator device , osc2 pin is the output of the crystal oscillator inverting amplifier. for the rc oscillator device, osc2 pin can be configured as a general purpose i/o pin pta6, or the output of the internal rc oscillator clock, rcclk. 8.5.3 oscillator enable signal (simoscen) the simoscen signal comes from the system integration module (sim) and enables/disables the x-tal oscillator circuit or the rc-oscillator. 8.5.4 x-tal oscillator clock (xtalclk) xtalclk is the x-tal oscillator output signal. it runs at the full speed of the crystal (f xclk ) and comes directly from the crystal oscillator circuit. figure 8-1 shows only the logical relation of xtalclk to osc1 and osc2 and may not represent the actual circuitry. the duty cycle of xtalclk is unknown and may depend on the crystal and other external factors. also, the frequency and amplitude of xtalclk can be unstable at start-up. option osc2 pin function x-tal oscillator inverting osc1 rc oscillator controlled by ptaen bit in ptapuer ($0d) pta6en = 0: rcclk output pta6en = 1: pta6 i/o oscillator (osc) low power modes mc68h(r)c08jl3 ? rev. 4 technical data motorola oscillator (osc) 93 8.5.5 rc oscillator clock (rcclk) rcclk is the rc oscillator output signal. its frequency is directly proportional to the time constant of the external r and c. figure 8-2 shows only the logical relation of rcclk to osc1 and may not represent the actual circuitry. 8.5.6 oscillator out 2 (2oscout) 2oscout is same as the input clock (xtalclk or rcclk). this signal is driven to the sim module and is used to determine the cop cycles. 8.5.7 oscillator out (oscout) the frequency of this signal is equal to half of the 2oscout, this signal is driven to the sim for generation of the bus clocks used by the cpu and other modules on the mcu. oscout will be divided again in the sim and results in the internal bus frequency being one fourth of the xtalclk or rcclk frequency. 8.6 low power modes the wait and stop instructions put the mcu in low-power consumption standby modes. 8.6.1 wait mode the wait instruction has no effect on the oscillator logic. oscout and 2oscout continues to drive to the sim module. 8.6.2 stop mode the stop instruction disables the xtalclk or the rcclk output, hence oscout and 2oscout. oscillator (osc) technical data mc68h(r)c08jl3 ? rev. 4 94 oscillator (osc) motorola 8.7 oscillator during break mode the oscillator continues to drive oscout and 2oscout when the device enters the break state. mc68h(r)c08jl3 ? rev. 4 technical data motorola monitor rom (mon) 95 technical data ?mc68h(r)c08jl3 section 9. monitor rom (mon) 9.1 contents 9.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 9.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 9.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 9.4.1 entering monitor mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 9.4.2 baud rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9.4.3 data format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9.4.4 echoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 9.4.5 break signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 9.4.6 commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 9.2 introduction this section describes the monitor rom (mon). the monitor rom allows complete testing of the mcu through a single-wire interface with a host computer. monitor rom (mon) technical data mc68h(r)c08jl3 ? rev. 4 96 monitor rom (mon) motorola 9.3 features features of the monitor rom include the following: normal user-mode pin functionality one pin dedicated to serial communication between monitor rom and host computer standard mark/space non-return-to-zero (nrz) communication with host computer 4800 baud to 28.8 k-baud communication with host computer execution of code in ram or rom 9.4 functional description the monitor rom receives and executes commands from a host computer. figure 9-1 shows a example circuit used to enter monitor mode and communicate with a host computer via a standard rs-232 interface. while simple monitor commands can access any memory address, the mcu has a rom security feature that requires proper procedures to be followed before the rom can be accessed. access to the rom is denied to unauthorized users of customer-specified software. in monitor mode, the mcu can execute host-computer code in ram while all mcu pins except ptb0 retain normal operating mode functions. all communication between the host computer and the mcu is through the ptb0 pin. a level-shifting and multiplexing interface is required between ptb0 and the host computer. ptb0 is used in a wired-or configuration and requires a pull-up resistor. monitor rom (mon) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola monitor rom (mon) 97 figure 9-1. monitor mode circuit + + + + mc145407 mc74hc125 h(r)c08jl3 rst irq1 osc1 osc2 v ss ptb0 v dd 10 k w 10k w 6 5 2 4 3 1 db-25 2 3 7 20 18 17 19 16 15 v dd v dd 10 m f 10 m f 10 m f 10 m f 1 2 4 7 14 3 0.1 m f 5 6 ptb1 v dd 0.1 m f v dd ptb2 v dd 10 k w ptb3 v dd 10 k w 10 k w 10 k w sw1 a b v dd + v hi notes: 1. sw1: position a ?bus clock = osc1 clock ?4 sw1: position b ?bus clock = osc1 clock ?2 2. see table 18-4 for irq1 voltage level requirements. 3. sw2: position c?external oscillator clock input sw2: position d?crystal oscillator clock input external oscillator must have a 50% duty cycle (see note 1) h(r)c08jk3 h(r)c08jk1 (see note 2) 10m w 20 pf 20 pf 9.8304mhz c d v dd (see note 3) c d x-tal circuit 9.8304 mhz sw2 monitor rom (mon) technical data mc68h(r)c08jl3 ? rev. 4 98 monitor rom (mon) motorola 9.4.1 entering monitor mode table 9-1 shows the pin conditions for entering monitor mode. as specified in the table, monitor mode may be entered after a por and will allow communication at 9600 baud provided one of the following sets of conditions is met: 1. if irq1 = v dd + v hi : osc1 is 4.9125mhz ptb3 = low 2. if irq1 = v dd + v hi : osc1 is 9.8304mhz ptb3 = high if v dd +v hi is applied to irq1 and ptb3 is low upon monitor mode entry ( table 9-1 condition set 1), the bus frequency is a divide-by-two of the clock input to osc1. if ptb3 is high with v dd +v hi applied to irq1 upon monitor mode entry ( table 9-1 condition set 2), the bus frequency is a divide-by-four of the clock input to osc1. holding the ptb3 pin low when entering monitor mode causes a bypass of a divide-by-two stage at the internal clock circuit. in this event, the oscout frequency is table 9-1. monitor mode entry requirements and options irq 1 ptb3 ptb2 ptb1 ptb0 clock source and frequency bus frequency comments v dd + v hi 0011 osc1 at 4.9152mhz 2.4576mhz bypasses rc oscillator (in hrc08xxx); osc1 input must be x-tal oscillator or external oscillator clock. 9600 baud communication on ptb0. cop disabled. v dd + v hi 1011 osc1 at 9.8304mhz 2.4576mhz v dd xxxx x-tal or rc oscillator at desired frequency xtalclk ?4 or rcclk ?4 enters user mode notes: 1. ptb3 = 0: bypasses the divide-by-two prescaler to sim. the osc1 clock must be 50% duty cycle for this condition. 2. xtalclk is the x-tal oscillator output, for mc68hc08xxx. see figure 8-1 . 4. rcclk is the rc oscillator output, for mc68hrc08xxx. see figure 8-2 . 5. see table 18-4 for v dd + v hi voltage level requirements. monitor rom (mon) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola monitor rom (mon) 99 equal to the 2oscout frequency, and osc1 input directly generates internal bus clocks. in this case, the osc1 signal must have a 50% duty cycle at maximum bus frequency. in monitor mode, the cop is disabled as long as v dd + v hi is applied to either the irq1 or the rst pin. (see section 7. system integration module (sim) for more information on modes of operation.) enter monitor mode with the pin configuration shown above by pulling rst low and then high. the rising edge of rst latches monitor mode. once monitor mode is latched, the values on the specified pins can change. once out of reset, the mcu sends a break signal (10 consecutive logic zeros) to the host computer, indicating that it is ready to receive a command. the break signal also provides a timing reference to allow the host to determine the necessary baud rate. in monitor mode, the mcu uses different vectors for reset, swi, and break interrupt. the alternate vectors are in the $fe page instead of the $ff page and allow code execution from the internal monitor firmware instead of user code. table 9-2 is a summary of the vector differences between user mode and monitor mode. when the host computer has completed downloading code into the mcu ram, the host then sends a run command, which executes an rti, which sends control to the address on the stack pointer. table 9-2. monitor mode vector differences modes functions cop reset vector high reset vector low break vector high break vector low swi vector high swi vector low user enabled $fffe $ffff $fffc $fffd $fffc $fffd monitor disabled (1) $fefe $feff $fefc $fefd $fefc $fefd notes: 1. if the high voltage (v dd + v hi ) is removed from the irq 1 pin or the rst pin, the sim asserts its cop enable output. the cop is a mask option enabled or disabled by the copd bit in the configuration register. monitor rom (mon) technical data mc68h(r)c08jl3 ? rev. 4 100 monitor rom (mon) motorola 9.4.2 baud rate the communication baud rate is dependant on oscillator frequency and the state of ptb3 upon monitor mode entry. when ptb3 is high, the divide by ratio is 1024. if the ptb3 pin is at logic zero upon entry into monitor mode, the divide by ratio is 512. 9.4.3 data format communication with the monitor rom is in standard non-return-to-zero (nrz) mark/space data format. (see figure 9-2 and figure 9-3 .) figure 9-2. monitor data format figure 9-3. sample monitor waveforms the data transmit and receive rate can be anywhere from 4800 baud to 28.8k-baud. transmit and receive baud rates must be identical. 9.4.4 echoing as shown in figure 9-4 , the monitor rom immediately echoes each received byte back to the ptb0 pin for error checking. table 9-3. monitor baud rate selection oscillator input frequency ptb3 baud rate 4.9152 mhz 0 9600 bps 9.8304 mhz 1 9600 bps 4.9152 mhz 1 4800 bps bit 5 start bit bit 0 bit 1 next stop bit start bit bit 2 bit 3 bit 4 bit 6 bit 7 bit 5 start bit bit 0 bit 1 next stop bit start bit bit 2 bit 3 bit 4 bit 6 bit 7 start bit bit 0 bit 1 next stop bit start bit bit 2 $a5 break bit 3 bit 4 bit 5 bit 6 bit 7 monitor rom (mon) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola monitor rom (mon) 101 figure 9-4. read transaction any result of a command appears after the echo of the last byte of the command. 9.4.5 break signal a start bit followed by nine low bits is a break signal. (see figure 9-5.) when the monitor receives a break signal, it drives the ptb0 pin high for the duration of two bits before echoing the break signal. figure 9-5. break transaction 9.4.6 commands the monitor rom uses the following commands: read (read memory) write (write memory) iread (indexed read) iwrite (indexed write) readsp (read stack pointer) run (run user program) addr. high read read addr. high addr. low addr. low data echo sent to monitor result 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 missing stop bit two-stop-bit delay before zero echo monitor rom (mon) technical data mc68h(r)c08jl3 ? rev. 4 102 monitor rom (mon) motorola table 9-4. read (read memory) command description read byte from memory operand speci?s 2-byte address in high byte:low byte order data returned returns contents of speci?d address opcode $4a command sequence addr. high read read addr. high addr. low addr. low data echo sent to monitor result table 9-5. write (write memory) command description write byte to memory operand speci?s 2-byte address in high byte:low byte order; low byte followed by data byte data returned none opcode $49 command sequence addr. high write write addr. high addr. low addr. low data echo sent to monitor data monitor rom (mon) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola monitor rom (mon) 103 note: a sequence of iread or iwrite commands can sequentially access a block of memory over the full 64-kbyte memory map. table 9-6. iread (indexed read) command description read next 2 bytes in memory from last address accessed operand speci?s 2-byte address in high byte:low byte order data returned returns contents of next two addresses opcode $1a command sequence data iread iread data echo sent to monitor result table 9-7. iwrite (indexed write) command description write to last address accessed + 1 operand speci?s single data byte data returned none opcode $19 command sequence data iwrite iwrite data echo sent to monitor monitor rom (mon) technical data mc68h(r)c08jl3 ? rev. 4 104 monitor rom (mon) motorola table 9-8. readsp (read stack pointer) command description reads stack pointer operand none data returned returns stack pointer in high byte:low byte order opcode $0c command sequence sp high readsp readsp sp low echo sent to monitor result table 9-9. run (run user program) command description executes rti instruction operand none data returned none opcode $28 command sequence run run echo sent to monitor mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 105 technical data ?mc68h(r)c08jl3 section 10. timer interface module (tim) 10.1 contents 10.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 10.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 10.4 pin name conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 10.5 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 10.5.1 tim counter prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 10.5.2 input capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 10.5.3 output compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 10.5.3.1 unbuffered output compare . . . . . . . . . . . . . . . . . . . . . 110 10.5.3.2 buffered output compare . . . . . . . . . . . . . . . . . . . . . . . 110 10.5.4 pulse width modulation (pwm) . . . . . . . . . . . . . . . . . . . . . 111 10.5.4.1 unbuffered pwm signal generation . . . . . . . . . . . . . . . 112 10.5.4.2 buffered pwm signal generation . . . . . . . . . . . . . . . . . 113 10.5.4.3 pwm initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 10.6 interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 10.7 wait mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 10.8 tim during break interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 116 10.9 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 10.10 i/o registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 10.10.1 tim status and control register (tsc) . . . . . . . . . . . . . . . 117 10.10.2 tim counter registers (tcnth:tcntl) . . . . . . . . . . . . . . 119 10.10.3 tim counter modulo registers (tmodh:tmodl) . . . . . . 120 10.10.4 tim channel status and control registers (tsc0:tsc1) . 121 10.10.5 tim channel registers (tch0h/l:tch1h/l) . . . . . . . . . . 125 timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 106 timer interface module (tim) motorola 10.2 introduction this section describes the timer interface module (tim2, version b). the tim is a two-channel timer that provides a timing reference with input capture, output compare, and pulse-width-modulation functions. figure 10-1 is a block diagram of the tim. 10.3 features features of the tim include the following: two input capture/output compare channels rising-edge, falling-edge, or any-edge input capture trigger set, clear, or toggle output compare action buffered and unbuffered pulse width modulation (pwm) signal generation programmable tim clock input with 7-frequency internal bus clock prescaler selection free-running or modulo up-count operation toggle any channel pin on overflow tim counter stop and reset bits modular architecture expandable to eight channels 10.4 pin name conventions the tim share two i/o pins with two port d i/o pins. the full name of the tim i/o pins are listed in table 10-1 . the generic pin name appear in the text that follows. table 10-1. pin name conventions tim generic pin names: tch0 tch1 full tim pin names: ptd4/tch0 ptd5/tch1 timer interface module (tim) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 107 10.5 functional description figure 10-1 shows the structure of the tim. the central component of the tim is the 16-bit tim counter that can operate as a free-running counter or a modulo up-counter. the tim counter provides the timing reference for the input capture and output compare functions. the tim counter modulo registers, tmodh:tmodl, control the modulo value of the tim counter. software can read the tim counter value at any time without affecting the counting sequence. the two tim channels are programmable independently as input capture or output compare channels. figure 10-1. tim block diagram prescaler prescaler select 16-bit comparator ps2 ps1 ps0 16-bit comparator 16-bit latch tch0h:tch0l ms0a els0b els0a tof toie 16-bit comparator 16-bit latch tch1h:tch1l channel 0 channel 1 tmodh:tmodl trst tstop tov0 ch0ie ch0f els1b els1a tov1 ch1ie ch1max ch1f ch0max ms0b 16-bit counter internal bus ms1a internal bus clock tch1 tch0 interrupt logic port logic interrupt logic interrupt logic port logic timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 108 timer interface module (tim) motorola addr. register name bit 7 654321 bit 0 $0020 tim status and control register (tsc) read: tof toie tstop 00 ps2 ps1 ps0 write: 0 trst reset: 00100000 $0021 tim counter register high (tcnth) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 00000000 $0022 tim counter register low (tcntl) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 00000000 $0023 tim counter modulo register high (tmodh) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 11111111 $0024 tim counter modulo register low (tmodl) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 11111111 $0025 tim channel 0 status and control register (tsc0) read: ch0f ch0ie ms0b ms0a els0b els0a tov0 ch0max write: 0 reset: 00000000 $0026 tim channel 0 register high (tch0h) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: indeterminate after reset $0027 tim channel 0 register low (tch0l) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: indeterminate after reset $0028 tim channel 1 status and control register (tsc1) read: ch1f ch1ie 0 ms1a els1b els1a tov1 ch1max write: 0 reset: 00000000 figure 10-2. tim i/o register summary timer interface module (tim) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 109 10.5.1 tim counter prescaler the tim clock source is one of the seven prescaler outputs. the prescaler generates seven clock rates from the internal bus clock. the prescaler select bits, ps[2:0], in the tim status and control register (tsc) select the tim clock source. 10.5.2 input capture with the input capture function, the tim can capture the time at which an external event occurs. when an active edge occurs on the pin of an input capture channel, the tim latches the contents of the tim counter into the tim channel registers, tchxh:tchxl. the polarity of the active edge is programmable. input captures can generate tim cpu interrupt requests. 10.5.3 output compare with the output compare function, the tim can generate a periodic pulse with a programmable polarity, duration, and frequency. when the counter reaches the value in the registers of an output compare channel, the tim can set, clear, or toggle the channel pin. output compares can generate tim cpu interrupt requests. $0029 tim channel 1 register high (tch1h) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: indeterminate after reset $002a tim channel 1 register low (tch1l) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: indeterminate after reset = unimplemented figure 10-2. tim i/o register summary timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 110 timer interface module (tim) motorola 10.5.3.1 unbuffered output compare any output compare channel can generate unbuffered output compare pulses as described in 10.5.3 output compare . the pulses are unbuffered because changing the output compare value requires writing the new value over the old value currently in the tim channel registers. an unsynchronized write to the tim channel registers to change an output compare value could cause incorrect operation for up to two counter overflow periods. for example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that counter overflow period. also, using a tim overflow interrupt routine to write a new, smaller output compare value may cause the compare to be missed. the tim may pass the new value before it is written. use the following methods to synchronize unbuffered changes in the output compare value on channel x: when changing to a smaller value, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. the output compare interrupt occurs at the end of the current output compare pulse. the interrupt routine has until the end of the counter overflow period to write the new value. when changing to a larger output compare value, enable channel x tim overflow interrupts and write the new value in the tim overflow interrupt routine. the tim overflow interrupt occurs at the end of the current counter overflow period. writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same counter overflow period. 10.5.3.2 buffered output compare channels 0 and 1 can be linked to form a buffered output compare channel whose output appears on the tch0 pin. the tim channel registers of the linked pair alternately control the output. setting the ms0b bit in tim channel 0 status and control register (tsc0) links channel 0 and channel 1. the output compare value in the tim timer interface module (tim) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 111 channel 0 registers initially controls the output on the tch0 pin. writing to the tim channel 1 registers enables the tim channel 1 registers to synchronously control the output after the tim overflows. at each subsequent overflow, the tim channel registers (0 or 1) that control the output are the ones written to last. tsc0 controls and monitors the buffered output compare function, and tim channel 1 status and control register (tsc1) is unused. while the ms0b bit is set, the channel 1 pin, tch1, is available as a general-purpose i/o pin. note: in buffered output compare operation, do not write new output compare values to the currently active channel registers. writing to the active channel registers is the same as generating unbuffered output compares. 10.5.4 pulse width modulation (pwm) by using the toggle-on-overflow feature with an output compare channel, the tim can generate a pwm signal. the value in the tim counter modulo registers determines the period of the pwm signal. the channel pin toggles when the counter reaches the value in the tim counter modulo registers. the time between overflows is the period of the pwm signal. as figure 10-3 shows, the output compare value in the tim channel registers determines the pulse width of the pwm signal. the time between overflow and output compare is the pulse width. program the tim to clear the channel pin on output compare if the state of the pwm pulse is logic one. program the tim to set the pin if the state of the pwm pulse is logic zero. timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 112 timer interface module (tim) motorola figure 10-3. pwm period and pulse width the value in the tim counter modulo registers and the selected prescaler output determines the frequency of the pwm output. the frequency of an 8-bit pwm signal is variable in 256 increments. writing $00ff (255) to the tim counter modulo registers produces a pwm period of 256 times the internal bus clock period if the prescaler select value is 000 (see 10.10.1 tim status and control register (tsc) ). the value in the tim channel registers determines the pulse width of the pwm output. the pulse width of an 8-bit pwm signal is variable in 256 increments. writing $0080 (128) to the tim channel registers produces a duty cycle of 128/256 or 50%. 10.5.4.1 unbuffered pwm signal generation any output compare channel can generate unbuffered pwm pulses as described in 10.5.4 pulse width modulation (pwm) . the pulses are unbuffered because changing the pulse width requires writing the new pulse width value over the old value currently in the tim channel registers. an unsynchronized write to the tim channel registers to change a pulse width value could cause incorrect operation for up to two pwm periods. for example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that pwm period. also, using a tim overflow interrupt routine to tchx period pulse width overflow overflow overflow output compare output compare output compare timer interface module (tim) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 113 write a new, smaller pulse width value may cause the compare to be missed. the tim may pass the new value before it is written. use the following methods to synchronize unbuffered changes in the pwm pulse width on channel x: when changing to a shorter pulse width, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. the output compare interrupt occurs at the end of the current pulse. the interrupt routine has until the end of the pwm period to write the new value. when changing to a longer pulse width, enable channel x tim overflow interrupts and write the new value in the tim overflow interrupt routine. the tim overflow interrupt occurs at the end of the current pwm period. writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same pwm period. note: in pwm signal generation, do not program the pwm channel to toggle on output compare. toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self- correct in the event of software error or noise. toggling on output compare also can cause incorrect pwm signal generation when changing the pwm pulse width to a new, much larger value. 10.5.4.2 buffered pwm signal generation channels 0 and 1 can be linked to form a buffered pwm channel whose output appears on the tch0 pin. the tim channel registers of the linked pair alternately control the pulse width of the output. setting the ms0b bit in tim channel 0 status and control register (tsc0) links channel 0 and channel 1. the tim channel 0 registers initially control the pulse width on the tch0 pin. writing to the tim channel 1 registers enables the tim channel 1 registers to synchronously control the pulse width at the beginning of the next pwm period. at each subsequent overflow, the tim channel registers (0 or 1) that control the pulse width are the ones written to last. tsc0 controls and monitors the buffered pwm function, and tim channel 1 status and control register timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 114 timer interface module (tim) motorola (tsc1) is unused. while the ms0b bit is set, the channel 1 pin, tch1, is available as a general-purpose i/o pin. note: in buffered pwm signal generation, do not write new pulse width values to the currently active channel registers. writing to the active channel registers is the same as generating unbuffered pwm signals. 10.5.4.3 pwm initialization to ensure correct operation when generating unbuffered or buffered pwm signals, use the following initialization procedure: 1. in the tim status and control register (tsc): a. stop the tim counter by setting the tim stop bit, tstop. b. reset the tim counter by setting the tim reset bit, trst. 2. in the tim counter modulo registers (tmodh:tmodl), write the value for the required pwm period. 3. in the tim channel x registers (tchxh:tchxl), write the value for the required pulse width. 4. in tim channel x status and control register (tscx): a. write 0:1 (for unbuffered output compare or pwm signals) or 1:0 (for buffered output compare or pwm signals) to the mode select bits, msxb:msxa. (see table 10-3 .) b. write 1 to the toggle-on-overflow bit, tovx. c. write 1:0 (to clear output on compare) or 1:1 (to set output on compare) to the edge/level select bits, elsxb:elsxa. the output action on compare must force the output to the complement of the pulse width level. (see table 10-3 .) note: in pwm signal generation, do not program the pwm channel to toggle on output compare. toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self- correct in the event of software error or noise. toggling on output compare can also cause incorrect pwm signal generation when changing the pwm pulse width to a new, much larger value. 5. in the tim status control register (tsc), clear the tim stop bit, tstop. timer interface module (tim) interrupts mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 115 setting ms0b links channels 0 and 1 and configures them for buffered pwm operation. the tim channel 0 registers (tch0h:tch0l) initially control the buffered pwm output. tim status control register 0 (tscr0) controls and monitors the pwm signal from the linked channels. ms0b takes priority over ms0a. clearing the toggle-on-overflow bit, tovx, inhibits output toggles on tim overflows. subsequent output compares try to force the output to a state it is already in and have no effect. the result is a 0% duty cycle output. setting the channel x maximum duty cycle bit (chxmax) and clearing the tovx bit generates a 100% duty cycle output. (see 10.10.4 tim channel status and control registers (tsc0:tsc1) .) 10.6 interrupts the following tim sources can generate interrupt requests: tim overflow flag (tof) ?the tof bit is set when the tim counter value rolls over to $0000 after matching the value in the tim counter modulo registers. the tim overflow interrupt enable bit, toie, enables tim overflow cpu interrupt requests. tof and toie are in the tim status and control register. tim channel flags (ch1f:ch0f) ?the chxf bit is set when an input capture or output compare occurs on channel x. channel x tim cpu interrupt requests are controlled by the channel x interrupt enable bit, chxie. channel x tim cpu interrupt requests are enabled when chxie=1. chxf and chxie are in the tim channel x status and control register. 10.7 wait mode the wait instruction puts the mcu in low-power-consumption standby mode. the tim remains active after the execution of a wait instruction. in wait mode the tim registers are not accessible by the cpu. any enabled cpu interrupt request from the tim can bring the mcu out of wait mode. timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 116 timer interface module (tim) motorola if tim functions are not required during wait mode, reduce power consumption by stopping the tim before executing the wait instruction. 10.8 tim during break interrupts a break interrupt stops the tim counter. the system integration module (sim) controls whether status bits in other modules can be cleared during the break state. the bcfe bit in the break flag control register (bfcr) enables software to clear status bits during the break state. (see 7.8.3 break flag control register (bfcr) .) to allow software to clear status bits during a break interrupt, write a logic one to the bcfe bit. if a status bit is cleared during the break state, it remains cleared when the mcu exits the break state. to protect status bits during the break state, write a logic zero to the bcfe bit. with bcfe at logic zero (its default state), software can read and write i/o registers during the break state without affecting status bits. some status bits have a two-step read/write clearing procedure. if software does the first step on such a bit before the break, the bit cannot change during the break state as long as bcfe is at logic zero. after the break, doing the second step clears the status bit. 10.9 i/o signals port d shares two of its pins with the tim. the two tim channel i/o pins are ptd4/tch0 and ptd5/tch1. each channel i/o pin is programmable independently as an input capture pin or an output compare pin. ptd4/tch0 can be configured as a buffered output compare or buffered pwm pin. timer interface module (tim) i/o registers mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 117 10.10 i/o registers the following i/o registers control and monitor operation of the tim: tim status and control register (tsc) tim control registers (tcnth:tcntl) tim counter modulo registers (tmodh:tmodl) tim channel status and control registers (tsc0 and tsc1) tim channel registers (tch0h:tch0l and tch1h:tch1l) 10.10.1 tim status and control register (tsc) the tim status and control register does the following: enables tim overflow interrupts flags tim overflows stops the tim counter resets the tim counter prescales the tim counter clock tof ?tim overflow flag bit this read/write flag is set when the tim counter resets to $0000 after reaching the modulo value programmed in the tim counter modulo registers. clear tof by reading the tim status and control register when tof is set and then writing a logic zero to tof. if another tim address: $0020 bit 7 654321 bit 0 read: tof toie tstop 00 ps2 ps1 ps0 write: 0 trst reset: 00100000 = unimplemented figure 10-4. tim status and control register (tsc) timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 118 timer interface module (tim) motorola overflow occurs before the clearing sequence is complete, then writing logic zero to tof has no effect. therefore, a tof interrupt request cannot be lost due to inadvertent clearing of tof. reset clears the tof bit. writing a logic one to tof has no effect. 1 = tim counter has reached modulo value 0 = tim counter has not reached modulo value toie ?tim overflow interrupt enable bit this read/write bit enables tim overflow interrupts when the tof bit becomes set. reset clears the toie bit. 1 = tim overflow interrupts enabled 0 = tim overflow interrupts disabled tstop ?tim stop bit this read/write bit stops the tim counter. counting resumes when tstop is cleared. reset sets the tstop bit, stopping the tim counter until software clears the tstop bit. 1 = tim counter stopped 0 = tim counter active note: do not set the tstop bit before entering wait mode if the tim is required to exit wait mode. trst ?tim reset bit setting this write-only bit resets the tim counter and the tim prescaler. setting trst has no effect on any other registers. counting resumes from $0000. trst is cleared automatically after the tim counter is reset and always reads as logic zero. reset clears the trst bit. 1 = prescaler and tim counter cleared 0 = no effect note: setting the tstop and trst bits simultaneously stops the tim counter at a value of $0000. ps[2:0] ?prescaler select bits these read/write bits select one of the seven prescaler outputs as the input to the tim counter as table 10-2 shows. reset clears the ps[2:0] bits. timer interface module (tim) i/o registers mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 119 10.10.2 tim counter registers (tcnth:tcntl) the two read-only tim counter registers contain the high and low bytes of the value in the tim counter. reading the high byte (tcnth) latches the contents of the low byte (tcntl) into a buffer. subsequent reads of tcnth do not affect the latched tcntl value until tcntl is read. reset clears the tim counter registers. setting the tim reset bit (trst) also clears the tim counter registers. note: if you read tcnth during a break interrupt, be sure to unlatch tcntl by reading tcntl before exiting the break interrupt. otherwise, tcntl retains the value latched during the break. table 10-2. prescaler selection ps2 ps1 ps0 tim clock source 0 0 0 internal bus clock ?1 0 0 1 internal bus clock ?2 0 1 0 internal bus clock ?4 0 1 1 internal bus clock ?8 1 0 0 internal bus clock ?16 1 0 1 internal bus clock ?32 1 1 0 internal bus clock ?64 1 1 1 not available timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 120 timer interface module (tim) motorola 10.10.3 tim counter modulo registers (tmodh:tmodl) the read/write tim modulo registers contain the modulo value for the tim counter. when the tim counter reaches the modulo value, the overflow flag (tof) becomes set, and the tim counter resumes counting from $0000 at the next clock. writing to the high byte (tmodh) inhibits the tof bit and overflow interrupts until the low byte (tmodl) is written. reset sets the tim counter modulo registers. address: $0021 tcnth bit 7 654321 bit 0 read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 00000000 address: $0022 tcntl bit 7 654321 bit 0 read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 00000000 = unimplemented figure 10-5. tim counter registers (tcnth:tcntl) timer interface module (tim) i/o registers mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 121 note: reset the tim counter before writing to the tim counter modulo registers. 10.10.4 tim channel status and control registers (tsc0:tsc1) each of the tim channel status and control registers does the following: flags input captures and output compares enables input capture and output compare interrupts selects input capture, output compare, or pwm operation selects high, low, or toggling output on output compare selects rising edge, falling edge, or any edge as the active input capture trigger selects output toggling on tim overflow selects 100% pwm duty cycle selects buffered or unbuffered output compare/pwm operation address: $0023 tmodh bit 7 654321 bit 0 read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 11111111 address: $0024 tmodl bit 7 654321 bit 0 read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 11111111 figure 10-6. tim counter modulo registers (tmodh:tmodl) timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 122 timer interface module (tim) motorola chxf ?channel x flag bit when channel x is an input capture channel, this read/write bit is set when an active edge occurs on the channel x pin. when channel x is an output compare channel, chxf is set when the value in the tim counter registers matches the value in the tim channel x registers. when tim cpu interrupt requests are enabled (chxie=1), clear chxf by reading the tim channel x status and control register with chxf set and then writing a logic zero to chxf. if another interrupt request occurs before the clearing sequence is complete, then writing logic zero to chxf has no effect. therefore, an interrupt request cannot be lost due to inadvertent clearing of chxf. reset clears the chxf bit. writing a logic one to chxf has no effect. 1 = input capture or output compare on channel x 0 = no input capture or output compare on channel x chxie ?channel x interrupt enable bit this read/write bit enables tim cpu interrupt service requests on channel x. reset clears the chxie bit. 1 = channel x cpu interrupt requests enabled 0 = channel x cpu interrupt requests disabled address: $0025 tsc0 bit 7 654321 bit 0 read: ch0f ch0ie ms0b ms0a els0b els0a tov0 ch0max write: 0 reset: 00000000 address: $0028 tsc1 bit 7 654321 bit 0 read: ch1f ch1ie 0 ms1a els1b els1a tov1 ch1max write: 0 reset: 00000000 = unimplemented figure 10-7. tim channel status and control registers (tsc0:tsc1) timer interface module (tim) i/o registers mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 123 msxb ?mode select bit b this read/write bit selects buffered output compare/pwm operation. msxb exists only in the tim channel 0 status and control register. setting ms0b disables the channel 1 status and control register and reverts tch1 to general-purpose i/o. reset clears the msxb bit. 1 = buffered output compare/pwm operation enabled 0 = buffered output compare/pwm operation disabled msxa ?mode select bit a when elsxb:a 1 00, this read/write bit selects either input capture operation or unbuffered output compare/pwm operation. see table 10-3 . 1 = unbuffered output compare/pwm operation 0 = input capture operation when elsxb:a = 00, this read/write bit selects the initial output level of the tchx pin. (see table 10-3 .) reset clears the msxa bit. 1 = initial output level low 0 = initial output level high note: before changing a channel function by writing to the msxb or msxa bit, set the tstop and trst bits in the tim status and control register (tsc). elsxb and elsxa ?edge/level select bits when channel x is an input capture channel, these read/write bits control the active edge-sensing logic on channel x. when channel x is an output compare channel, elsxb and elsxa control the channel x output behavior when an output compare occurs. when elsxb and elsxa are both clear, channel x is not connected to an i/o port, and pin tchx is available as a general-purpose i/o pin. table 10-3 shows how elsxb and elsxa work. reset clears the elsxb and elsxa bits. timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 124 timer interface module (tim) motorola note: before enabling a tim channel register for input capture operation, make sure that the tchx pin is stable for at least two bus clocks. tovx ?toggle-on-overflow bit when channel x is an output compare channel, this read/write bit controls the behavior of the channel x output when the tim counter overflows. when channel x is an input capture channel, tovx has no effect. reset clears the tovx bit. 1 = channel x pin toggles on tim counter overflow. 0 = channel x pin does not toggle on tim counter overflow. note: when tovx is set, a tim counter overflow takes precedence over a channel x output compare if both occur at the same time. chxmax ?channel x maximum duty cycle bit when the tovx bit is at logic zero, setting the chxmax bit forces the duty cycle of buffered and unbuffered pwm signals to 100%. as figure 10-8 shows, the chxmax bit takes effect in the cycle after it is set or cleared. the output stays at the 100% duty cycle level until the cycle after chxmax is cleared. table 10-3. mode, edge, and level selection msxb msxa elsxb elsxa mode configuration x0 0 0 output preset pin under port control; initial output level high x1 0 0 pin under port control; initial output level low 00 0 1 input capture capture on rising edge only 0 0 1 0 capture on falling edge only 0 0 1 1 capture on rising or falling edge 01 0 1 output compare or pwm toggle output on compare 0 1 1 0 clear output on compare 0 1 1 1 set output on compare 1 x 0 1 buffered output compare or buffered pwm toggle output on compare 1 x 1 0 clear output on compare 1 x 1 1 set output on compare timer interface module (tim) i/o registers mc68h(r)c08jl3 ? rev. 4 technical data motorola timer interface module (tim) 125 figure 10-8. chxmax latency 10.10.5 tim channel registers (tch0h/l:tch1h/l) these read/write registers contain the captured tim counter value of the input capture function or the output compare value of the output compare function. the state of the tim channel registers after reset is unknown. in input capture mode (msxb:msxa = 0:0), reading the high byte of the tim channel x registers (tchxh) inhibits input captures until the low byte (tchxl) is read. in output compare mode (msxb:msxa 1 0:0), writing to the high byte of the tim channel x registers (tchxh) inhibits output compares until the low byte (tchxl) is written. output overflow tchx period chxmax overflow overflow overflow overflow compare output compare output compare output compare timer interface module (tim) technical data mc68h(r)c08jl3 ? rev. 4 126 timer interface module (tim) motorola address: $0026 tch0h bit 7 654321 bit 0 read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: indeterminate after reset address: $0027 tch0l bit 7 654321 bit 0 read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: indeterminate after reset address: $0029 tch1h bit 7 654321 bit 0 read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: indeterminate after reset address: $02a tch1l bit 7 654321 bit 0 read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: indeterminate after reset figure 10-9. tim channel registers (tch0h/l:tch1h/l) mc68h(r)c08jl3 ? rev. 4 technical data motorola analog-to-digital converter (adc) 127 technical data ?mc68h(r)c08jl3 section 11. analog-to-digital converter (adc) 11.1 contents 11.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 11.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 11.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 11.4.1 adc port i/o pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 11.4.2 voltage conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 11.4.3 conversion time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 11.4.4 continuous conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 11.4.5 accuracy and precision . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.5 interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.7 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.7.1 adc voltage in (adcvin) . . . . . . . . . . . . . . . . . . . . . . . . . 132 11.8 i/o registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 11.8.1 adc status and control register. . . . . . . . . . . . . . . . . . . . 132 11.8.2 adc data register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 11.8.3 adc input clock register . . . . . . . . . . . . . . . . . . . . . . . . . 135 11.2 introduction this section describes the analog-to-digital converter (adc). the adc is an 8-bit, 12-channels analog-to-digital converter. analog-to-digital converter (adc) technical data mc68h(r)c08jl3 ? rev. 4 128 analog-to-digital converter (adc) motorola 11.3 features features of the adc module include: 12 channels with multiplexed input linear successive approximation with monotonicity 8-bit resolution single or continuous conversion conversion complete flag or conversion complete interrupt selectable adc clock 11.4 functional description twelve adc channels are available for sampling external sources at pins ptb0?tb7 and ptd0?td3. an analog multiplexer allows the single adc converter to select one of the 12 adc channels as adc voltage input (adcvin). adcvin is converted by the successive approximation register-based counters. the adc resolution is 8 bits. when the conversion is completed, adc puts the result in the adc data register and sets a flag or generates an interrupt. figure 11-2 shows a block diagram of the adc. addr. register name bit 7 654321 bit 0 $003c adc status and control register (adscr) read: coco aien adco ch4 ch3 ch2 ch1 ch0 write: reset: 00011111 $003d adc data register (adr) read: ad7 ad6 ad5 ad4 ad3 ad2 ad1 ad0 write: reset: indeterminate after reset $003e adc input clock register (adiclk) read: adiv2 adiv1 adiv0 00000 write: reset: 00000000 figure 11-1. adc i/o register summary analog-to-digital converter (adc) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola analog-to-digital converter (adc) 129 figure 11-2. adc block diagram 11.4.1 adc port i/o pins ptb0?tb7 and ptd0?td3 are general-purpose i/o pins that are shared with the adc channels. the channel select bits (adc status and control register, $003c), define which adc channel/port pin will be used as the input signal. the adc overrides the port i/o logic by forcing that pin as input to the adc. the remaining adc channels/port pins are controlled by the port i/o logic and can be used as general-purpose i/o. internal data b u s interrupt logic channel select adc clock generator conversion complete adc voltage in adcvin adc clock bus clock ch[4:0] adc data register adiv[2:0] adiclk aien coco disable disable adc channel x read ddrb/ddrd write ddrb/ddrd reset write ptb/ptd read ptb/ptd ddrbx/ddrdx ptbx/ptdx (1 of 12 channels) adcx analog-to-digital converter (adc) technical data mc68h(r)c08jl3 ? rev. 4 130 analog-to-digital converter (adc) motorola writes to the port register or ddr will not have any affect on the port pin that is selected by the adc. read of a port pin which is in use by the adc will return a logic 0 if the corresponding ddr bit is at logic 0. if the ddr bit is at logic 1, the value in the port data latch is read. 11.4.2 voltage conversion when the input voltage to the adc equals v dd , the adc converts the signal to $ff (full scale). if the input voltage equals v ss, the adc converts it to $00. input voltages between v dd and v ss are a straight-line linear conversion. all other input voltages will result in $ff if greater than v dd and $00 if less than v ss . note: input voltage should not exceed the analog supply voltages. 11.4.3 conversion time sixteen adc internal clocks are required to perform one conversion. the adc starts a conversion on the first rising edge of the adc internal clock immediately following a write to the adscr. if the adc internal clock is selected to run at 1mhz, then one conversion will take 16 m s to complete. with a 1mhz adc internal clock the maximum sample rate is 62.5khz. 11.4.4 continuous conversion in the continuous conversion mode, the adc continuously converts the selected channel filling the adc data register with new data after each conversion. data from the previous conversion will be overwritten whether that data has been read or not. conversions will continue until the adco bit is cleared. the coco bit (adc status & control register, $003c) is set after each conversion and can be cleared by writing the adc status and control register or reading of the adc data register. 16 adc clock cycles conversion time = adc clock frequency number of bus cycles = conversion time bus frequency analog-to-digital converter (adc) interrupts mc68h(r)c08jl3 ? rev. 4 technical data motorola analog-to-digital converter (adc) 131 11.4.5 accuracy and precision the conversion process is monotonic and has no missing codes. 11.5 interrupts when the aien bit is set, the adc module is capable of generating a cpu interrupt after each adc conversion. a cpu interrupt is generated if the coco bit is at logic 0. the coco bit is not used as a conversion complete flag when interrupts are enabled. 11.6 low-power modes the following subsections describe the adc in low-power modes. 11.6.1 wait mode the adc continues normal operation during wait mode. any enabled cpu interrupt request from the adc can bring the mcu out of wait mode. if the adc is not required to bring the mcu out of wait mode, power down the adc by setting the ch[4:0] bits in the adc status and control register to logic 1? before executing the wait instruction. 11.6.2 stop mode the adc module is inactive after the execution of a stop instruction. any pending conversion is aborted. adc conversions resume when the mcu exits stop mode. allow one conversion cycle to stabilize the analog circuitry before attempting a new adc conversion after exiting stop mode. 11.7 i/o signals the adc module has 12 channels that are shared with i/o port b and port d. analog-to-digital converter (adc) technical data mc68h(r)c08jl3 ? rev. 4 132 analog-to-digital converter (adc) motorola 11.7.1 adc voltage in (adcvin) adcvin is the input voltage signal from one of the 12 adc channels to the adc module. 11.8 i/o registers these i/o registers control and monitor adc operation: adc status and control register (adscr) adc data register (adr) adc clock register (adiclk) 11.8.1 adc status and control register the following paragraphs describe the function of the adc status and control register. coco ?conversions complete bit when the aien bit is a logic 0, the coco is a read-only bit which is set each time a conversion is completed. this bit is cleared whenever the adc status and control register is written or whenever the adc data register is read. reset clears this bit. 1 = conversion completed (aien = 0) 0 = conversion not completed (aien = 0) when the aien bit is a logic 1 (cpu interrupt enabled), the coco is a read-only bit, and will always be logic 0 when read. address: $003c bit 7 654321 bit 0 read: coco aien adco ch4 ch3 ch2 ch1 ch0 write: reset: 00011111 = unimplemented figure 11-3. adc status and control register (adscr) analog-to-digital converter (adc) i/o registers mc68h(r)c08jl3 ? rev. 4 technical data motorola analog-to-digital converter (adc) 133 aien ?adc interrupt enable bit when this bit is set, an interrupt is generated at the end of an adc conversion. the interrupt signal is cleared when the data register is read or the status/control register is written. reset clears the aien bit. 1 = adc interrupt enabled 0 = adc interrupt disabled adco ?adc continuous conversion bit when set, the adc will convert samples continuously and update the adr register at the end of each conversion. only one conversion is allowed when this bit is cleared. reset clears the adco bit. 1 = continuous adc conversion 0 = one adc conversion adch[4:0] ?adc channel select bits adch4, adch3, adch2, adch1, and adch0 form a 5-bit field which is used to select one of the adc channels. the five channel select bits are detailed in the following table. care should be taken when using a port pin as both an analog and a digital input simultaneously to prevent switching noise from corrupting the analog signal. (see table 11-1.) the adc subsystem is turned off when the channel select bits are all set to one. this feature allows for reduced power consumption for the mcu when the adc is not used. reset sets all of these bits to a logic 1. note: recovery from the disabled state requires one conversion cycle to stabilize. analog-to-digital converter (adc) technical data mc68h(r)c08jl3 ? rev. 4 134 analog-to-digital converter (adc) motorola 11.8.2 adc data register one 8-bit result register is provided. this register is updated each time an adc conversion completes. table 11-1. mux channel select ch4 ch3 ch2 ch1 ch0 adc channel input select 00000 adc0 ptb0 00001 adc1 ptb1 00010 adc2 ptb2 00011 adc3 ptb3 00100 adc4 ptb4 00101 adc5 ptb5 00110 adc6 ptb6 00111 adc7 ptb7 01000 adc8 ptd3 01001 adc9 ptd2 01010 adc10 ptd1 01011 adc11 ptd0 01100 unused (see note 1) ::::: 11010 11011 reserved 11 1 0 0 unused 11 1 0 1 v dda (see note 2) 11 1 1 0 v ssa (see note 2) 11 1 1 1 adc power off notes: 1. if any unused channels are selected, the resulting adc conversion will be unknown. 2. the voltage levels supplied from internal reference nodes as specified in the table are used to verify the operation of the adc converter both in production test and for user applications. analog-to-digital converter (adc) i/o registers mc68h(r)c08jl3 ? rev. 4 technical data motorola analog-to-digital converter (adc) 135 11.8.3 adc input clock register this register selects the clock frequency for the adc. adiv2:adiv0 ?adc clock prescaler bits adiv2, adiv1, and adiv0 form a 3-bit field which selects the divide ratio used by the adc to generate the internal adc clock. table 11-2 shows the available clock configurations. the adc clock should be set to approximately 1mhz. address: $003d bit 7 654321 bit 0 read: ad7 ad6 ad5 ad4 ad3 ad2 ad1 ad0 write: reset: indeterminate after reset = unimplemented figure 11-4. adc data register (adr) address: $003e bit 7 654321 bit 0 read: adiv2 adiv1 adiv0 00000 write: reset: 0 0000000 = unimplemented figure 11-5. adc input clock register (adiclk) analog-to-digital converter (adc) technical data mc68h(r)c08jl3 ? rev. 4 136 analog-to-digital converter (adc) motorola table 11-2. adc clock divide ratio adiv2 adiv1 adiv0 adc clock rate 0 0 0 adc input clock ?1 0 0 1 adc input clock ?2 0 1 0 adc input clock ?4 0 1 1 adc input clock ?8 1 x x adc input clock ?16 x = don? care mc68h(r)c08jl3 ? rev. 4 technical data motorola i/o ports 137 technical data ?mc68h(r)c08jl3 section 12. i/o ports 12.1 contents 12.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 12.3 port a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 12.3.1 port a data register (pta) . . . . . . . . . . . . . . . . . . . . . . . . 139 12.3.2 data direction register a (ddra) . . . . . . . . . . . . . . . . . . . 140 12.3.3 port a input pull-up enable register (ptapue) . . . . . . . . 141 12.4 port b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.4.1 port b data register (ptb) . . . . . . . . . . . . . . . . . . . . . . . . 143 12.4.2 data direction register b (ddrb) . . . . . . . . . . . . . . . . . . . 143 12.5 port d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12.5.1 port d data register (ptd) . . . . . . . . . . . . . . . . . . . . . . . . 145 12.5.2 data direction register d (ddrd). . . . . . . . . . . . . . . . . . . 146 12.5.3 port d control register (pdcr). . . . . . . . . . . . . . . . . . . . . 147 12.2 introduction twenty three bidirectional input-output (i/o) pins form three parallel ports. all i/o pins are programmable as inputs or outputs. note: connect any unused i/o pins to an appropriate logic level, either v dd or v ss . although the i/o ports do not require termination for proper operation, termination reduces excess current consumption and the possibility of electrostatic damage. i/o ports technical data mc68h(r)c08jl3 ? rev. 4 138 i/o ports motorola 12.3 port a port a is an 7-bit special function port that shares all seven of its pins with the keyboard interrupt (kbi) module, see section 14. each port a pin also has software configurable pull-up device if the corresponding port pin is configured as input port. pta0 to pta5 has direct led drive capability. addr. register name bit 7 654321 bit 0 $0000 port a data register (pta) read: 0 pta6 pta5 pta4 pta3 pta2 pta1 pta0 write: reset: unaffected by reset $0001 port b data register (ptb) read: ptb7 ptb6 ptb5 ptb4 ptb3 ptb2 ptb1 ptb0 write: reset: unaffected by reset $0003 port d data register (ptd) read: ptd7 ptd6 ptd5 ptd4 ptd3 ptd2 ptd1 ptd0 write: reset: unaffected by reset $0004 data direction register a (ddra) read: 0 ddra6 ddra5 ddra4 ddra3 ddra2 ddra1 ddra0 write: reset: 00000000 $0005 data direction register b (ddrb) read: ddrb7 ddrb6 ddrb5 ddrb4 ddrb3 ddrb2 ddrb1 ddrb0 write: reset: 00000000 $0007 data direction register d (ddrd) read: ddrd7 ddrd6 ddrd5 ddrd4 ddrd3 ddrd2 ddrd1 ddrd0 write: reset: 00000000 $000a port d control register (pdcr) read: 0000 slowd7 slowd6 ptdpu7 ptdpu6 write: reset: 00000000 $000d port a input pull-up enable register (ptapue) read: pta6en ptapue6 ptapue5 ptapue4 ptapue3 ptapue2 ptapue1 ptapue0 write: reset: 00000000 figure 12-1. i/o port register summary i/o ports port a mc68h(r)c08jl3 ? rev. 4 technical data motorola i/o ports 139 12.3.1 port a data register (pta) the port a data register (pta) contains a data latch for each of the seven port a pins. pta[6:0] ?port a data bits these read/write bits are software programmable. data direction of each port a pin is under the control of the corresponding bit in data direction register a. reset has no effect on port a data. kbi[6:0] ?port a keyboard interrupts the keyboard interrupt enable bits, kbie6-kbie0, in the keyboard interrupt control register (kbaier) enable the port a pins as external interrupt pins, (see section 14. keyboard interrupt module (kbi) ). address: $0000 bit 7 654321 bit 0 read: 0 pta6 pta5 pta4 pta3 pta2 pta1 pta0 write: reset: unaffected by reset additional functions: led (sink) led (sink) led (sink) led (sink) led (sink) led (sink) 30k pull-up 30k pull-up 30k pull-up 30k pull-up 30k pull-up 30k pull-up 30k pull-up keyboard interrupt keyboard interrupt keyboard interrupt keyboard interrupt keyboard interrupt keyboard interrupt keyboard interrupt figure 12-2. port a data register (pta) i/o ports technical data mc68h(r)c08jl3 ? rev. 4 140 i/o ports motorola 12.3.2 data direction register a (ddra) data direction register a determines whether each port a pin is an input or an output. writing a logic one to a ddra bit enables the output buffer for the corresponding port a pin; a logic zero disables the output buffer. ddra[6:0] ?data direction register a bits these read/write bits control port a data direction. reset clears ddra[6:0], configuring all port a pins as inputs. 1 = corresponding port a pin configured as output 0 = corresponding port a pin configured as input note: avoid glitches on port a pins by writing to the port a data register before changing data direction register a bits from 0 to 1. figure 12-4 shows the port a i/o logic. address: $0004 bit 7 654321 bit 0 read: 0 ddra6 ddra5 ddra4 ddra3 ddra2 ddra1 ddra0 write: reset: 0 0000000 figure 12-3. data direction register a (ddra) i/o ports port a mc68h(r)c08jl3 ? rev. 4 technical data motorola i/o ports 141 figure 12-4. port a i/o circuit when ddrax is a logic 1, reading address $0000 reads the ptax data latch. when ddrax is a logic 0, reading address $0000 reads the voltage level on the pin. the data latch can always be written, regardless of the state of its data direction bit. 12.3.3 port a input pull-up enable register (ptapue) the port a input pull-up enable register (ptapue) contains a software configurable pull-up device for each if the seven port a pins. each bit is individually configurable and requires the corresponding data direction register, ddrax be configured as input. each pull-up device is automatically and dynamically disabled when its corresponding ddrax bit is configured as output. read ddra ($0004) write ddra ($0004) reset write pta ($0000) read pta ($0000) ptax ddrax ptax internal data bus 30k ptapuex to keyboard interrupt circuit i/o ports technical data mc68h(r)c08jl3 ? rev. 4 142 i/o ports motorola pta6en ?enable pta6 on osc2 this read/write bit configures the osc2 pin function when rc oscillator option is selected. this bit has no effect for x-tal oscillator option. 1 = osc2 pin configured for pta6 i/o, and has all the interrupt and pull-up functions. 0 = osc2 pin outputs the rc oscillator clock (rcclk) ptapue[6:0] ?port a input pull-up enable bits these read/write bits are software programmable to enable pull-up devices on port a pins 1 = corresponding port a pin configured to have internal pull if its ddra bit is set to 0 0 = pull-up device is disconnected on the corresponding port a pin regardless of the state of its ddra bit. table 12-1 summarizes the operation of the port b pins. address: $000d bit 7 6 5 4 3 2 1 bit 0 read: pta6en ptapue6 ptapue5 ptapue4 ptapue3 ptapue2 ptapue2 ptapue0 write: reset: 00000000 figure 12-5. port a input pull-up enable register (ptapue) table 12-1. port a pin functions ptapue bit ddra bit pta bit i/o pin mode accesses to ddrb accesses to ptb read/write read write 10x (1) input, v dd (2) ddra6-ddra0 pin pta6-pta0 (3) 0 0 x input, hi-z (4) ddra6-ddra0 pin pta6-pta0 (3) x 1 x output ddra6-ddra0 pta6-pta0 pta6-pta0 1. x = don? care. 2. i/o pin pulled to v dd by internal pull-up. 3. writing affects data register, but does not affect input. 4. hi-z = high impedence i/o ports port b mc68h(r)c08jl3 ? rev. 4 technical data motorola i/o ports 143 12.4 port b port b is an 8-bit special function port that shares all eight of its port pins with the analog-to-digital converter (adc) module, see section 11. 12.4.1 port b data register (ptb) the port b data register contains a data latch for each of the eight port b pins. ptb[7:0] ?port b data bits these read/write bits are software programmable. data direction of each port b pin is under the control of the corresponding bit in data direction register b. reset has no effect on port b data. 12.4.2 data direction register b (ddrb) data direction register b determines whether each port b pin is an input or an output. writing a logic one to a ddrb bit enables the output buffer for the corresponding port b pin; a logic zero disables the output buffer. address: $0001 bit 7 654321 bit 0 read: ptb7 ptb6 ptb5 ptb4 ptb3 ptb2 ptb1 ptb0 write: reset: unaffected by reset alternative function: adc7 adc6 adc5 adc4 adc3 adc2 adc2 adc0 figure 12-6. port b data register (ptb) address: $0005 bit 7 654321 bit 0 read: ddrb7 ddrb6 ddrb5 ddrb4 ddrb3 ddrb2 ddrb1 ddrb0 write: reset: 0 0000000 figure 12-7. data direction register b (ddrb) i/o ports technical data mc68h(r)c08jl3 ? rev. 4 144 i/o ports motorola ddrb[7:0] ?data direction register b bits these read/write bits control port b data direction. reset clears ddrb[7:0], configuring all port b pins as inputs. 1 = corresponding port b pin configured as output 0 = corresponding port b pin configured as input note: avoid glitches on port b pins by writing to the port b data register before changing data direction register b bits from 0 to 1. figure 12-8 shows the port b i/o logic. figure 12-8. port b i/o circuit when ddrbx is a logic 1, reading address $0001 reads the ptbx data latch. when ddrbx is a logic 0, reading address $0001 reads the voltage level on the pin. the data latch can always be written, regardless of the state of its data direction bit. table 12-2 summarizes the operation of the port b pins. table 12-2. port b pin functions ddrb bit ptb bit i/o pin mode accesses to ddrb accesses to ptb read/write read write 0x (1) 1. x = don? care input, hi-z (2) 2. hi-z = high impedance ddrb7-ddrb0 pin ptb[7:0] (3) 3. writing affects data register, but does not affect the input. 1 x output ddrb7-ddrb0 pin ptb[7:0] read ddrb ($0005) write ddrb ($0005) reset write ptb ($0001) read ptb ($0001) ptbx ddrbx ptbx internal data bus to analog-to-digital converter i/o ports port d mc68h(r)c08jl3 ? rev. 4 technical data motorola i/o ports 145 12.5 port d port d is an 8-bit special function port that shares two of its pins with timer interface module, (see section 10. ) and shares four of its pins with analog to digital conversion module (see section 11. ). ptd6 and ptd7 each has high current drive (25ma sink) and programmable pull- up. ptd2, ptd3, ptd6 and ptd7 each has led driving capability. 12.5.1 port d data register (ptd) the port d data register contains a data latch for each of the eight port d pins. ptd[7:0] ?port d data bits these read/write bits are software programmable. data direction of each port d pin is under the control of the corresponding bit in data direction register d. reset has no effect on port d data. address: $0003 bit 7 654321 bit 0 read: ptd7 ptd6 ptd5 ptd4 ptd3 ptd2 ptd1 ptd0 write: reset: additional functions led led led led adc8 adc9 adc10 adc11 tch1 tch0 25ma sink (slow edge) 25ma sink (slow edge) 5k pull-up 5k pull-up figure 12-9. port d data register (ptd) i/o ports technical data mc68h(r)c08jl3 ? rev. 4 146 i/o ports motorola 12.5.2 data direction register d (ddrd) data direction register d determines whether each port d pin is an input or an output. writing a logic one to a ddrd bit enables the output buffer for the corresponding port d pin; a logic zero disables the output buffer. ddrd[7:0] ?data direction register d bits these read/write bits control port d data direction. reset clears ddrd[7:0], configuring all port d pins as inputs. 1 = corresponding port d pin configured as output 0 = corresponding port d pin configured as input note: avoid glitches on port d pins by writing to the port d data register before changing data direction register d bits from 0 to 1. figure 12-11 shows the port d i/o logic. figure 12-11. port d i/o circuit address: $0007 bit 7 654321 bit 0 read: ddrd7 ddrd6 ddrd5 ddrd4 ddrd3 ddrd2 ddrd1 ddrd0 write: reset: 0 0000000 figure 12-10. data direction register d (ddrd) read ddrd ($0007) write ddrd ($0007) reset write ptd ($0003) read ptd ($0003) ptdx ddrdx ptdx internal data bus ptd[0:3] to analog-to-digital converter 5k ptdpu[6:7] ptd[4:5] to timer i/o ports port d mc68h(r)c08jl3 ? rev. 4 technical data motorola i/o ports 147 when ddrdx is a logic 1, reading address $0003 reads the ptdx data latch. when ddrdx is a logic 0, reading address $0003 reads the voltage level on the pin. the data latch can always be written, regardless of the state of its data direction bit. table 12-3 summarizes the operation of the port d pins. 12.5.3 port d control register (pdcr) the port d control register enables/disables the pull-up resistor and slow-edge high current capability of pins ptd6 and ptd7. slowdx ?slow edge enable the slowd6 and slowd7 bits enable the slow-edge, open-drain, high current output (25ma sink) of port pins ptd6 and ptd7 respectively. ddrx bit is not affected by slowdx. 1 = slow edge enabled; pin is open-drain output 0 = slow edge disabled; pin is push-pull ptdpux ?pull-up enable the ptdpu6 and ptdpu7 bits enable the 5k pull-up on ptd6 and ptd7 respectively, regardless the status of ddrdx bit. 1 = enable 5k pull-up 0 = disable 5k pull-up table 12-3. port d pin functions ddrd bit ptd bit i/o pin mode accesses to ddra accesses to ptd read/write read write 0x (1) 1. x = don? care input, hi-z (2) 2. hi-z = high impedance ddrd[7:0] pin ptd[7:0] (3) 3. writing affects data register, but does not affect the input. 1 x output ddrd[7:0] pin ptd[7:0] address: $000a bit 7 654321 bit 0 read: 0000 slowd7 slowd6 ptdpu7 ptdpu6 write: reset: 0 0000000 figure 12-12. port d control register (pdcr) i/o ports technical data mc68h(r)c08jl3 ? rev. 4 148 i/o ports motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola external interrupt (irq) 149 technical data ?mc68h(r)c08jl3 section 13. external interrupt (irq) 13.1 contents 13.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 13.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 13.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 13.4.1 irq1 pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 13.5 irq module during break interrupts . . . . . . . . . . . . . . . . . . . 153 13.6 irq status and control register (iscr) . . . . . . . . . . . . . . . . 153 13.2 introduction the irq (external interrupt) module provides a maskable interrupt input. 13.3 features features of the irq module include the following: a dedicated external interrupt pin, i rq1 irq1 interrupt control bits hysteresis buffer programmable edge-only or edge and level interrupt sensitivity automatic interrupt acknowledge selectable internal pullup resistor external interrupt (irq) technical data mc68h(r)c08jl3 ? rev. 4 150 external interrupt (irq) motorola 13.4 functional description a logic zero applied to the external interrupt pin can latch a cpu interrupt request. figure 13-1 shows the structure of the irq module. interrupt signals on the irq1 pin are latched into the irq1 latch. an interrupt latch remains set until one of the following actions occurs: vector fetch ?a vector fetch automatically generates an interrupt acknowledge signal that clears the irq latch. software clear ?software can clear the interrupt latch by writing to the acknowledge bit in the interrupt status and control register (iscr). writing a logic one to the ack1 bit clears the irq1 latch. reset ?a reset automatically clears the interrupt latch. the external interrupt pin is falling-edge-triggered and is software- configurable to be either falling-edge or falling-edge and low-level- triggered. the mode1 bit in the iscr controls the triggering sensitivity of the irq1 pin. when the interrupt pin is edge-triggered only, the cpu interrupt request remains set until a vector fetch, software clear, or reset occurs. when the interrupt pin is both falling-edge and low-level-triggered, the cpu interrupt request remains set until both of the following occur: vector fetch or software clear return of the interrupt pin to logic one the vector fetch or software clear may occur before or after the interrupt pin returns to logic one. as long as the pin is low, the interrupt request remains pending. a reset will clear the latch and the mode1 control bit, thereby clearing the interrupt even if the pin stays low. when set, the imask1 bit in the iscr mask all external interrupt requests. a latched interrupt request is not presented to the interrupt priority logic unless the imask1 bit is clear. external interrupt (irq) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola external interrupt (irq) 151 note: the interrupt mask (i) in the condition code register (ccr) masks all interrupt requests, including external interrupt requests. (see 7.6 exception control .) figure 13-1. irq module block diagram 13.4.1 irq1 pin a logic zero on the irq1 pin can latch an interrupt request into the irq1 latch. a vector fetch, software clear, or reset clears the irq1 latch. if the mode1 bit is set, the irq1 pin is both falling-edge-sensitive and low-level-sensitive. with mode1 set, both of the following actions must occur to clear irq1: ack1 imask1 dq ck clr irq1 high interrupt to mode select logic irq1 ff request v dd mode1 voltage detect synchro- nizer irqf1 to cpu for bil/bih instructions vector fetch decoder internal address bus reset v dd i nternal pullup device irq1 irqpud addr. register name bit 7 654321 bit 0 $001d irq status and control register (intscr) read: 0000 irqf1 0 imask1 mode1 write: ack1 reset: 00000000 = unimplemented figure 13-2. irq i/o register summary external interrupt (irq) technical data mc68h(r)c08jl3 ? rev. 4 152 external interrupt (irq) motorola vector fetch or software clear ?a vector fetch generates an interrupt acknowledge signal to clear the latch. software may generate the interrupt acknowledge signal by writing a logic one to the ack1 bit in the interrupt status and control register (iscr). the ack1 bit is useful in applications that poll the irq1 pin and require software to clear the irq1 latch. writing to the ack1 bit prior to leaving an interrupt service routine can also prevent spurious interrupts due to noise. setting ack1 does not affect subsequent transitions on the irq1 pin. a falling edge that occurs after writing to the ack1 bit latches another interrupt request. if the irq1 mask bit, imask1, is clear, the cpu loads the program counter with the vector address at locations $fffa and $fffb. return of the irq1 pin to logic one ?as long as the irq1 pin is at logic zero, irq1 remains active. the vector fetch or software clear and the return of the irq1 pin to logic one may occur in any order. the interrupt request remains pending as long as the irq1 pin is at logic zero. a reset will clear the latch and the mode1 control bit, thereby clearing the interrupt even if the pin stays low. if the mode1 bit is clear, the irq1 pin is falling-edge-sensitive only. with mode1 clear, a vector fetch or software clear immediately clears the irq1 latch. the irqf1 bit in the iscr register can be used to check for pending interrupts. the irqf1 bit is not affected by the imask1 bit, which makes it useful in applications where polling is preferred. use the bih or bil instruction to read the logic level on the irq1 pin. note: when using the level-sensitive interrupt trigger, avoid false interrupts by masking interrupt requests in the interrupt routine. note: an internal pull-up resistor to v dd is connected to the irq1 pin; this can be disabled by setting the irqpud bit in the config2 register ($001e). external interrupt (irq) irq module during break interrupts mc68h(r)c08jl3 ? rev. 4 technical data motorola external interrupt (irq) 153 13.5 irq module during break interrupts the system integration module (sim) controls whether the irq1 latch can be cleared during the break state. the bcfe bit in the break flag control register (bfcr) enables software to clear the latches during the break state. (see section 7. system integration module (sim) .) to allow software to clear the irq1 latch during a break interrupt, write a logic one to the bcfe bit. if a latch is cleared during the break state, it remains cleared when the mcu exits the break state. to protect the latches during the break state, write a logic zero to the bcfe bit. with bcfe at logic zero (its default state), writing to the ack1 bit in the irq status and control register during the break state has no effect on the irq latch. 13.6 irq status and control register (iscr) the irq status and control register (iscr) controls and monitors operation of the irq module. the iscr has the following functions: shows the state of the irq1 flag clears the irq1 latch masks irq1 and interrupt request controls triggering sensitivity of the irq1 interrupt pin address: $001d bit 7 654321 bit 0 read: 0000 irqf1 imask1 mode1 write: ack1 reset: 00000000 = unimplemented figure 13-3. irq status and control register (intscr) external interrupt (irq) technical data mc68h(r)c08jl3 ? rev. 4 154 external interrupt (irq) motorola irqf1 ?irq1 flag this read-only status bit is high when the irq1 interrupt is pending. 1 = irq1 interrupt pending 0 = irq1 interrupt not pending ack1 ?irq1 interrupt request acknowledge bit writing a logic one to this write-only bit clears the irq1 latch. ack1 always reads as logic zero. reset clears ack1. imask1 ?irq1 interrupt mask bit writing a logic one to this read/write bit disables irq1 interrupt requests. reset clears imask1. 1 = irq1 interrupt requests disabled 0 = irq1 interrupt requests enabled mode1 ?irq1 edge/level select bit this read/write bit controls the triggering sensitivity of the irq1 pin. reset clears mode1. 1 = irq1 interrupt requests on falling edges and low levels 0 = irq1 interrupt requests on falling edges only irqpud ?irq1 pin pull-up control bit 1 = internal pull-up is disconnected 0 = internal pull-up is connected between irq1 pin and v dd address: $001e bit 7 654321 bit 0 read: irqpud r r lvit1 lvit0 r r r write: reset: 0 0 0 not affected not affected 000 por: 00000000 r = reserved figure 13-4. configuration register 2 (config2) mc68h(r)c08jl3 ? rev. 4 technical data motorola keyboard interrupt module (kbi) 155 technical data ?mc68h(r)c08jl3 section 14. keyboard interrupt module (kbi) 14.1 contents 14.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 14.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 14.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 14.4.1 keyboard initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 14.4.2 keyboard status and control register. . . . . . . . . . . . . . . . 159 14.4.3 keyboard interrupt enable register . . . . . . . . . . . . . . . . . . 160 14.5 wait mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 14.6 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 14.7 keyboard module during break interrupts . . . . . . . . . . . . . . . 161 14.2 introduction the keyboard interrupt module (kbi) provides seven independently maskable external interrupts which are accessible via pta0?ta6 pins. 14.3 features features of the keyboard interrupt module include the following: seven keyboard interrupt pins with separate keyboard interrupt enable bits and one keyboard interrupt mask software configurable pull-up device if input pin is configured as input port bit programmable edge-only or edge- and level- interrupt sensitivity exit from low-power modes keyboard interrupt module (kbi) technical data mc68h(r)c08jl3 ? rev. 4 156 keyboard interrupt module (kbi) motorola 14.4 functional description figure 14-2. keyboard interrupt block diagram writing to the kbie6?bie0 bits in the keyboard interrupt enable register independently enables or disables each port a pin as a keyboard interrupt pin. enabling a keyboard interrupt pin in port a also enables its internal pull-up device irrespective of ptapuex bits in the port a input pull-up enable register (see 12.3.3 ). a logic 0 applied to an enabled keyboard interrupt pin latches a keyboard interrupt request. addr. register name bit 7 654321 bit 0 $001a keyboard status and control register (kbscr) read: 0000 keyf 0 imaskk modek write: ackk reset: 00000000 $001b keyboard interrupt enable register (kbier) read: 0 kbie6 kbie5 kbie4 kbie3 kbie2 kbie1 kbie0 write: reset: 00000000 = unimplemented figure 14-1. kbi i/o register summary kbie0 kbie6 . . . dq ck clr v dd modek imaskk keyboard interrupt ff vector fetch decoder ackk internal bus reset kbi6 kbi0 synchronizer keyf keyboard interrupt request to pullup enable to pullup enable keyboard interrupt module (kbi) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola keyboard interrupt module (kbi) 157 a keyboard interrupt is latched when one or more keyboard pins goes low after all were high. the modek bit in the keyboard status and control register controls the triggering mode of the keyboard interrupt. if the keyboard interrupt is edge-sensitive only, a falling edge on a keyboard pin does not latch an interrupt request if another keyboard pin is already low. to prevent losing an interrupt request on one pin because another pin is still low, software can disable the latter pin while it is low. if the keyboard interrupt is falling edge- and low level-sensitive, an interrupt request is present as long as any keyboard pin is low. if the modek bit is set, the keyboard interrupt pins are both falling edge- and low level-sensitive, and both of the following actions must occur to clear a keyboard interrupt request: vector fetch or software clear ?a vector fetch generates an interrupt acknowledge signal to clear the interrupt request. software may generate the interrupt acknowledge signal by writing a logic 1 to the ackk bit in the keyboard status and control register kbscr. the ackk bit is useful in applications that poll the keyboard interrupt pins and require software to clear the keyboard interrupt request. writing to the ackk bit prior to leaving an interrupt service routine can also prevent spurious interrupts due to noise. setting ackk does not affect subsequent transitions on the keyboard interrupt pins. a falling edge that occurs after writing to the ackk bit latches another interrupt request. if the keyboard interrupt mask bit, imaskk, is clear, the cpu loads the program counter with the vector address at locations $ffe0 and $ffe1. return of all enabled keyboard interrupt pins to logic 1 ?as long as any enabled keyboard interrupt pin is at logic 0, the keyboard interrupt remains set. the vector fetch or software clear and the return of all enabled keyboard interrupt pins to logic 1 may occur in any order. keyboard interrupt module (kbi) technical data mc68h(r)c08jl3 ? rev. 4 158 keyboard interrupt module (kbi) motorola if the modek bit is clear, the keyboard interrupt pin is falling-edge- sensitive only. with modek clear, a vector fetch or software clear immediately clears the keyboard interrupt request. reset clears the keyboard interrupt request and the modek bit, clearing the interrupt request even if a keyboard interrupt pin stays at logic 0. the keyboard flag bit (keyf) in the keyboard status and control register can be used to see if a pending interrupt exists. the keyf bit is not affected by the keyboard interrupt mask bit (imaskk) which makes it useful in applications where polling is preferred. to determine the logic level on a keyboard interrupt pin, disable the pull- up device, use the data direction register to configure the pin as an input and then read the data register. note: setting a keyboard interrupt enable bit (kbiex) forces the corresponding keyboard interrupt pin to be an input, overriding the data direction register. however, the data direction register bit must be a logic 0 for software to read the pin. 14.4.1 keyboard initialization when a keyboard interrupt pin is enabled, it takes time for the internal pull-up to reach a logic 1. therefore a false interrupt can occur as soon as the pin is enabled. to prevent a false interrupt on keyboard initialization: 1. mask keyboard interrupts by setting the imaskk bit in the keyboard status and control register. 2. enable the kbi pins by setting the appropriate kbiex bits in the keyboard interrupt enable register. 3. write to the ackk bit in the keyboard status and control register to clear any false interrupts. 4. clear the imaskk bit. an interrupt signal on an edge-triggered pin can be acknowledged immediately after enabling the pin. an interrupt signal on an edge- and keyboard interrupt module (kbi) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola keyboard interrupt module (kbi) 159 level-triggered interrupt pin must be acknowledged after a delay that depends on the external load. another way to avoid a false interrupt: 1. configure the keyboard pins as outputs by setting the appropriate ddra bits in the data direction register a. 2. write logic 1s to the appropriate port a data register bits. 3. enable the kbi pins by setting the appropriate kbiex bits in the keyboard interrupt enable register. 14.4.2 keyboard status and control register flags keyboard interrupt requests. acknowledges keyboard interrupt requests. masks keyboard interrupt requests. controls keyboard interrupt triggering sensitivity. bits 7? ?not used these read-only bits always read as logic 0s. keyf ?keyboard flag bit this read-only bit is set when a keyboard interrupt is pending on port- a. reset clears the keyf bit. 1 = keyboard interrupt pending 0 = no keyboard interrupt pending address: $001a bit 7 654321 bit 0 read: 0000 keyf 0 imaskk modek write: ackk reset: 00000000 = unimplemented figure 14-3. keyboard status and control register (kbscr) keyboard interrupt module (kbi) technical data mc68h(r)c08jl3 ? rev. 4 160 keyboard interrupt module (kbi) motorola ackk ?keyboard acknowledge bit writing a logic 1 to this write-only bit clears the keyboard interrupt request on port-a. ackk always reads as logic 0. reset clears ackk. imaskk?keyboard interrupt mask bit writing a logic 1 to this read/write bit prevents the output of the keyboard interrupt mask from generating interrupt requests on port-a. reset clears the imaskk bit. 1 = keyboard interrupt requests masked 0 = keyboard interrupt requests not masked modek ?keyboard triggering sensitivity bit this read/write bit controls the triggering sensitivity of the keyboard interrupt pins on port-a. reset clears modek. 1 = keyboard interrupt requests on falling edges and low levels 0 = keyboard interrupt requests on falling edges only 14.4.3 keyboard interrupt enable register the port-a keyboard interrupt enable register enables or disables each port-a pin to operate as a keyboard interrupt pin. kbie6?bie0 ?port-a keyboard interrupt enable bits each of these read/write bits enables the corresponding keyboard interrupt pin on port-a to latch interrupt requests. reset clears the keyboard interrupt enable register. 1 = kbix pin enabled as keyboard interrupt pin 0 = kbix pin not enabled as keyboard interrupt pin address: $001b bit 7 654321 bit 0 read: 0 kbie6 kbie5 kbie4 kbie3 kbie2 kbie1 kbie0 write: reset: 00000000 figure 14-4. keyboard interrupt enable register (kbier) keyboard interrupt module (kbi) wait mode mc68h(r)c08jl3 ? rev. 4 technical data motorola keyboard interrupt module (kbi) 161 14.5 wait mode the keyboard modules remain active in wait mode. clearing the imaskk bit in the keyboard status and control register enables keyboard interrupt requests to bring the mcu out of wait mode. 14.6 stop mode the keyboard module remains active in stop mode. clearing the imaskk bit in the keyboard status and control register enables keyboard interrupt requests to bring the mcu out of stop mode. 14.7 keyboard module during break interrupts the system integration module (sim) controls whether the keyboard interrupt latch can be cleared during the break state. the bcfe bit in the break flag control register (bfcr) enables software to clear status bits during the break state. to allow software to clear the keyboard interrupt latch during a break interrupt, write a logic 1 to the bcfe bit. if a latch is cleared during the break state, it remains cleared when the mcu exits the break state. to protect the latch during the break state, write a logic 0 to the bcfe bit. with bcfe at logic 0 (its default state), writing to the keyboard acknowledge bit (ackk) in the keyboard status and control register during the break state has no effect. keyboard interrupt module (kbi) technical data mc68h(r)c08jl3 ? rev. 4 162 keyboard interrupt module (kbi) motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola computer operating properly (cop) 163 technical data ?mc68h(r)c08jl3 section 15. computer operating properly (cop) 15.1 contents 15.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 15.3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 15.4 i/o signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.1 2oscout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.2 copctl write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.3 power-on reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.4 internal reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 15.4.5 reset vector fetch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 15.4.6 copd (cop disable). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 15.4.7 coprs (cop rate select) . . . . . . . . . . . . . . . . . . . . . . . . 166 15.5 cop control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.6 interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.7 monitor mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.8 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.8.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 15.8.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 15.9 cop module during break mode . . . . . . . . . . . . . . . . . . . . . . 168 15.2 introduction the computer operating properly (cop) module contains a free-running counter that generates a reset if allowed to overflow. the cop module helps software recover from runaway code. prevent a cop reset by clearing the cop counter periodically. the cop module can be disabled through the copd bit in the config1 register. computer operating properly (cop) technical data mc68h(r)c08jl3 ? rev. 4 164 computer operating properly (cop) motorola 15.3 functional description figure 15-1 shows the structure of the cop module. figure 15-1. cop block diagram the cop counter is a free-running 6-bit counter preceded by the 12-bit system integration module (sim) counter. if not cleared by software, the cop counter overflows and generates an asynchronous reset after 2 18 ?2 4 or 2 13 ?2 4 2oscout cycles; depending on the state of the cop rate select bit, coprs, in configuration register 1. with a 2 18 ?2 4 2oscout cycle overflow option, a 8mhz crystal gives a cop timeout period of 32.766 ms. writing any value to location $ffff before an overflow occurs prevents a cop reset by clearing the cop counter and stages 12 through 5 of the sim counter. copctl write 2oscout reset vector fetch sim reset circuit reset status register internal reset sources (1) sim clear stages 5?2 12-bit sim counter clear all stages copd (from config1) reset copctl write clear cop module copen (from sim) cop counter note: 1. see sim section for more details. cop clock cop timeout cop rate sel (coprs from config1) 6-bit cop counter computer operating properly (cop) i/o signals mc68h(r)c08jl3 ? rev. 4 technical data motorola computer operating properly (cop) 165 note: service the cop immediately after reset and before entering or after exiting stop mode to guarantee the maximum time before the first cop counter overflow. a cop reset pulls the rst pin low for 32 2oscout cycles and sets the cop bit in the reset status register (rsr). (see 7.8.2 reset status register (rsr) .). note: place cop clearing instructions in the main program and not in an interrupt subroutine. such an interrupt subroutine could keep the cop from generating a reset even while the main program is not working properly. 15.4 i/o signals the following paragraphs describe the signals shown in figure 15-1 . 15.4.1 2oscout 2oscout is the oscillator output signal. 2oscout frequency is equal to the crystal frequency or the rc-oscillator frequency. 15.4.2 copctl write writing any value to the cop control register (copctl) (see 15.5 cop control register ) clears the cop counter and clears bits 12 through 5 of the sim counter. reading the cop control register returns the low byte of the reset vector. 15.4.3 power-on reset the power-on reset (por) circuit in the sim clears the sim counter 4096 2oscout cycles after power-up. 15.4.4 internal reset an internal reset clears the sim counter and the cop counter. computer operating properly (cop) technical data mc68h(r)c08jl3 ? rev. 4 166 computer operating properly (cop) motorola 15.4.5 reset vector fetch a reset vector fetch occurs when the vector address appears on the data bus. a reset vector fetch clears the sim counter. 15.4.6 copd (cop disable) the copd signal reflects the state of the cop disable bit (copd) in the configuration register (config). (see section 5. configuration register (config) .) 15.4.7 coprs (cop rate select) the coprs signal reflects the state of the cop rate select bit (coprs) in the configuration register 1. coprs ?cop rate select bit coprs selects the cop timeout period. reset clears coprs. 1 = cop timeout period is (2 13 ?2 4 ) 2oscout cycles 0 = cop timeout period is (2 18 ?2 4 ) 2oscout cycles copd ?cop disable bit copd disables the cop module. 1 = cop module disabled 0 = cop module enabled address: $001f bit 7 654321 bit 0 read: coprs r r lvid r ssrec stop copd write: reset: 00000000 r = reserved figure 15-2. configuration register 1 (config1) computer operating properly (cop) cop control register mc68h(r)c08jl3 ? rev. 4 technical data motorola computer operating properly (cop) 167 15.5 cop control register the cop control register is located at address $ffff and overlaps the reset vector. writing any value to $ffff clears the cop counter and starts a new timeout period. reading location $ffff returns the low byte of the reset vector. 15.6 interrupts the cop does not generate cpu interrupt requests. 15.7 monitor mode the cop is disabled in monitor mode when v dd + v hi is present on the irq1 pin or on the rst pin. 15.8 low-power modes the wait and stop instructions put the mcu in low-power consumption standby modes. 15.8.1 wait mode the cop continues to operate during wait mode. to prevent a cop reset during wait mode, periodically clear the cop counter in a cpu interrupt routine. address: $ffff bit 7 654321 bit 0 read: low byte of reset vector write: clear cop counter reset: unaffected by reset figure 15-3. cop control register (copctl) computer operating properly (cop) technical data mc68h(r)c08jl3 ? rev. 4 168 computer operating properly (cop) motorola 15.8.2 stop mode stop mode turns off the 2oscout input to the cop and clears the sim counter. service the cop immediately before entering or after exiting stop mode to ensure a full cop timeout period after entering or exiting stop mode. 15.9 cop module during break mode the cop is disabled during a break interrupt when v dd + v hi is present on the rst pin. mc68h(r)c08jl3 ? rev. 4 technical data motorola low voltage inhibit (lvi) 169 technical data ?mc68h(r)c08jl3 section 16. low voltage inhibit (lvi) 16.1 contents 16.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 16.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 16.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 16.5 lvi control register (config2/config1) . . . . . . . . . . . . . . 170 16.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 16.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 16.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 16.2 introduction this section describes the low-voltage inhibit module (lvi), which monitors the voltage on the v dd pin and generates a reset when the v dd voltage falls to the lvi trip (lvi trip ) voltage. 16.3 features features of the lvi module include the following: selectable lvi trip voltage selectable lvi circuit disable low voltage inhibit (lvi) technical data mc68h(r)c08jl3 ? rev. 4 170 low voltage inhibit (lvi) motorola 16.4 functional description figure 16-1 shows the structure of the lvi module. the lvi is enabled after a reset. the lvi module contains a bandgap reference circuit and comparator. setting lvi disable bit (lvid) disables the lvi to monitor v dd voltage. the lvi trip voltage selection bits (lvit1, lvit0) determines at which v dd level the lvi module should take actions. the lvi module generates one output signal: lvi reset ?an reset signal will be generated to reset the cpu when v dd drops to below the set trip point. figure 16-1. lvi module block diagram 16.5 lvi control register (config2/config1) low v dd lvt1 lvid detector v dd lvi reset lvt0 v dd > lvi trip = 0 v dd < lvi trip = 1 address: $001e bit 7 654321 bit 0 read: irqpud r r lvit1 lvit0 r r r write: reset: 0 0 0 not affected not affected 000 por: 00000000 r = reserved figure 16-2. configuration register 2 (config2) low voltage inhibit (lvi) low-power modes mc68h(r)c08jl3 ? rev. 4 technical data motorola low voltage inhibit (lvi) 171 lvid low voltage inhibit disable bit 1 = low voltage inhibit disabled 0 = low voltage inhibit enabled lvit1, lvit0 ?lvi trip voltage selection these two bits determine at which level of v dd the lvi module will come into action. lvit1 and lvit0 are cleared by a power-on reset only. 16.6 low-power modes the stop and wait instructions put the mcu in low-power- consumption standby modes. 16.6.1 wait mode the lvi module, when enabled, will continue to operate in wait mode. 16.6.2 stop mode the lvi module, when enabled, will continue to operate in stop mode. address: $001f bit 7 654321 bit 0 read: coprs r r lvid r ssrec stop copd write: reset: 00000000 r = reserved figure 16-3. configuration register 1 (config1) lvit1 lvit0 trip voltage (1) 1. see section 18. electrical specifications for full parameters. comments 00v lvr3 (2.4v) for v dd =3v operation 01v lvr3 (2.4v) for v dd =3v operation 10v lvr5 (4.0v) for v dd =5v operation 1 1 reserved low voltage inhibit (lvi) technical data mc68h(r)c08jl3 ? rev. 4 172 low voltage inhibit (lvi) motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola break module (break) 173 technical data ?mc68h(r)c08jl3 section 17. break module (break) 17.1 contents 17.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 17.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 17.4 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 17.4.1 flag protection during break interrupts . . . . . . . . . . . . . . . 176 17.4.2 cpu during break interrupts . . . . . . . . . . . . . . . . . . . . . . . 176 17.4.3 tim during break interrupts . . . . . . . . . . . . . . . . . . . . . . . . 176 17.4.4 cop during break interrupts . . . . . . . . . . . . . . . . . . . . . . . 176 17.5 break module registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 17.5.1 break status and control register (brkscr) . . . . . . . . . 177 17.5.2 break address registers . . . . . . . . . . . . . . . . . . . . . . . . . . 178 17.5.3 break status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 17.5.4 break flag control register (bfcr) . . . . . . . . . . . . . . . . . 180 17.6 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 17.6.1 wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 17.6.2 stop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 17.2 introduction this section describes the break module. the break module can generate a break interrupt that stops normal program flow at a defined address to enter a background program. break module (break) technical data mc68h(r)c08jl3 ? rev. 4 174 break module (break) motorola 17.3 features features of the break module include the following: accessible i/o registers during the break interrupt cpu-generated break interrupts software-generated break interrupts cop disabling during break interrupts 17.4 functional description when the internal address bus matches the value written in the break address registers, the break module issues a breakpoint signal (bkpt ) to the sim. the sim then causes the cpu to load the instruction register with a software interrupt instruction (swi) after completion of the current cpu instruction. the program counter vectors to $fffc and $fffd ($fefc and $fefd in monitor mode). the following events can cause a break interrupt to occur: a cpu-generated address (the address in the program counter) matches the contents of the break address registers. software writes a logic one to the brka bit in the break status and control register. when a cpu generated address matches the contents of the break address registers, the break interrupt begins after the cpu completes its current instruction. a return from interrupt instruction (rti) in the break routine ends the break interrupt and returns the mcu to normal operation. figure 17-1 shows the structure of the break module. break module (break) functional description mc68h(r)c08jl3 ? rev. 4 technical data motorola break module (break) 175 figure 17-1. break module block diagram iab[15:8] iab[7:0] 8-bit comparator 8-bit comparator control break address register low break address register high iab[15:0] bkpt (to sim) addr. register name bit 7 654321 bit 0 $fe00 break status register (bsr) read: rrrrrr sbsw r write: see note reset: 0 $fe03 break flag control register (bfcr) read: bcfe rrrrrrr write: reset: 0 $fe0c break address high register (brkh) read: bit15 bit14 bit13 bit12 bit11 bit10 bit9 bit8 write: reset: 00000000 $fe0d break address low register (brkl) read: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 write: reset: 00000000 $fe0e break status and control register (brkscr) read: brke brka 000000 write: reset: 00000000 note: writing a logic 0 clears sbsw. = unimplemented r = reserved figure 17-2. break i/o register summary break module (break) technical data mc68h(r)c08jl3 ? rev. 4 176 break module (break) motorola 17.4.1 flag protection during break interrupts the system integration module (sim) controls whether or not module status bits can be cleared during the break state. the bcfe bit in the break flag control register (bfcr) enables software to clear status bits during the break state. (see 7.8.3 break flag control register (bfcr) and see the break interrupts subsection for each module.) 17.4.2 cpu during break interrupts the cpu starts a break interrupt by: loading the instruction register with the swi instruction loading the program counter with $fffc:$fffd ($fefc:$fefd in monitor mode) the break interrupt begins after completion of the cpu instruction in progress. if the break address register match occurs on the last cycle of a cpu instruction, the break interrupt begins immediately. 17.4.3 tim during break interrupts a break interrupt stops the timer counter. 17.4.4 cop during break interrupts the cop is disabled during a break interrupt when v dd + v hi is present on the rst pin. 17.5 break module registers these registers control and monitor operation of the break module: break status and control register (brkscr) break address register high (brkh) break address register low (brkl) break status register (bsr) break flag control register (bfcr) break module (break) break module registers mc68h(r)c08jl3 ? rev. 4 technical data motorola break module (break) 177 17.5.1 break status and control register (brkscr) the break status and control register contains break module enable and status bits. brke ?break enable bit this read/write bit enables breaks on break address register matches. clear brke by writing a logic zero to bit 7. reset clears the brke bit. 1 = breaks enabled on 16-bit address match 0 = breaks disabled brka ?break active bit this read/write status and control bit is set when a break address match occurs. writing a logic one to brka generates a break interrupt. clear brka by writing a logic zero to it before exiting the break routine. reset clears the brka bit. 1 = break address match 0 = no break address match address: $fe0e bit 7 654321 bit 0 read: brke brka 000000 write: reset: 00000000 = unimplemented figure 17-3. break status and control register (brkscr) break module (break) technical data mc68h(r)c08jl3 ? rev. 4 178 break module (break) motorola 17.5.2 break address registers the break address registers contain the high and low bytes of the desired breakpoint address. reset clears the break address registers. 17.5.3 break status register the break status register contains a flag to indicate that a break caused an exit from stop or wait mode. address: $fe0c bit 7 654321 bit 0 read: bit 15 14 13 12 11 10 9 bit 8 write: reset: 00000000 figure 17-4. break address register high (brkh) address: $fe0d bit 7 654321 bit 0 read: bit 7 654321 bit 0 write: reset: 00000000 figure 17-5. break address register low (brkl) address: $fe00 bit 7 654321 bit 0 read: rrrrrr sbsw r write: note (1) reset: 0 r = reserved 1. writing a logic zero clears sbsw. figure 17-6. break status register (bsr) break module (break) break module registers mc68h(r)c08jl3 ? rev. 4 technical data motorola break module (break) 179 sbsw ?sim break stop/wait this status bit is useful in applications requiring a return to wait or stop mode after exiting from a break interrupt. clear sbsw by writing a logic zero to it. reset clears sbsw. 1 = stop mode or wait mode was exited by break interrupt 0 = stop mode or wait mode was not exited by break interrupt sbsw can be read within the break state swi routine. the user can modify the return address on the stack by subtracting one from it. the following code is an example of this. writing zero to the sbsw bit clears it. ; ; ; this code works if the h register has been pushed onto the stack in the break service routine software. this code should be executed at the end of the break service routine software. hibyte equ 5 lobyte equ 6 ; if not sbsw, do rti brclr sbsw,bsr, return ; ; see if wait mode or stop mode was exited by break. tst lobyte,sp ; if returnlo is not zero, bne dolo ; then just decrement low byte. dec hibyte,sp ; else deal with high byte, too. dolo dec lobyte,sp ; point to wait/stop opcode. return pulh rti ; restore h register. break module (break) technical data mc68h(r)c08jl3 ? rev. 4 180 break module (break) motorola 17.5.4 break flag control register (bfcr) the break control register contains a bit that enables software to clear status bits while the mcu is in a break state. bcfe ?break clear flag enable bit this read/write bit enables software to clear status bits by accessing status registers while the mcu is in a break state. to clear status bits during the break state, the bcfe bit must be set. 1 = status bits clearable during break 0 = status bits not clearable during break 17.6 low-power modes the wait and stop instructions put the mcu in low-power- consumption standby modes. 17.6.1 wait mode if enabled, the break module is active in wait mode. in the break routine, the user can subtract one from the return address on the stack if sbsw is set (see 7.7 low-power modes ). clear the sbsw bit by writing logic zero to it. 17.6.2 stop mode a break interrupt causes exit from stop mode and sets the sbsw bit in the break status register. see 7.8 sim registers . address: $fe03 bit 7 654321 bit 0 read: bcfe rrrrrrr write: reset: 0 r = reserved figure 17-7. break flag control register (bfcr) mc68h(r)c08jl3 ? rev. 4 technical data motorola electrical specifications 181 technical data ?mc68h(r)c08jl3 section 18. electrical specifications 18.1 contents 18.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 18.3 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 182 18.4 functional operating range. . . . . . . . . . . . . . . . . . . . . . . . . . 183 18.5 thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 18.6 5v dc electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . 184 18.7 5v control timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 18.8 5v oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 186 18.9 3v dc electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . 187 18.10 3v control timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 18.11 3v oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 189 18.12 typical supply currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 18.13 adc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 18.2 introduction this section contains electrical and timing specifications. electrical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 182 electrical specifications motorola 18.3 absolute maximum ratings maximum ratings are the extreme limits to which the mcu can be exposed without permanently damaging it. note: this device is not guaranteed to operate properly at the maximum ratings. refer to sections 18.6 and 18.9 for guaranteed operating conditions. note: this device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum-rated voltages to this high-impedance circuit. for proper operation, it is recommended that v in and v out be constrained to the range v ss (v in or v out ) v dd . reliability of operation is enhanced if unused inputs are connected to an appropriate logic voltage level (for example, either v ss or v dd .) table 18-1. absolute maximum ratings (1) characteristic symbol value unit supply voltage v dd 0.3 to +6.0 v input voltage v in v ss 0.3 to v dd +0.3 v mode entry voltage, i rq1 pin v dd +v hi v ss 0.3 to +8.5 v maximum current per pin excluding v dd and v ss i 25 ma storage temperature t stg 55 to +150 c maximum current out of v ss i mvss 100 ma maximum current into v dd i mvdd 100 ma note: 1. voltages referenced to v ss . electrical specifications functional operating range mc68h(r)c08jl3 ? rev. 4 technical data motorola electrical specifications 183 18.4 functional operating range 18.5 thermal characteristics table 18-2. operating range characteristic symbol value unit operating temperature range t a 40 to +125 40 to +85 c operating voltage range v dd 5v 1 0% 3v 10% v table 18-3. thermal characteristics characteristic symbol value unit thermal resistance 20-pin pdip 20-pin soic 28-pin pdip 28-pin soic q ja 70 70 70 70 c/w c/w c/w c/w i/o pin power dissipation p i/o user determined w power dissipation (1) p d p d = (i dd v dd ) + p i/o = k/(t j + 273 c) w constant (2) k p d x (t a + 273 c ) + p d 2 q ja w/ c average junction temperature t j t a + (p d q ja ) c maximum junction temperature t jm 100 c notes: 1. power dissipation is a function of temperature. 2. k constant unique to the device. k can be determined for a known t a and measured p d. with this value of k, p d and t j can be determined for any value of t a . electrical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 184 electrical specifications motorola 18.6 5v dc electrical characteristics table 18-4. dc electrical characteristics (5v) characteristic (1) symbol min typ (2) max unit output high voltage (i load = ?.0ma) pta0?ta6, ptb0?tb7, ptd0?td7 v oh v dd 0.8 v output low voltage (i load = 1.6ma) pta6, ptb0?tb7, ptd0, ptd1, ptd4, ptd5 v ol 0.4 v output low voltage (i load = 25ma) ptd6, ptd7 v ol 0.5 v led drives (v ol = 3v) pta0?ta5, ptd2, ptd3, ptd6, ptd7 i ol 10 19 25 ma input high voltage pta0?ta6, ptb0?tb7, ptd0?td7, r st , irq 1 , osc1 v ih 0.7 v dd v dd v input low voltage pta0?ta6, ptb0?tb7, ptd0?td7, rst , irq 1 , osc1 v il v ss 0.3 v dd v v dd supply current run, f op = 4mhz (3) wait (mc68hrc08xxx) (4) wait (mc68hc08xxx) (4) stop (5) 40 c to 85 c i dd 10 1 5 1 12 1.5 5.5 5 ma ma ma m a digital i/o ports hi-z leakage current i il 10 m a input current i in 1 m a capacitance ports (as input or output) c out c in 12 8 pf por rearm voltage (6) v por 0 100 mv por rise time ramp rate (7) r por 0.035 v/ms monitor mode entry voltage v dd +v hi 1.5 v dd 8.5 v pullup resistors (8) ptd6, ptd7 rst , irq1 , pta0?ta6 r pu1 r pu2 1.8 16 3.3 26 4.8 36 k w k w lvi reset voltage v lvr5 3.6 4.0 4.4 v electrical specifications 5v control timing mc68h(r)c08jl3 ? rev. 4 technical data motorola electrical specifications 185 18.7 5v control timing notes: 1. v dd = 4.5 to 5.5 vdc, v ss = 0 vdc, t a = t l to t h , unless otherwise noted. 2. typical values reflect average measurements at midpoint of voltage range, 25 c only. 3. run (operating) i dd measured using external square wave clock source. all inputs 0.2 v from rail. no dc loads. less than 100 pf on all outputs. c l = 20 pf on osc2. all ports configured as inputs. osc2 capacitance linearly affects run i dd . measured with all modules enabled. 4. wait i dd measured using external square wave clock source (f op = 4mhz); all inputs 0.2 v from rail; no dc loads; less than 100 pf on all outputs. c l = 20 pf on osc2; all ports configured as inputs; osc2 capacitance linearly af- fects wait i dd . 5. stop i dd measured with osc1 grounded, no port pins sourcing current. lvi is disabled. 6. maximum is highest voltage that por is guaranteed. 7. if minimum v dd is not reached before the internal por reset is released, rst must be driven low externally until minimum v dd is reached. 8. r pu1 and r pu2 are measured at v dd = 5.0v table 18-5. control timing (5v) characteristic (1) notes: 1. v dd = 4.5 to 5.5 vdc, v ss = 0 vdc, t a = t l to t h ; timing shown with respect to 20% v dd and 70% v ss , unless otherwise noted. symbol min max unit internal operating frequency (2) 2. some modules may require a minimum frequency greater than dc for proper operation; see appropriate table for this in- formation. f op 8 mhz rst input pulse width low (3) 3. minimum pulse width reset is guaranteed to be recognized. it is possible for a smaller pulse width to cause a reset. t irl 750 ns table 18-4. dc electrical characteristics (5v) characteristic (1) symbol min typ (2) max unit electrical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 186 electrical specifications motorola 18.8 5v oscillator characteristics figure 18-1. rc vs. frequency (5v @25 c) table 18-6. oscillator component speci?ations (5v) characteristic symbol min typ max unit crystal frequency, xtalclk f oscxclk 10 32 mhz rc oscillator frequency, rcclk f rcclk 2 10 12 mhz external clock reference frequency (1) f oscxclk dc 32 mhz crystal load capacitance (2) c l crystal ?ed capacitance (2) c 1 2 c l crystal tuning capacitance (2) c 2 2 c l feedback bias resistor r b 10 m w series resistor (2), (3) r s rc oscillator external r r ext see figure 18-1 rc oscillator external c c ext ?0 pf notes: 1. no more than 10% duty cycle deviation from 50% 2. consult crystal vendor data sheet 3. not required for high frequency crystals 0 0 1020304050 14 12 10 8 6 4 2 resistor, r ext (k w ) rc frequency, f rcclk (mhz) c ext = 10 pf 5v @ 25 c r ext c ext osc1 v dd mcu electrical specifications 3v dc electrical characteristics mc68h(r)c08jl3 ? rev. 4 technical data motorola electrical specifications 187 18.9 3v dc electrical characteristics table 18-7. dc electrical characteristics (3v) characteristic (1) symbol min typ (2) max unit output high voltage (i load = ?.0ma) pta0?ta6, ptb0?tb7, ptd0?td7 v oh v dd 0.4 v output low voltage (i load = 0.8ma) pta6, ptb0?tb7, ptd0, ptd1, ptd4, ptd5 v ol 0.4 v output low voltage (i load = 20ma) ptd6, ptd7 v ol 0.5 v led drives (v ol = 1.8v) pta0?ta5, ptd2, ptd3, ptd6, ptd7 i ol 4 9 12 ma input high voltage pta0?ta6, ptb0?tb7, ptd0?td7, rst , irq 1 , osc1 v ih 0.7 v dd v dd v input low voltage pta0?ta6, ptb0?tb7, ptd0?td7, rst , irq 1 , osc1 v il v ss 0.3 v dd v v dd supply current run, f op = 2mhz (3) wait (mc68hrc08xxx) (4) wait (mc68hc08xxx) (4) stop (5) 40 c to 85 c i dd 5 1 4 1 8 1.3 4.5 5 ma ma ma m a digital i/o ports hi-z leakage current i il 10 m a input current i in 1 m a capacitance ports (as input or output) c out c in 12 8 pf por rearm voltage (6) v por 0 100 mv por rise time ramp rate (7) r por 0.035 v/ms monitor mode entry voltage v dd +v hi 1.5 v dd 8.5 v pullup resistors (8) ptd6, ptd7 rst , irq1 , pta0?ta6 r pu1 r pu2 1.8 16 3.3 26 4.8 36 k w k w lvi reset voltage v lvr3 2.0 2.4 2.69 v electrical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 188 electrical specifications motorola 18.10 3v control timing notes: 1. v dd = 2.7 to 3.3 vdc, v ss = 0 vdc, t a = t l to t h , unless otherwise noted. 2. typical values reflect average measurements at midpoint of voltage range, 25 c only. 3. run (operating) i dd measured using external square wave clock source. all inputs 0.2 v from rail. no dc loads. less than 100 pf on all outputs. c l = 20 pf on osc2. all ports configured as inputs. osc2 capacitance linearly affects run i dd . measured with all modules enabled. 4. wait i dd measured using external square wave clock source (f op = 4mhz); all inputs 0.2 v from rail; no dc loads; less than 100 pf on all outputs. c l = 20 pf on osc2; all ports configured as inputs; osc2 capacitance linearly af- fects wait i dd . 5. stop i dd measured with osc1 grounded, no port pins sourcing current. lvi is disabled. 6. maximum is highest voltage that por is guaranteed. 7. if minimum v dd is not reached before the internal por reset is released, rst must be driven low externally until minimum v dd is reached. 8. r pu1 and r pu2 are measured at v dd = 5.0v table 18-8. control timing (3v) characteristic (1) notes: 1. v dd = 2.7 to 3.3 vdc, v ss = 0 vdc, t a = t l to t h ; timing shown with respect to 20% v dd and 70% v dd , unless otherwise noted. symbol min max unit internal operating frequency (2) 2. some modules may require a minimum frequency greater than dc for proper operation; see appropriate table for this in- formation. f op 4 mhz rst input pulse width low (3) 3. minimum pulse width reset is guaranteed to be recognized. it is possible for a smaller pulse width to cause a reset. t irl 1.5 m s table 18-7. dc electrical characteristics (3v) characteristic (1) symbol min typ (2) max unit electrical specifications 3v oscillator characteristics mc68h(r)c08jl3 ? rev. 4 technical data motorola electrical specifications 189 18.11 3v oscillator characteristics figure 18-2. rc vs. frequency (3v @25 c) table 18-9. oscillator component speci?ations (3v) characteristic symbol min typ max unit crystal frequency, xtalclk f oscxclk 8 16 mhz rc oscillator frequency, rcclk f rcclk 2 8 12 mhz external clock reference frequency (1) f oscxclk dc 16 mhz crystal load capacitance (2) c l crystal ?ed capacitance (2) c 1 2 c l crystal tuning capacitance (2) c 2 2 c l feedback bias resistor r b 10 m w series resistor (2), (3) r s rc oscillator external r r ext see figure 18-2 rc oscillator external c c ext ?0 pf notes: 1. no more than 10% duty cycle deviation from 50% 2. consult crystal vendor data sheet 3. not required for high frequency crystals 0 0 1020304050 14 12 10 8 6 4 2 resistor, r ext (k w ) rc frequency, f rcclk (mhz) c ext = 10 pf 3v @ 25 c r ext c ext osc1 v dd mcu electrical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 190 electrical specifications motorola 18.12 typical supply currents figure 18-3. typical operating i dd , with all modules turned on (25 c) figure 18-4. typical wait mode i dd , with adc turned on (25 c) figure 18-5. typical stop mode i dd , with all modules disabled (25 c) 0 2 4 6 8 10 12 0123456789 5.5 v 3.3 v f op or f bus (mhz) i dd (ma) 14 mc68hrc08xxx 0 0.25 0.5 0.75 1 1.25 1.50 1.75 2 01 23 456 78 5.5 v 3.3 v i dd (ma) f op or f bus (mhz) mc68hrc08xxx 0 0.1 0.2 0.3 0.4 0.5 01 234 567 89 5.5 v 3.3 v f op or f bus (mhz) i dd ( m a) mc68hrc08xxx electrical specifications adc characteristics mc68h(r)c08jl3 ? rev. 4 technical data motorola electrical specifications 191 18.13 adc characteristics table 18-10. adc characteristics characteristic symbol min max unit comments supply voltage v ddad 2.7 (v dd min) 5.5 (v dd max) v input voltages v adin v ss v dd v resolution b ad 8 8 bits absolute accuracy a ad 0.5 1.5 lsb includes quantization adc internal clock f adic 0.5 1.048 mhz t aic = 1/f adic , tested only at 1 mhz conversion range r ad v ss v dd v power-up time t adpu 16 t aic cycles conversion time t adc 16 17 t aic cycles sample time (1) notes: 1. source impedances greater than 10 k w adversely affect internal rc charging time during input sampling. t ads 5 t aic cycles zero input reading (2) 2. zero-input/full-scale reading requires sufficient decoupling measures for accurate conversions. z adi 00 01 hex v in = v ss full-scale reading (3) f adi fe ff hex v in = v dd input capacitance c adi (20) 8 pf not tested input leakage (3) port b/port d 3. the external system error caused by input leakage current is approximately equal to the product of r source and input current. 1 m a electrical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 192 electrical specifications motorola mc68h(r)c08jl3 ? rev. 4 technical data motorola mechanical specifications 193 technical data ?mc68h(r)c08jl3 section 19. mechanical specifications 19.1 contents 19.2 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 19.3 20-pin pdip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 19.4 20-pin soic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 19.5 28-pin pdip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 19.6 28-pin soic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 19.2 introduction this section gives the dimensions for: 20-pin plastic dual in-line package (case #738) 20-pin small outline integrated circuit package (case #751d) 28-pin plastic dual in-line package (case #710) 28-pin small outline integrated circuit package (case #751f) the following figures show the latest package drawings at the time of this publication. to make sure that you have the latest package specifications, contact one of the following: local motorola sales office motorola mfax phone 602-244-6609 email rmfax0@email.sps.mot.com worldwide web (wwweb) at http://motorola.com/sps follow mfax or worldwide web on-line instructions to retrieve the current mechanical specifications. mechanical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 194 mechanical specifications motorola 19.3 20-pin pdip figure 19-1. 20-pin pdip (case #738) 19.4 20-pin soic figure 19-2. 20-pin soic (case #751d) notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of lead when formed parallel. 4. dimension b does not include mold flash. m l j 20 pl m b m 0.25 (0.010) t dim min max min max millimeters inches a 25.66 27.17 1.010 1.070 b 6.10 6.60 0.240 0.260 c 3.81 4.57 0.150 0.180 d 0.39 0.55 0.015 0.022 g 2.54 bsc 0.100 bsc j 0.21 0.38 0.008 0.015 k 2.80 3.55 0.110 0.140 l 7.62 bsc 0.300 bsc m 0 15 0 15 n 0.51 1.01 0.020 0.040 e 1.27 1.77 0.050 0.070 1 11 10 20 a seating plane k n f g d 20 pl t m a m 0.25 (0.010) t e b c f 1.27 bsc 0.050 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.150 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.13 (0.005) total in excess of d dimension at maximum material condition. a b 20 1 11 10 s a m 0.010 (0.25) b s t d 20x m b m 0.010 (0.25) p 10x j f g 18x k c t seating plane m r x 45 dim min max min max inches millimeters a 12.65 12.95 0.499 0.510 b 7.40 7.60 0.292 0.299 c 2.35 2.65 0.093 0.104 d 0.35 0.49 0.014 0.019 f 0.50 0.90 0.020 0.035 g 1.27 bsc 0.050 bsc j 0.25 0.32 0.010 0.012 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 10.05 10.55 0.395 0.415 r 0.25 0.75 0.010 0.029 mechanical specifications 28-pin pdip mc68h(r)c08jl3 ? rev. 4 technical data motorola mechanical specifications 195 19.5 28-pin pdip figure 19-3. 28-pin pdip (case #710) 19.6 28-pin soic figure 19-4. 28-pin soic (case #751f) notes: 1. positional tolerance of leads (d), shall be within 0.25 (0.010) at maximum material condition, in relation to seating plane and each other. 2. dimension l to center of leads when formed parallel. 3. dimension b does not include mold flash. 1 seating plane 15 14 28 m a b k c n f g d h j l dim min max min max inches millimeters a 36.45 37.21 1.435 1.465 b 13.72 14.22 0.540 0.560 c 3.94 5.08 0.155 0.200 d 0.36 0.56 0.014 0.022 f 1.02 1.52 0.040 0.060 g 2.54 bsc 0.100 bsc h 1.65 2.16 0.065 0.085 j 0.20 0.38 0.008 0.015 k 2.92 3.43 0.115 0.135 l 15.24 bsc 0.600 bsc m 0 15 0 15 n 0.51 1.02 0.020 0.040 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.13 (0.005) total in excess of d dimension at maximum material condition. j k f 1 15 14 28 -a- -b- 28x 14x d p s a m 0.010 (0.25) b s t m 0.010 (0.25) b m 26x g -t- seating plane c x 45 r m dim min max min max inches millimeters a 17.80 18.05 0.701 0.711 b 7.40 7.60 0.292 0.299 c 2.35 2.65 0.093 0.104 d 0.35 0.49 0.014 0.019 f 0.41 0.90 0.016 0.035 g 1.27 bsc 0.050 bsc j 0.23 0.32 0.009 0.013 k 0.13 0.29 0.005 0.011 m p 10.01 10.55 0.395 0.415 r 0.25 0.75 0.010 0.029 0 0 8 8 mechanical speci?ations technical data mc68h(r)c08jl3 ? rev. 4 196 mechanical specifications motorola motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty, represe ntation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application o r use of any product or circuit, and speci?ally disclaims any and all liability, including without limitation consequential or incidental damages. "typical" parameters which may be provided in motorola data sheets and/or speci?ations can and do vary in different applications and actual performance may vary over time. all operating parameters, i ncluding "typicals" must be validated for each customer application by customer's technical experts. motorola does not convey any license under its patent rights nor th e rights of others. motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applic ations intended to support or sustain life, or for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur. should buyer purchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its of?ers, employees, subsidiaries, af?iates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly o r indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that motorola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/af?mative action employer. 68hc908jk3 product summary page search advanced | parametric | part number | faq select country motorola home | semiconductors home | contact us semiconductors products | design support | register | login motorola > semiconductors > 68hc908jk3 : microcontroller the mc68hc08jk3 is a member of the low-cost, high-performance m68hc08 family of 8-bit microcontroller units (mcus). all mcus in the family use the enhanced m68hc08 central processor unit (cpu08) and are available with a variety of modules, memory sizes and types, and package types. block diagram 68hc908jk3 features l high-performance m68hc08 architecture l fully upward-compatible object code with m6805, m146805, and m68hc05 families l low-power design (fully static with stop and wait modes) l 5v nominal operating voltage l 3v low-power operating voltage l up to 8mhz internal bus operation l rc-oscillator circuit or crystal-oscillator options l 4096 bytes of user flash or rom l 960 bytes of monitor or self-check rom l 128 bytes of on-chip random access memory (ram) l 10 channel 8-bit adc return to top page contents: features documentation reference designs tools rich media orderable parts related links other info: faqs 3rd party design help training 3rd party tool vendors rate this page -- - 0 + ++ care to comment? 68hc908jk3 documentation documentation application note id name vendor id format size k rev # date last modified order availability an-hk-33 in-circuit programming of flash memory in the mc68hc908jl3 motorola pdf 0 1 3/27/2000 an1050_d designing for electromagnetic compatibility (emc) with hcmos microcontrollers motorola pdf 82 0 1/01/2000 - an1218/d hc05 to hc08 optimization motorola pdf 347 2 1/01/1993 an1219/d m68hc08 integer math routines motorola pdf 177 1 1/01/1997 an1219sw software files for an1219 zipped motorola zip 77 0 1/01/1995 - an1221/d hamming error control coding techniques with the hc08 mcu motorola pdf 63 0 1/01/1993 an1221sw software files for an1221 zipped motorola zip 55 0 1/01/1995 - file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (1 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page an1222/d arithmetic waveform synthesis with the hc05/08 mcus motorola pdf 24 0 1/01/1993 an1222sw software files for an1222 zipped motorola zip 20 0 1/01/1995 - an1259/d system design and layout techniques for noise reduction in mcu-based systems motorola pdf 78 0 1/01/1995 an1263/d designing for electromagnetic compatibility with single- chip microcontrollers motorola pdf 104 0 1/01/1995 an1516/d liquid level control using a motorola pressure sensor motorola pdf 77 2 1/24/2003 an1705/d noise reduction techniques for microcontroller-based systems motorola pdf 67 0 1/01/1999 an1744/d resetting microcontrollers during power transitions motorola pdf 80 0 1/01/1998 an1752/d data structures for 8-bit microcontrollers motorola pdf 213 1 5/07/2001 an1771/d precision sine-wave tone synthesis using 8-bit mcus motorola pdf 250 0 1/01/1998 an1775/d expanding digital input with an a/d converter motorola pdf 86 1 1/01/1998 an1783/d determining mcu oscillator start-up parameters motorola pdf 48 1 1/01/1999 an1818/d software sci routines with the 16-bit timer module motorola pdf 84 0 1/01/1999 an1820/d software i2c communications motorola pdf 55 0 1/01/1999 an1820sw software files for an1820 zipped motorola zip 2 0 1/01/1998 - an1831/d using mc68hc908 on-chip flash programming routines rom-resident routines in the mc68hc908gr8, mc68hc908kx8, mc68hc908jl3, mc68hc908jk3, and the mc68hc908jb8 motorola pdf 314 2 9/27/2001 an1837/d non-volatile memory technology overview motorola pdf 116 0 3/27/2000 an1853/d embedding microcontrollers in domestic refrigeration appliances motorola pdf 221 0 6/22/2000 an2093/d creating efficient c code for the mc68hc08 motorola pdf 36 0 1/01/2000 an2103/d local interconnect network (lin) demonstration motorola pdf 953 0 12/01/2000 an2120/d connecting an m68hc08 family microcontroller to an internet service provider (isp) using the point-to-point protocol (ppp) motorola pdf 741 0 5/20/2001 an2120sw software for an2120, zip format motorola zip 31 1.0 7/31/2002 - an2149/d compressor induction motor stall and rotation detection using microcontrollers motorola pdf 127 0 5/30/2001 an2158/d designing with the mc68hc908jl/jk microcontroller family motorola pdf 374 0 11/20/2001 an2159/d digital direct current ignition system using hc08 microcontrollers motorola pdf 129 0 11/20/2001 an2159sw an2159sw motorola zip 182 1 3/08/2002 - an2295 developer's serial bootloader for m68hc08 motorola pdf 738 4 10/29/2003 an2295sw software for an2295 motorola zip 725 4.0 10/21/2003 - file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (2 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page an2321/d designing for board level electromagnetic compatibility motorola pdf 1628 0 8/15/2002 an2342 opto isolation circuits for in circuit debugging of 68hc9(s)12 and 68hc908 microcontrollers motorola pdf 155 0 9/25/2002 an2438/d adc definitions and specifications motorola pdf 297 0 2/21/2003 an2504 on-chip flash programming api for codewarrior motorola pdf 530 0 10/15/2003 an2504sw software files for application note an2504 motorola zip 59 0 10/21/2003 - brochure id name vendor id format size k rev # date last modified order availability br1785/d 68hc908jl/jk family brochure motorola pdf 118 0 8/06/2001 br1822 embedded flash mcu overview motorola pdf 174 - - br68hc08famam/d 68hc08 family: high performance and flexibility motorola pdf 57 2 5/21/2003 flyrembedflash/d embedded flash: changing the technology world for the better motorola pdf 68 2 5/21/2003 data sheets id name vendor id format size k rev # date last modified order availability mc68hc08jl3/d 68hc08jl3, 68hrc08jl3, 68hc08jk3, 68hrc08jk3, 68hc08jk1, 68hrc08jk1 advance information motorola pdf 2007 4 3/27/2000 - mc68hc908jl3/h mc68h(r)c908jk1/mc68h(r)c908jk3/mc68h(r)c908jl3 technical data motorola pdf 580 1 1/10/1999 mc68hc908jl3e/d mc68h(r)c908jl3e/ mc68h(r)c908jk3e/ mc68h(r)c908jk1e technical data motorola pdf 1549 2 12/02/2002 engineering bulletin id name vendor id format size k rev # date last modified order availability eb349/d ram data retention considerations for motorola microcontrollers motorola pdf 45 1 6/22/2000 eb367/d in-circuit programming of flash memory using the monitor mode for the mc68hc908jl/jk motorola pdf 316 0 10/13/2000 eb389/d tof consideration when measuring a long input capture event motorola pdf 55 1 4/15/2002 eb390/d porting the an2120/d udp/ip code to the avnet evaluation board motorola pdf 1501 0 5/09/2002 eb396/d use of osc2/xtal as a clock output on motorola microcontrollers motorola pdf 49 0 6/19/2002 eb398 techniques to protect mcu applications against malfunction due to code run-away motorola pdf 0 0 8/13/2002 eb608/d interrupt handling considerations when modifying eeprom on hc08 microcontrollers motorola pdf 96 0 8/14/2002 errata - click here for important errata information id name vendor id format size k rev # date last modified order availability mse908jk3_2j88y/d mask set errata for mc68hc908jk3 mask 2j88y motorola pdf 60 0 12/13/2002 - file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (3 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page fact sheets id name vendor id format size k rev # date last modified order availability 68hc908jk-jlpb/d 8-bit microcontroller motorola pdf 62 1 4/03/2002 cwdevstudfacthc08 development studio motorola pdf 48 2 5/13/2002 - product change notices id name vendor id format size k rev # date last modified order availability pcn8299 add fab site for 908jl3e/jk3e/jk1e motorola htm 6 0 12/04/2002 - reference manual id name vendor id format size k rev # date last modified order availability adcrm/ad analog-to-digital reference manual motorola pdf 231 0 1/01/1996 cpu08rm/ad cpu08rm central processor unit reference manual motorola pdf 2666 3 4/03/2002 drm001/d passive infrared (pir) intruder detection using the mc68hc908jk1/3, incorporating remote control adjustment using the mc68hc908gp32 motorola pdf 2504 0 2/20/2001 drm002/d usb08 universal serial bus evaluation board using the mc68hc908jb8 designer reference manual motorola pdf 1845 0 4/12/2001 drm011/d direct current ignition reference design designer reference manual motorola pdf 379 0 5/30/2003 tim08rm/ad tim08 timer interface module reference manual motorola pdf 771 1.0 1/10/1996 selector guide id name vendor id format size k rev # date last modified order availability sg1002 analog selector guide - quarter 4, 2003 motorola pdf 579 0 10/24/2003 sg1006 microcontrollers selector guide - quarter 4, 2003 motorola pdf 826 0 10/24/2003 sg1010 sensors selector guide - quarter 4, 2003 motorola pdf 219 0 10/24/2003 sg1011 software and development tools selector guide - quarter 4, 2003 motorola pdf 287 0 10/24/2003 sg2000cr application selector guide index and cross-reference. motorola pdf 95 3 11/11/2003 sg2036 application summary home appliances - cooking products. microcontrollers provide intelligent management programs delivering high precision control over the cooking process. motorola pdf 0 1 12/16/2002 sg2037 application selector guide - home appliances dishwashers motorola pdf 0 2 6/17/2003 sg2038 application summary - home appliances - refrigerators and freezers. microcontrollers maximize appliance efficiency while supporting a variety of features in refrigerators and freezers. motorola pdf 0 1 12/16/2002 sg2039 application selector guide - vacuum cleaners vacuum cleaners motorola pdf 0 0 6/17/2003 sg2040 application selector guide - home applicances washing machines motorola pdf 0 2 6/17/2003 file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (4 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page sg2044 application summary - home appliances. dryers. new dryer features make this application more energy efficient and better able to meet consumer demands for improved control. motorola pdf 0 1 12/16/2002 users guide id name vendor id format size k rev # date last modified order availability cdswhc08qs codewarrior? development studio for 68hc08 quick start guide motorola pdf 2847 2.1 9/20/2002 - return to top 68hc908jk3 reference designs reference designs id name vendor id format size k rev # order availability rd68hc08pir passive infra red (pir) for security peripherals and other remote networks motorola - - - - return to top 68hc908jk3 tools hardware tools emulators/probes/wigglers id name vendor id format size k rev # order availability ic10000 ic1000 poweremulator isys - - - - ic20000 ic2000 poweremulator isys - - - - ic40000 ic4000 activeemulator isys - - - - indart-hc08/d in-circuit, real-time debugger/programmer for motorola 68hc08 family (usb) softec - - - - evaluation/development boards and systems id name vendor id format size k rev # order availability kitmmds08jl modular development system (mmds) kits motorola - - - kitmmevs08jl modular evaluation system (mmevs) motorola - - - m68cbl05c low-noise flex cable motorola - - - m68ics08jljk m68ics08jljk development tool kit motorola - - - m68eml08jljk emulation module motorola - - - m68cyclone08 mon08 cyclone metrowerks - - - m68multilink08 mon08 multilink metrowerks - - - oztec-08 starter kit oztec-08 starter kit oztech - - - - file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (5 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page programmers id name vendor id format size k rev # order availability mp8011a gang programmer base unit softec - - - - ap520 automated programming system sysgen - - - - powerlab universal programmer sysgen - - - - t9600 high-speed universal gang programmer sysgen - - - - software application software code examples id name vendor id format size k rev # order availability hc08delaysw hc08 software example: subroutine that delays for a whole number of milliseconds motorola zip 2 - - hc08exsw hc08 software example: library containing software examples in assembly for 68hc08 motorola zip 14 - - operating systems id name vendor id format size k rev # order availability cmx-tiny+ cmx-tiny+ cmx - - - - software tools assemblers id name vendor id format size k rev # order availability adx-08 adx-08 macro assembler-linker and ide avocet - - - - ax6808 ax6808 relocatable and absolute macro assembler for hc08 and hcs08 cosmic - - - - compilers id name vendor id format size k rev # order availability cx6808s cx6808 c cross compiler for hc08 and hcs08 cosmic - - - - icc08 icc08 v6 std image - - - - debuggers id name vendor id format size k rev # order availability zap 6808 mon08 zap 6808 mon08 debugger and flash programmer zap 6808 mon08 debugger uses the 68hc08?s on-chip monitor interface to provide a real-time ansi c and assembly source level debugger including flash programming, flash security and hardware breakpoint support. motorola - - - - zap 6808 mmds zap 6808 mmds debugger cosmic - - - - zap 6808 sim zap 6808 simulator debugger cosmic - - - - noice08 noice08 image - - - - file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (6 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page ide (integrated development environment) id name vendor id format size k rev # order availability cdcwsehc08 codewarrior development studio? for hc(s)08 special edition metrowerks - - - - cwhc08pro codewarrior development studio for motorola hc08 microcontrollers professional edition metrowerks - - - cwhc08std codewarrior development studio for motorola hc08 microcontrollers standard edition metrowerks - - - cx6808lt4 hc08 development tool suite 4k lite (free) cosmic - - - - idea08 idea08 integrated development environment for hc08 and hcs08 cosmic - - - - ic-sw-opr winidea isys - - - - return to top rich media rich media webcast id name vendor id format size k rev # order availability rmwc_codewarrior codewarrior development tools for 68hc08 and hcs12 microcontrollers. listen to our webcast for an overview of some of the challenges that developers face and an explanation of the codewarrior tools that help to address these challenges. motorola html 4 0.0 - rmwc_qfamily 8-bit microcontroller overview and q-family of flash microcontrollers listen to our companion webcasts to learn about motorola's recent 8-bit products and services-especially the hc08 q- family-that offer maximum design flexibility while helping you get to market fast. motorola htm 5 1.1 - return to top orderable parts information partnumber package info tape and reel life cycle description (code) budgetary price qty 1000+ ($us) additional info order availability kmc908jk3cdw soic 20w no product stable growth/maturity(3) $1.65 more kmc908jk3cp pdip 20 no product stable growth/maturity(3) $1.65 more kmc908jk3ecdw soic 20w no product stable growth/maturity(3) $2.47 more kmc908jk3ecp pdip 20 no product stable growth/maturity(3) $2.47 more KMCR908JK3CDW soic 20w no product stable growth/maturity(3) $1.65 more file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (7 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page kmcr908jk3cp pdip 20 no product stable growth/maturity(3) $1.40 more kmcr98jk3ecdw soic 20w no product stable growth/maturity(3) $2.47 more kmcr98jk3ecp pdip 20 no product stable growth/maturity(3) $2.47 more mc68hc908jk3cdw soic 20w no product stable growth/maturity(3) $1.65 more mc68hc908jk3cp pdip 20 no product stable growth/maturity(3) $1.65 more mc68hc908jk3ecdw soic 20w no product stable growth/maturity(3) $1.65 more mc68hc908jk3ecp pdip 20 no product stable growth/maturity(3) $1.65 more mc68hc908jk3emdw soic 20w no product stable growth/maturity(3) $1.81 more mc68hc908jk3emp pdip 20 no product stable growth/maturity(3) $1.25 more mc68hc908jk3mdw soic 20w no product stable growth/maturity(3) $1.81 more mc68hc908jk3mp pdip 20 no product stable growth/maturity(3) $1.81 more mc68hlc908jk3cdw soic 20w no product stable growth/maturity(3) $1.65 more mc68hlc908jk3cp pdip 20 no product stable growth/maturity(3) $1.65 more mc68hrc908jk3cdw soic 20w no product stable growth/maturity(3) $1.65 more mc68hrc908jk3cp pdip 20 no product stable growth/maturity(3) $1.65 more mc68hrc908jk3mdw soic 20w no product stable growth/maturity(3) $1.81 more mc68hrc908jk3mp pdip 20 no product stable growth/maturity(3) $1.81 more mc68hrc98jk3ecdw soic 20w no product stable growth/maturity(3) $1.65 more mc68hrc98jk3ecp pdip 20 no product stable growth/maturity(3) $1.65 more mc68hrc98jk3emdw soic 20w no product stable growth/maturity(3) $1.81 more mc68hrc98jk3emp pdip 20 no product stable growth/maturity(3) $1.81 more mchc908jk3cdwr2 soic 20w yes product stable growth/maturity(3) $1.73 more mchc908jk3mdwr2 soic 20w yes product stable growth/maturity(3) $1.90 more mchrc908jk3cdwr2 soic 20w yes product stable growth/maturity(3) $1.73 more mchrc908jk3mdwr2 soic 20w yes product stable growth/maturity(3) $1.90 more file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (8 of 9) [28-nov-03 3:20:38 pm] 68hc908jk3 product summary page note: are you looking for an obsolete orderable part? click here to check our distributors' inventory. return to top related links microcontrollers motor control sensors return to top http://www.motorola.com/ | site map | contact motorola | terms of use | privacy practices ? copyright 1994-2003 motorola, inc. all rights reserved. file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3_1.htm (9 of 9) [28-nov-03 3:20:38 pm] 68hc908jk1 product summary page search advanced | parametric | part number | faq select country motorola home | semiconductors home | contact us semiconductors products | design support | register | login motorola > semiconductors > 68hc908jk1 : microcontroller the mc68hc908jk1 is a member of the low-cost, high-performance m68hc08 family of 8-bit microcontroller units (mcus). all mcus in the family use the enhanced m68hc08 central processor unit (cpu08) and are available with a variety of modules, memory sizes and types, and package types. block diagram 68hc908jk1 features l high-performance m68hc08 architecture l fully upward-compatible object code with m6805, m146805, and m68hc05 families l low-power design (fully static with stop and wait modes) l 5v nominal operating voltage l 3v low-power operating voltage l up to 8mhz internal bus operation l rc-oscillator circuit or crystal-oscillator options l 1.5 kbytes of user flash l 960 bytes of monitor or self-check rom l 128 bytes of on-chip random access memory (ram) l 10 channel 8-bit adc return to top page contents: features documentation reference designs tools rich media orderable parts related links other info: faqs 3rd party design help training 3rd party tool vendors rate this page -- - 0 + ++ care to comment? 68hc908jk1 documentation documentation application note id name vendor id format size k rev # date last modified order availability an1050_d designing for electromagnetic compatibility (emc) with hcmos microcontrollers motorola pdf 82 0 1/01/2000 - an1218/d hc05 to hc08 optimization motorola pdf 347 2 1/01/1993 an1219/d m68hc08 integer math routines motorola pdf 177 1 1/01/1997 an1219sw software files for an1219 zipped motorola zip 77 0 1/01/1995 - an1221/d hamming error control coding techniques with the hc08 mcu motorola pdf 63 0 1/01/1993 an1221sw software files for an1221 zipped motorola zip 55 0 1/01/1995 - an1222/d arithmetic waveform synthesis with the hc05/08 mcus motorola pdf 24 0 1/01/1993 file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (1 of 8) [28-nov-03 3:20:57 pm] 68hc908jk1 product summary page an1222sw software files for an1222 zipped motorola zip 20 0 1/01/1995 - an1259/d system design and layout techniques for noise reduction in mcu-based systems motorola pdf 78 0 1/01/1995 an1263/d designing for electromagnetic compatibility with single- chip microcontrollers motorola pdf 104 0 1/01/1995 an1516/d liquid level control using a motorola pressure sensor motorola pdf 77 2 1/24/2003 an1705/d noise reduction techniques for microcontroller-based systems motorola pdf 67 0 1/01/1999 an1744/d resetting microcontrollers during power transitions motorola pdf 80 0 1/01/1998 an1752/d data structures for 8-bit microcontrollers motorola pdf 213 1 5/07/2001 an1771/d precision sine-wave tone synthesis using 8-bit mcus motorola pdf 250 0 1/01/1998 an1775/d expanding digital input with an a/d converter motorola pdf 86 1 1/01/1998 an1783/d determining mcu oscillator start-up parameters motorola pdf 48 1 1/01/1999 an1818/d software sci routines with the 16-bit timer module motorola pdf 84 0 1/01/1999 an1820/d software i2c communications motorola pdf 55 0 1/01/1999 an1820sw software files for an1820 zipped motorola zip 2 0 1/01/1998 - an1837/d non-volatile memory technology overview motorola pdf 116 0 3/27/2000 an1853/d embedding microcontrollers in domestic refrigeration appliances motorola pdf 221 0 6/22/2000 an2093/d creating efficient c code for the mc68hc08 motorola pdf 36 0 1/01/2000 an2103/d local interconnect network (lin) demonstration motorola pdf 953 0 12/01/2000 an2120/d connecting an m68hc08 family microcontroller to an internet service provider (isp) using the point-to-point protocol (ppp) motorola pdf 741 0 5/20/2001 an2120sw software for an2120, zip format motorola zip 31 1.0 7/31/2002 - an2149/d compressor induction motor stall and rotation detection using microcontrollers motorola pdf 127 0 5/30/2001 an2158/d designing with the mc68hc908jl/jk microcontroller family motorola pdf 374 0 11/20/2001 an2159/d digital direct current ignition system using hc08 microcontrollers motorola pdf 129 0 11/20/2001 an2159sw an2159sw motorola zip 182 1 3/08/2002 - an2295 developer's serial bootloader for m68hc08 motorola pdf 738 4 10/29/2003 an2295sw software for an2295 motorola zip 725 4.0 10/21/2003 - an2321/d designing for board level electromagnetic compatibility motorola pdf 1628 0 8/15/2002 an2342 opto isolation circuits for in circuit debugging of 68hc9(s)12 and 68hc908 microcontrollers motorola pdf 155 0 9/25/2002 an2438/d adc definitions and specifications motorola pdf 297 0 2/21/2003 file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (2 of 8) [28-nov-03 3:20:57 pm] 68hc908jk1 product summary page an2504 on-chip flash programming api for codewarrior motorola pdf 530 0 10/15/2003 an2504sw software files for application note an2504 motorola zip 59 0 10/21/2003 - brochure id name vendor id format size k rev # date last modified order availability br1785/d 68hc908jl/jk family brochure motorola pdf 118 0 8/06/2001 br1822 embedded flash mcu overview motorola pdf 174 - - br68hc08famam/d 68hc08 family: high performance and flexibility motorola pdf 57 2 5/21/2003 flyrembedflash/d embedded flash: changing the technology world for the better motorola pdf 68 2 5/21/2003 data sheets id name vendor id format size k rev # date last modified order availability mc68hc08jl3/d 68hc08jl3, 68hrc08jl3, 68hc08jk3, 68hrc08jk3, 68hc08jk1, 68hrc08jk1 advance information motorola pdf 2007 4 3/27/2000 - mc68hc908jl3/h mc68h(r)c908jk1/mc68h(r)c908jk3/mc68h(r)c908jl3 technical data motorola pdf 580 1 1/10/1999 mc68hc908jl3e/d mc68h(r)c908jl3e/ mc68h(r)c908jk3e/ mc68h(r)c908jk1e technical data motorola pdf 1549 2 12/02/2002 engineering bulletin id name vendor id format size k rev # date last modified order availability eb349/d ram data retention considerations for motorola microcontrollers motorola pdf 45 1 6/22/2000 eb367/d in-circuit programming of flash memory using the monitor mode for the mc68hc908jl/jk motorola pdf 316 0 10/13/2000 eb389/d tof consideration when measuring a long input capture event motorola pdf 55 1 4/15/2002 eb390/d porting the an2120/d udp/ip code to the avnet evaluation board motorola pdf 1501 0 5/09/2002 eb396/d use of osc2/xtal as a clock output on motorola microcontrollers motorola pdf 49 0 6/19/2002 eb398 techniques to protect mcu applications against malfunction due to code run-away motorola pdf 0 0 8/13/2002 eb608/d interrupt handling considerations when modifying eeprom on hc08 microcontrollers motorola pdf 96 0 8/14/2002 errata - click here for important errata information id name vendor id format size k rev # date last modified order availability mse908jk1_2j88y/d mask set errata for mc68hc908jk1 mask 2j88y motorola pdf 60 0 12/13/2002 - fact sheets id name vendor id format size k rev # date last modified order availability 68hc908jk-jlpb/d 8-bit microcontroller motorola pdf 62 1 4/03/2002 cwdevstudfacthc08 development studio motorola pdf 48 2 5/13/2002 - file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (3 of 8) [28-nov-03 3:20:57 pm] 68hc908jk1 product summary page product change notices id name vendor id format size k rev # date last modified order availability pcn8299 add fab site for 908jl3e/jk3e/jk1e motorola htm 6 0 12/04/2002 - reference manual id name vendor id format size k rev # date last modified order availability adcrm/ad analog-to-digital reference manual motorola pdf 231 0 1/01/1996 cpu08rm/ad cpu08rm central processor unit reference manual motorola pdf 2666 3 4/03/2002 drm001/d passive infrared (pir) intruder detection using the mc68hc908jk1/3, incorporating remote control adjustment using the mc68hc908gp32 motorola pdf 2504 0 2/20/2001 drm002/d usb08 universal serial bus evaluation board using the mc68hc908jb8 designer reference manual motorola pdf 1845 0 4/12/2001 tim08rm/ad tim08 timer interface module reference manual motorola pdf 771 1.0 1/10/1996 roadmap id name vendor id format size k rev # date last modified order availability 8bitmcurd 8-bit mcu family roadmap motorola pdf 30 0 9/01/2002 - selector guide id name vendor id format size k rev # date last modified order availability sg1002 analog selector guide - quarter 4, 2003 motorola pdf 579 0 10/24/2003 sg1006 microcontrollers selector guide - quarter 4, 2003 motorola pdf 826 0 10/24/2003 sg1010 sensors selector guide - quarter 4, 2003 motorola pdf 219 0 10/24/2003 sg1011 software and development tools selector guide - quarter 4, 2003 motorola pdf 287 0 10/24/2003 sg2000cr application selector guide index and cross-reference. motorola pdf 95 3 11/11/2003 sg2036 application summary home appliances - cooking products. microcontrollers provide intelligent management programs delivering high precision control over the cooking process. motorola pdf 0 1 12/16/2002 sg2037 application selector guide - home appliances dishwashers motorola pdf 0 2 6/17/2003 sg2038 application summary - home appliances - refrigerators and freezers. microcontrollers maximize appliance efficiency while supporting a variety of features in refrigerators and freezers. motorola pdf 0 1 12/16/2002 sg2039 application selector guide - vacuum cleaners vacuum cleaners motorola pdf 0 0 6/17/2003 sg2040 application selector guide - home applicances washing machines motorola pdf 0 2 6/17/2003 sg2044 application summary - home appliances. dryers. new dryer features make this application more energy efficient and better able to meet consumer demands for improved control. motorola pdf 0 1 12/16/2002 file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (4 of 8) [28-nov-03 3:20:57 pm] 68hc908jk1 product summary page users guide id name vendor id format size k rev # date last modified order availability cdswhc08qs codewarrior? development studio for 68hc08 quick start guide motorola pdf 2847 2.1 9/20/2002 - return to top 68hc908jk1 reference designs reference designs id name vendor id format size k rev # order availability rd68hc08pir passive infra red (pir) for security peripherals and other remote networks motorola - - - - return to top 68hc908jk1 tools hardware tools emulators/probes/wigglers id name vendor id format size k rev # order availability ic10000 ic1000 poweremulator isys - - - - ic20000 ic2000 poweremulator isys - - - - ic40000 ic4000 activeemulator isys - - - - indart-hc08/d in-circuit, real-time debugger/programmer for motorola 68hc08 family (usb) softec - - - - evaluation/development boards and systems id name vendor id format size k rev # order availability kitmmds08jl modular development system (mmds) kits motorola - - - kitmmevs08jl modular evaluation system (mmevs) motorola - - - m68cbl05c low-noise flex cable motorola - - - m68ics08jljk m68ics08jljk development tool kit motorola - - - m68eml08jljk emulation module motorola - - - m68cyclone08 mon08 cyclone metrowerks - - - m68multilink08 mon08 multilink metrowerks - - - oztec-08 starter kit oztec-08 starter kit oztech - - - - programmers id name vendor id format size k rev # order availability mp8011a gang programmer base unit softec - - - - powerlab universal programmer sysgen - - - - file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (5 of 8) [28-nov-03 3:20:57 pm] 68hc908jk1 product summary page software application software code examples id name vendor id format size k rev # order availability hc08delaysw hc08 software example: subroutine that delays for a whole number of milliseconds motorola zip 2 - - hc08exsw hc08 software example: library containing software examples in assembly for 68hc08 motorola zip 14 - - operating systems id name vendor id format size k rev # order availability cmx-tiny+ cmx-tiny+ cmx - - - - software tools assemblers id name vendor id format size k rev # order availability adx-08 adx-08 macro assembler-linker and ide avocet - - - - ax6808 ax6808 relocatable and absolute macro assembler for hc08 and hcs08 cosmic - - - - compilers id name vendor id format size k rev # order availability cx6808s cx6808 c cross compiler for hc08 and hcs08 cosmic - - - - icc08 icc08 v6 std image - - - - debuggers id name vendor id format size k rev # order availability zap 6808 mon08 zap 6808 mon08 debugger and flash programmer zap 6808 mon08 debugger uses the 68hc08?s on-chip monitor interface to provide a real-time ansi c and assembly source level debugger including flash programming, flash security and hardware breakpoint support. motorola - - - - zap 6808 mmds zap 6808 mmds debugger cosmic - - - - zap 6808 sim zap 6808 simulator debugger cosmic - - - - noice08 noice08 image - - - - ide (integrated development environment) id name vendor id format size k rev # order availability cdcwsehc08 codewarrior development studio? for hc(s)08 special edition metrowerks - - - - cwhc08pro codewarrior development studio for motorola hc08 microcontrollers professional edition metrowerks - - - cwhc08std codewarrior development studio for motorola hc08 microcontrollers standard edition metrowerks - - - cx6808lt4 hc08 development tool suite 4k lite (free) cosmic - - - - idea08 idea08 integrated development environment for hc08 and hcs08 cosmic - - - - ic-sw-opr winidea isys - - - - return to top file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (6 of 8) [28-nov-03 3:20:57 pm] 68hc908jk1 product summary page rich media rich media webcast id name vendor id format size k rev # order availability rmwc_codewarrior codewarrior development tools for 68hc08 and hcs12 microcontrollers. listen to our webcast for an overview of some of the challenges that developers face and an explanation of the codewarrior tools that help to address these challenges. motorola html 4 0.0 - rmwc_qfamily 8-bit microcontroller overview and q-family of flash microcontrollers listen to our companion webcasts to learn about motorola's recent 8-bit products and services-especially the hc08 q- family-that offer maximum design flexibility while helping you get to market fast. motorola htm 5 1.1 - return to top orderable parts information partnumber package info tape and reel life cycle description (code) budgetary price qty 1000+ ($us) additional info order availability mc68hc908jk1cdw soic 20w no product stable growth/maturity(3) $1.25 more mc68hc908jk1cp pdip 20 no product stable growth/maturity(3) $1.25 more mc68hc908jk1ecdw soic 20w no product stable growth/maturity(3) $1.25 more mc68hc908jk1ecp pdip 20 no product stable growth/maturity(3) $1.25 more mc68hc908jk1emdw soic 20w no product stable growth/maturity(3) $1.38 more mc68hc908jk1emp pdip 20 no product stable growth/maturity(3) $1.38 more mc68hc908jk1mdw soic 20w no product stable growth/maturity(3) $1.38 more mc68hc908jk1mp pdip 20 no product stable growth/maturity(3) $1.36 more mc68hlc908jk1cdw soic 20w no product stable growth/maturity(3) $1.25 more mc68hlc908jk1cp pdip 20 no product stable growth/maturity(3) $1.25 more mc68hrc908jk1cdw soic 20w no product stable growth/maturity(3) $1.25 more mc68hrc908jk1cp pdip 20 no product stable growth/maturity(3) $1.25 more file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (7 of 8) [28-nov-03 3:20:57 pm] 68hc908jk1 product summary page mc68hrc908jk1mdw soic 20w no product stable growth/maturity(3) $1.38 more mc68hrc908jk1mp pdip 20 no product stable growth/maturity(3) $1.38 more mc68hrc98jk1ecdw soic 20w no product stable growth/maturity(3) $1.25 more mc68hrc98jk1ecp pdip 20 no product stable growth/maturity(3) $1.25 more mc68hrc98jk1emdw soic 20w no product stable growth/maturity(3) $1.38 more mc68hrc98jk1emp pdip 20 no product stable growth/maturity(3) $1.38 more mchc908jk1cdwr2 soic 20w yes product stable growth/maturity(3) $1.33 more mchc908jk1mdwr2 soic 20w yes product stable growth/maturity(3) $1.46 more mchrc908jk1cdwr2 soic 20w yes product stable growth/maturity(3) $1.33 more mchrc908jk1mdwr2 soic 20w yes product stable growth/maturity(3) $1.46 more note: are you looking for an obsolete orderable part? click here to check our distributors' inventory. return to top related links microcontrollers motor control sensors return to top http://www.motorola.com/ | site map | contact motorola | terms of use | privacy practices ? copyright 1994-2003 motorola, inc. all rights reserved. file:///f|/imaging/bitting/cf_process/cpl/11252003/moto/mc68hc08jl3.htm (8 of 8) [28-nov-03 3:20:57 pm] |
Price & Availability of KMCR908JK3CDW
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |