? semiconductor components industries, llc, 2012 april, 2012 ? rev. 10 1 publication order number: nl27wz08/d nl27wz08 dual 2-input and gate the nl27wz08 is a high performance dual 2 ? input and gate operating from a 1.65 v to 5.5 v supply. features ? extremely high speed: t pd 2.5 ns (typical) at v cc = 5 v ? designed for 1.65 v to 5.5 v v cc operation ? over voltage tolerant inputs ? lvttl compatible ? interface capability with 5 v ttl logic with v cc = 3 v ? lvcmos compatible ? 24 ma balanced output sink and source capability ? near zero static supply current substantially reduces system power requirements ? replacement for nc7wz08 ? chip complexity: fet = 124 ? these devices are pb ? free and are rohs compliant ? nlv prefix for automotive and other applications requiring unique site and control change requirements; aec ? q100 qualified and ppap capable a1 1 a2 y2 figure 1. pinout figure 2. logic symbol & y1 a1 b2 b1 v cc b1 gnd 2 3 8 7 6 45 y2 y1 b2 a2 ieee/iec see detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ordering information marking diagram us8 us suffix case 493 8 1 http://onsemi.com 1 8 l2 m l2 = device code m = date code* = pb ? free package *date code orientation may vary depending upon manufacturing location. (note: microdot may be in either location) pin assignment pin 1 2 3 4 5 6 7 8 function a1 b1 y2 gnd a2 b2 y1 v cc inputs function table b l h l h output y l h a l l h h l l y = ab h = high logic level l = low logic level
nl27wz08 http://onsemi.com 2 maximum ratings symbol parameter value units v cc dc supply voltage ? 0.5 to +7.0 v v i dc input voltage ? 0.5 to +7.0 v v o dc output voltage ? 0.5 to v cc + 0.5 v i ik dc input diode current v i < gnd ? 50 ma i ok dc output diode current v o < gnd ? 50 ma i o dc output sink current 50 ma i cc dc supply current per supply pin 100 ma i gnd dc ground current per ground pin 100 ma t stg storage temperature range ? 65 to +150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias +150 c ja thermal resistance (note 1) 250 c/w p d power dissipation in still air at 85 c 250 mw msl moisture sensitivity level 1 f r flammability rating oxygen index: 28 to 34 ul 94 v ? 0 @ 0.125 in v esd esd withstand voltage human body model (note 2) machine model (note 3) charged device model (note 4) > 2000 > 200 n/a v i latch ? up latch ? up performance above v cc and below gnd at 85 c (note 5) 500 ma stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. measured with minimum pad spacing on an fr4 board, using 10 mm ? by ? 1 inch, 2 ? ounce copper trace with no air flow. 2. tested to eia/jesd22 ? a114 ? a. 3. tested to eia/jesd22 ? a115 ? a. 4. tested to jesd22 ? c101 ? a. 5. tested to eia/jesd78. recommended operating conditions symbol parameter min max units v cc supply voltage operating data retention only 1.65 1.5 5.5 5.5 v v i input voltage (note 6) 0 5.5 v v o output voltage (high or low state) 0 5.5 v t a operating free ? air temperature ? 55 +125 c t/ v input transition rise or fall rate v cc = 2.5 v 0.2 v v cc = 3.0 v 0.3 v v cc = 5.0 v 0.5 v 0 0 0 20 10 5 ns/v 6. unused inputs may not be left open. all inputs must be tied to a high ? or low ? logic input voltage level.
nl27wz08 http://onsemi.com 3 dc electrical characteristics symbol parameter condition v cc (v) t a = 25 c ? 55 c t a 125 c units min typ max min max v ih high ? level input voltage 1.65 2.3 to 5.5 0.75 v cc 0.7 v cc 0.75 v cc 0.7 v cc v v il low ? level input voltage 1.65 2.3 to 5.5 0.25 v cc 0.3 v cc 0.25 0.3 v cc v v oh high ? level output voltage v in = v il or v ih i oh = 100 a i oh = ? 3 ma i oh = ? 8 ma i oh = ? 12 ma i oh = ? 16 ma i oh = ? 24 ma i oh = ? 32 ma 1.65 to 5.5 165 2.3 2.7 3.0 3.0 4.5 v cc ? 0.1 1.29 1.9 2.2 2.4 2.3 3.8 v cc 1.5 2.1 2.4 2.7 2.5 4.0 v cc ? 0.1 1.5 1.9 2.2 2.4 2.3 3.8 v v ol low ? level output voltage v in = v ih or v oh i ol = 100 a i ol = 3 ma i ol = 8 ma i ol = 12 ma i ol = 16 ma i ol = 24 ma i ol = 32 ma 1.65 to 5.5 2.3 2.7 3.0 3.0 4.5 0.08 0.20 0.22 0.28 0.38 0.42 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.1 0.24 0.3 0.4 0.4 0.55 0.55 v i in input leakage current v in = 5.5 v or gnd 0 to 5.5 0.1 1.0 a i cc quiescent supply current v in = 5.5 v or gnd 5.5 1.0 10 a i off power off leakage current v in = 5.5 v or v out = 5.5 v 0 1.0 10 a ac electrical characteristics t r = t f = 3.0 ns symbol parameter condition v cc (v) t a = 25 c ? 55 c t a 125 c units min typ max min max t plh t phl propagation delay (figure 3 and 4) r l = 1 m c l = 15 pf 1.8 0.15 2.0 5.7 10.5 2.0 11.0 ns 2.5 0.2 1.0 3.5 5.8 2.0 6.2 r l = 1 m c l = 15 pf r l = 500 c l = 50 pf 3.3 0.3 0.8 1.2 2.6 3.2 3.9 4.8 0.8 1.2 4.3 5.2 r l = 1 m c l = 15 pf r l = 500 c l = 50 pf 5.0 0.5 0.5 0.8 1.9 2.5 3.1 3.7 0.5 0.8 3.3 4.0 capacitive characteristics symbol parameter condition typical units c in input capacitance v cc = 5.5 v, v i = 0 v or v cc 4 pf c pd power dissipation capacitance (note 7) 10 mhz, v cc = 3.3 v, v i = 0 v or v cc 10 mhz, v cc = 5.5 v, v i = 0 v or v cc 25 30 pf 7. c pd is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption with out load. average operating current can be obtained by the equation: i cc(opr ) = c pd v cc f in + i cc . c pd is used to determine the no ? load dynamic power consumption; p d = c pd v cc 2 f in + i cc v cc .
nl27wz08 http://onsemi.com 4 r l c l a 1 ? mhz square input wave is recommended for propagation delay tests. v cc figure 3. switching waveform figure 4. test circuit t f = 3 ns v cc gnd v oh v ol 90% 50% 10% 50% t plh t phl output y input a and b t f = 3 ns 90% 50% 10% 50% device ordering information device order number package type shipping ? nl27wz08usg us8 (pb ? free) 3000 / tape & reel NLV27WZ08USG* us8 (pb ? free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. *nlv prefix for automotive and other applications requiring unique site and control change requirements; aec ? q100 qualified and ppap capable.
nl27wz08 http://onsemi.com 5 package dimensions us8 us suffix case 493 ? 02 issue b dim a min max min max inches 1.90 2.10 0.075 0.083 millimeters b 2.20 2.40 0.087 0.094 c 0.60 0.90 0.024 0.035 d 0.17 0.25 0.007 0.010 f 0.20 0.35 0.008 0.014 g 0.50 bsc 0.020 bsc h 0.40 ref 0.016 ref j 0.10 0.18 0.004 0.007 k 0.00 0.10 0.000 0.004 l 3.00 3.20 0.118 0.126 m 0 6 0 6 n 5 10 5 10 p 0.23 0.34 0.010 0.013 r 0.23 0.33 0.009 0.013 s 0.37 0.47 0.015 0.019 u 0.60 0.80 0.024 0.031 v 0.12 bsc 0.005 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeters. 3. dimension ?a? does not include mold flash, protrusion or gate burr. mold flash. protrusion and gate burr shall not exceed 0.140 mm (0.0055?) per side. 4. dimension ?b? does not include inter ? lead flash or protrusion. inter ? lead flash and protrusion shall not e3xceed 0.140 (0.0055?) per side. 5. lead finish is solder plating with thickness of 0.0076 ? 0.0203 mm. (300 ? 800 ?). 6. all tolerance unless otherwise specified 0.0508 (0.0002 ?). l b a p g 4 1 5 8 c k d seating j s r u detail e v f h n r 0.10 typ m ? y ? ? x ? ? t ? detail e t m 0.10 (0.004) xy t 0.10 (0.004) plane mm inches scale 8:1 3.8 0.15 0.50 0.0197 1.0 0.0394 0.30 0.012 1.8 0.07 soldering footprint* *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 nl27wz08/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
