1 GM9130HV 3a led driver with dimming control GM9130HV v2.02 www.gammamicro.com.tw typical application circuits description GM9130HV is the monolithic ic designed for a step-down dc/dc converte r capable of driving 3a load without an additional transistor. the input voltage range is up to 60v. its feedback voltage, v fb , is 200mv. the GM9130HV operates at a switching frequency of 52khz. the external shutdown function is controlled by a logic level on the on/off pin and then the circuit comes into the standby mode with i stby ~50 a (typ.). the on/off pin may be used for the analog dimming. as the voltage on the on/off pin is increased from 0.07v to 0.67v, the voltage on the fb pin falls from 200mv to 0. the self-protection features include a cycle-by- cycle current limit and a thermal protection. the GM9130HV is available in standard to220- 5, and to263-5 packages. besides, sop8 with heat sink and to252-5 packages are also available. however, these packages are limited to heat dissipation and the iled is suggested below 2a. features ? maximum input voltage up to 60v ? v fb : 200mv ? frequency: 52khz ? i led = 3.0a maximum ? on/off input may be used for the analog dimming ? thermal protection ? cycle by cycle current limit sw v in up to 60v GM9130HV fb l1 100 h c out 470 f 4 on/off 2 v in 5 1 c in2 0.10 f c in1 470 f r load figure 1. application for GM9130HV free datasheet http:///
2 gm 9 130 hv v 2.0 2 GM9130HV 3a led driver with dimmin g control marking information and pin configurations (top view) to-220-5 to-263-5 to-252-5 so-8 with exposed thermal pad ordering information ordering number oscillation frequency package shipping GM9130HVta5rg to263-5 800 units / reel GM9130HVtb5tg to220-5 50 units / tube GM9130HVtc5rg to252-5 2,500 units / reel GM9130HVps8rg 52khz psop8 2,500 units / reel 1. v in 2. sw 3. gnd 4. feedback 5. on/off GM9130HVg ayww 1. v in 2. sw 3. gnd 4. feedback 5. on/off g: green product a: assembly / test site code y: year ww: week GM9130HVg ayww 1. v in 2. sw 8. gnd 7. gnd 3. feedback 5. gnd 6. gnd GM9130HVg ayww 1. v in 2. sw 3. gnd 4. feedback 5. on/off 4. on/off
3 GM9130HV 3a led driver with dimming control GM9130HV v2.02 absolute maximum ratings (note 1) rating symbol value unit maximum supply voltage v in 63 v pin input voltage v on/off -0.3 to v in v feedback pin voltage v fb -0.3 to v in v minimum sw voltage v sw -0.8 v power dissipation p d internally limited - to220-5 45 to263-5 50 to252-5 70 thermal resistance psop8 ? ja 36.5* c/w storage temperature range t stg - 65 to 150 c maximum junction temperature t j + 150 c minimum eds rating (note 2) 2 kv lead temperature (soldering, 10 sec) + 260 c note 1: absolute maximum ratings indicate limi ts beyond which damage to the device may occur. * 2 square inch of fr-4, double sided, 1oz. minimum copper weight, is recommended on/off
4 gm 9 130 hv v 2.0 2 GM9130HV 3a led driver with dimmin g control recommended operating conditions rating symbol value unit maximum supply voltage v in 60 v operating temperature range t opr - 40 to 125 c block diagram internal regulator on/off switch buffer current limit thermal shut down reset 52khz oscillator 1.23v bandgap reference comparator error amplifier 0.2v on/off fb v in sw gnd
5 GM9130HV 3a led driver with dimming control GM9130HV v2.02 electrical characteristics specifications with standard type face are for t j =25c, and those with bold type apply over full operating temperature range parameter condition symbol min typ max unit 190 210 184 216 feedback voltage v fb 180 200 220 mv efficiency v in =12v, i load =3.0a 65 % 50 150 fb input current i fb 500 na 47 52 58 oscillator frequency f osc 42 63 khz 1.35 1.5 saturation voltage i sw = 3a v sat 1.7 v current limit cl 3.7 5.0 6.7 a maximum duty cycle dc max 100 % v in = 60v, v sw = 0v, v fb = 1.5v -0.3 --0.07 sw leakage current v in = 60v, v sw = -0.8v, v fb = 1.5v i lo -30 -8 ma 1.0 1.4 2.0 v th on/ff 0.8 2.2 v i ih -5 0.01 5 i il -2 -0.3 a quiescent current vfb = 1.5v i q 5.3 10 ma standby current i stby 50 200 a dimming voltage i led = 0, v in = 12v, see fig 1 v on/off 600 670 750 v note 2 led must be ensured with load current (iload) at v in min v in = 12v, i load = 350ma, on/off = 0v 5.5v< v in < 12v, i load = 350ma, on/off = 0v (note 2) v fb = 250mv, on/off = 0v threshold volta g e on/off v on/off = 2.5v input current on/off v on/off = 0v v on/off = 5v, v in = 60v 0 40 80 120 160 200 240 0 100 200 300 400 500 600 figure 2 dimming voltage vs v fb v fb (mv) v on/of (mv)
6 gm 9 130 hv v 2.0 2 GM9130HV 3a led driver with dimmin g control application notes output current (iled) d esign, refer to figure 1 the current through the led?s can be set by the formula below. i led = v fb /r load for example, if 2 ? r load is selected, with v fb = 200mv typical, then i led = 200 / 2 = 100ma power / heat consideration various i led could be obtained by different resistor val ues as mentioned above. however, taking the to263-5 as an example, the maximum power rating must be followed. t j = p ic ja + t a where p ic is the power of the ic itself, and ja is the thermal resistance (junction to ambient). for to263-5, the ja is 50c/w, the safe power will be p ic = t j ?t a / ja = (150 ? 25)/50 = 2.5w, and p ic = p in ? p led, where p in = v in i in , and p led = v out i led (v out = v f number of led)
7 GM9130HV 3a led driver with dimming control GM9130HV v2.02 package outline dimensions ? to-263-5 0.596 - 0.612 (15.14 - 15.54) (1.70) 0.067 typ 0.224 - 0.272 (5.70 - 6.90) (0.71 - 0.91) 0.028 - 0.036 (8.20 - 8.60) 0.322 - 0.339 (5.08 - 5.48) 0.200 - 0.216 0.389 - 0.408 (9.88 - 10.18) 7 3 0 - 8 (2.34 - 2.74) 0.092 - 0.108 (0.31 - 0.53) 0.012 - 0.021 (4.47 - 4.67) 0.176 - 0.184 (1.56 - 1.76) 0.061 - 0.069 0.046 - 0.054 (1.17 - 1.37) package outline dimensions ? to-220-5 0.030 - 0.040 (0.76 - 1.02) 0.057 - 0.077 (1.45 - 1.96) 0.330 - 0.350 (8.38 - 8.89) 0.240 - 0.260 (6.10 - 6.60) 0.100 - 0.120 (2.54 - 3.05) (0.38 + 0.18) (0.38 - 0.03) 0.400 + 0.015 0.400 - 0.005 0.149 - 0.153 (3.78 - 3.89) 0.175 - 0.185 (4.45 - 4.75) 0.015 + 0.007 0.015 - 0.001 (0.38 + 0.18) (0.38 - 0.03) 0.105 + 0.010 0.105 - 0.010 (2.67 + 0.25) (2.67 - 0.38) 0.525 - 0.555 (13.34 - 14.10) (13.34 - 14.10) 0.525 - 0.555 0.048 - 0.052 (1.22 - 1.32) o o
8 gm 9 130 hv v 2.0 2 GM9130HV 3a led driver with dimmin g control package outline dimensions ? to252-5 package outline dimensions ? psop 8 (0.356 - 0.508) seating plan 0.014 - 0.020 (0.406 - 0.270) 0.016 - 0.050 0.053 - 0.059 (1.346 - 1.753) (0.012 - 0.254) 0.008 - 0.010 (0.203 - 0.254) 8.0 max 0.004 - 0.010 d 0.150 - 0.157 (3.810 - 3.988) 0.050 (1.270) typ 0.095 - 0.130 (2.410 - 3.300) 0.228 - 0.244 (5.791 - 6.198) 0.189 - 0.197 (4.800 - 5.004) 0.090 (2.286) (6.350 ? 6.650) 0.250 ? 0.262 (5.200 ? 5.400) 0.205 ? 0.213 (9.500 ? 9.900) 0.374 ? 0.390 (1.27) 0.050 (0.400 ? 0.600) 0.016 ? 0.024 typ. (2.540) 1.00 typ. (2.550 ? 2.900) 0.100 ? 0.114 (0.430 ? 0.580) 0.017 ? 0.023 (1.400 ? 1.780) 0.055 ? 0.070 (0.000 ? 0.127) 0.000 ? 0.005 (5.400 ? 5.700) 0.213 ? 0.224 (2.200 ? 2.400) 0.087 ? 0.094 (0.430 ? 0.580) 0.017 ? 0.023 (3.800) 0.150 ref
9 GM9130HV 3a led driver with dimming control GM9130HV v2.02 ordering number g m 9130hv ta5 r g apm gamma micro circuit type package type ta5: to263-5 tb5: to220-5 tc5: to252-5 ps8: psop8 shipping type r:taping & reel t:tube g: green note: pb-free products: ? rohs compliant and compatible with the cu rrent require-ments of ipc/jedec j-std-020. ? suitable for use in pb-free soldering processes with 100% matte tin (sn) plating. green products: ? lead-free (rohs compliant) ? halogen free(br or cl does not exceed 900ppm by weight in homogeneous material and total of br and cl does not exceed 1500ppm by weight)
|
