8.0 amp f ast recovery rectifiers maximum ratings and electrical chara cteristics rating 25 c ambient temperature uniess otherwies specified. single phase half wave, 60hz, resistive or inductive load.for capacitive load, derate current by 20%. type number maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current fea tures mechanical da t a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage at 8.0a maximum dc reverse current t c=25 c at rated dc blocking voltage t c=100 c maximum reverse recovery time (note 1) typical junction capacitance (note 2) 8.0 150 10.0 200 65 -65 +150 a a v pf c notes: 1. reverse recovery time test condition: if=0.5a, ir=1.0a, irr=0.25a 2. measured at 1mhz and applied reverse voltage of 4.0v d.c. * low forward voltage drop * high current capability * high reliability * high surge current capability frf801 thru frf807 1.3 vol t age range 50 to 1000 volts current 8.0 amperes * case: molded plastic * epoxy: ul 94v-0 rate flame retardant * lead: lead solderable per mil-std-202, method 208 guranteed * polarity: as marked * mounting position: any operating and storage t emperature range t j , t stg 50 100 200 400 600 800 1000 v 50 100 200 400 600 800 1000 v 35 70 140 280 420 560 700 v frf801 FRF802 frf803 frf804 frf805 frf806 frf807 units ns 250 500 150 dimensions in inches and (millimeters) + + pin 1 pin 2 case ito-220a(fully insulated) .412 .248 .122 (3.1) .189 (4.8) .158 .610 .550 .100 (2.54) .060 .035 .108 (10.5) (6.3) (4.0) (15.5) (14.0) (1.5) (0.9) (2.75) max. max. max. min. max. max. 3.4 max. hole thru f max. max. .114(2.9) .098(2.5) at tc=75 c a a 192
1 10 100 0.1 500 rating and characteristic curves (frf801 thru frf807) characteristics fig.2-typical forward current dera ting curve a v e r a g e f o r w a r d c u r r e n t , ( a ) i n s t a n t a n e o u s f o r w a r d c u r r e n t , ( a ) forward volt age,(v) pulse width 300us 1% duty cycle 12 10 8 6 4 2 (+) (+) 25vdc (approx.) ( ) ( ) pulse generator (note 2) oscilliscope (note 1) 1 non-inductive w notes: 1. rise time= 7ns max., input impedance= 1 megohm.22pf. 2. rise time= 10ns max., source impedance= 50 ohms. +0.5a 0 -0.25a -1.0a | || | | | | | 1cm set time base for 50 / 10ns / cm trr d.u.t. .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 40 single phase half wave 60hz resistive or inductive load fig.3- test circuit diagram and reverse recovery time characteristics 10 noninductive 50 noninductive w w tj=25 c fig.5-typical junction capacit ance reverse voltage,(v) j u n c t i o n c a p a c i t a n c e , ( p f ) 140 120 100 80 60 40 20 0 .01 .05 .1 .5 1 5 10 50 100 fig.4-maximum non-repetitive forward surge current 50 0 100 150 200 250 number of cycles at 60hz 1 10 5 50 100 tj=25 c 8.3ms single half sine wave jedec method 0 20 40 60 80 100 120 140 160 180 200 0 fig.1-typical forward case temperature,( c) p e a k f o r w a r d s u r g e c u r r e n t , ( a ) 193
|