spec no: dsao3292 rev no: v.3a date: may/12/2016 page: 1 of 5 approved: wynec checked: allen liu drawn: l.t.zhang erp: 1203014332 0.65x0.35mm smd chip led lamp (0.2mm height) part number: APG0603SEC-E-TT hyper-red features z 0.65mmx0.35mm smd led,0.2mm thickness. z low power consumption. z wide viewing angle. z compatible with automatic placement equipment. z package:4000pcs/reel. z moisture sensitivity level : level 2. z rohs compliant. description the hyper-red source color devices are made with al- gainp on gaas substrat e light emitting diode. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.1(0.004") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4. the device has a single mounting surface. the devi ce must be mounted according to the specifications.
spec no: dsao3292 rev no: v.3a date: may/12/2016 page: 2 of 5 approved: wynec checked: allen liu drawn: l.t.zhang erp: 1203014332 selection guide absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. relative humidity levels maintained between 40% and 60% in pr oduction area are recommended to avoid the build-up of static electricity ? ref jedec/jesd 625-a and jedec/j-std-033. symbol parameter emitting color typ. max. units test conditions peak peak wavelength hyper-red 632 nm i f =10ma d [1] dominant wavelength hyper-red 624 nm i f =10ma ? 1/2 spectral line half-width hyper-red 20 nm i f =10ma v f [2] forward voltage hyper-red 1.93 2.4 v i f =10ma i r reverse current hyper-red 10 ua v r =5v parameter values units power dissipation 48 mw dc forward current 20 ma peak forward current [1] 100 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c part no. emitting color (material) lens type iv (mcd) [2] @ 10ma v iewing angle [1] min. typ. 2 1/2 APG0603SEC-E-TT hyper-red(algalnp) water clear 45 120 *15 *40 140 notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. * luminous intensity value is traceable to cie127-2007 standards. notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to cie127-2007 standards. 4. excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradatio n or premature failure.
spec no: dsao3292 rev no: v.3a date: may/12/2016 page: 3 of 5 approved: wynec checked: allen liu drawn: l.t.zhang erp: 1203014332 hyper-red APG0603SEC-E-TT -90 -75 -60 -45 -30 -15 75 60 45 30 0 15 90 0.0 0.2 0.4 0.6 0.8 1.0 -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2 t a = 25 c spatial distribution
spec no: dsao3292 rev no: v.3a date: may/12/2016 page: 4 of 5 approved: wynec checked: allen liu drawn: l.t.zhang erp: 1203014332 APG0603SEC-E-TT reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsao3292 rev no: v.3a date: may/12/2016 page: 5 of 5 approved: wynec checked: allen liu drawn: l.t.zhang erp: 1203014332 packing & label specifications APG0603SEC-E-TT terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
