www.osram.com/flex due to the speci al conditions of manufacturing processes of led, the typical data of technical parameters can only reflect statistical figure s and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2016 - 04 - 07 01 linearlight fle x eco lf 05e2 technical datasheet key features & benefits ? ? ? ? ? possible application s ? ? ? quick reference product order code color k v w/m lm/m lm/w beam angle () shipping units lf05e2 - w2f - 824 4052899942790 white 2400 24 3.0 220 73 120 8 lf05e2 - w2f - 827 4008321971357 white 2700 24 3.6 205 57 120 8 lf05e2 - w2f - 830 4052899928435 white 3000 24 3.6 220 61 120 8 lf05e2 - w2f - 840 4052899928442 white 4000 24 3.6 240 67 120 8 lf05e2 - w2f - 865 4008321971418 white 6500 24 3.6 220 61 120 8 lf05e2 - w2f - 824 4052899942790 white 2400 24 3.0 220 73 120 8
linearlight fle x eco | lf 05e2 | technical datasheet due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2016 - 04 - 07 02 technical operating data for complete reel product order code power [w] current [a] luminous flux [lm] module length [m] lf05e2 - w2f - 824 4052899942790 30.0 1.3 2,200 10 lf05e2 - w2f - 827 4008321971357 36.0 1.5 2,050 10 lf05e2 - w2f - 830 4052899928435 36.0 1.5 2,200 10 lf05e2 - w2f - 840 4052899928442 36.0 1.5 2,400 10 lf05e2 - w2f - 865 4008321971418 36.0 1.5 2,200 10 lf05e2 - w2f - 824 4052899942790 30.0 1.3 2,200 10 technical specifications general dimmable pulse width modulation (pwm) binning fine white (3 step macadam ellipse) lifetime 5 0,000 h (l70b50, tc max) adhesive tape on backside 3m f 9460 complementary systems connectsystem, slimconnectsystem, slim track, optotronic certifications ce, u l8750 recognized , ul2108 listed , eac , rohs compliant operating conditions operating temperature at tc - point [c] - 2 0 C 75 storage temperature [c] - 2 0 C 75 voltage range [v dc] 23 C 25 reverse voltage [v dc] 25 ? exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the led module. ? exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the led module. ? the temperatur e of the led module must be measured at the tc - point according to en60598 - 1 in a thermally constant status with a temperature sensor or a temperature sensitive label. for exact location of the tc - point see drawing below. technical drawing s tc
linearlight fle x eco | lf 05e2 | technical datasheet due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2016 - 04 - 07 03 safety information ? the led module itself and all its components must not be mechanically stressed. ? assembly must not damage or destroy conducting paths on the circuit board. ? installation of led modules (with power supplies) needs to be made with regard to all app licable electrical and safety standards. only qualified personnel should be allowed to perform installations. ? observe correct polarity! depending on the product incorrect polarity will lead to emission of red or no light. the module can be destroyed! corre ct polarity immediately! ? parallel connection is highly recommended as safe electrical operation mode. serial connection is not recommended. unbalanced voltage drop can cause hazardous overload and damage the led module. ? please ensure that the power supply is of adequate power to operate the total load. ? when mounting on metallic or otherwise conductive surfaces, there needs to be an electrical isolation at soldering points between mod ule and the mounting surface. ? the maximum length of lf05e2 is 10 m with powe r feed at one end. ? pay attention to standard esd precautions when installing the module. ? the module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. the ability to customize the length of the module by cutting at specifically marked points is a key feature of the product and hence the reason for no factory installed conformal coating. for these reasons, it is recommended that the user complete all module modifications first (cutting wiring) and then a pply a conformal coating in the final stages of installation. ? damage by corrosion will not be honored as a materials defect claim. it is the users responsibility to provide suitable protection again corrosive agents such as moisture and condensation and o ther harmful elements. ? for applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. the module can be protected against condensation water by treatment with an appropriate c ircuit board grade conformal coating. the conformal coating should have the following features: o optical transparency o uv - resistance o thermal expansion matching the thermal expansion of the module o low permeability of steam for all climatic conditions o resista nce against corrosive environment. in order to drive osram led - modules safely, it is absolutely necessary to operate them with an electronically stabilized power supply protecting against short circuits, overload and overheating. to also ease the luminaire/installation approval, electronic control gear for led or led modules should carry the ce mark and be enec certified. in europe the declarations of conformity must include the following standards: ce: ec 6134 7 - 2 - 13, en 55015, iec 61547 and iec 61 000 - 3 - 2 - enec: 61347 - 2 - 13 and iec/en 62384. also check for the mark of an independent authorized certification institute. please see the relevant brochure for more detailed information (see "related and further information") osram optotronic? control gear complies with all relevant standards and guarantees safe operation. a ssembly information ? connection with soldering wires on unmounted module: do not pre - tin the solder - pads but pre - tin the wires and solder for max 4s at 300c. allow solder - points to c ompletely cool down before the next soldering. prevent shear - or peel forces. ? soldering of wires with the module mounted on a heatsink: pre - tin solder - pads and wires and solder for max 3 s at 350 c. allow solder - points to completely cool down before th e next soldering. prevent shear - or peel forces. ? the smallest unit (10 0 mm C 5 leds) can be removed by cutting with scissors between the designated solder pads. ? m ounting of the module is facilitated by the double - sided adhesive tape on the back - surface of the module. ? mounting surface must be clean and dry, free of oils or silicone coatings as well as dirt particle.
linearlight fle x eco | lf 05e2 | technical datasheet due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2016 - 04 - 07 04 ? the mounting substrate must have sufficient structural integrity. take care to completely remove the protective backing. once the module is a ppropriately positioned, pre on the module with about 20n/cm2 (refer to application techniques of 3m adhesive transfer tapes). in difficult cases the use of a prime may help. ? m ax imum te mperature ratings must be kept . t herefore the module m ay have to be mounted on a met al heat sink , depending on the individual installation. ? the minimum bending radius is 2 cm. the module may be bent over a smaller radius but only in regions of the circuit board containing electronic components and such bends should be made once and fixed in position to avoid cyclic fatigue. ? bending is only allowed within the bending axis of the pcb. bending outside of that leads to torsion which may cause damage to the module and will lead to failure. ? when installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of adequate mounting surfaces is necessary . othe rwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion. complementary systems & accessories slimconnect system description product name order code shipping details 2pin feeder lf - 2pin flex sc 4008321832436 10 / 250 jumper (board - to - board) lf - conn flex sc 4008321832467 25 / 250 extension wire 30 mm lf - wire - 30 flex sc 4008321875587 100 / 10,000 extension wire 15 0 mm lf - wire - 150 flex sc 4008321875563 50 / 5,000 connect system description product name order code shipping details 2pin feeder lf - 2pin flex 4008321955326 10 / 100 jumper (10mm extension) lf - conn - 10 flex 4008321955333 10 / 200 jumper (150mm extension) lf - conn - 150 flex 4008321955340 10 / 100 slimtrack system description product name order code shipping details slim track lf - lts - 2100 slim track 4008321978981 40 mounting bracket for slim track lf - lts - mb 4008321979025 35 / 280 clear slim track cover lf - lts cover c 4008321790187 40 diffuse slim track cover lf - lts - cover - diffuse 4008321979001 40 endcap for diffuse cover lf - lts - endcap 4008321979049 20 / 160 semi - diffuse slim track cover lf - lts cover s 4008321790200 40
linearlight fle x eco | lf 05e2 | technical datasheet due to the special conditions of manufacturing processes of led, the typical data of technical parameters can only reflect st atistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. subject to change without notice. errors and omissions excepted. version: 2016 - 04 - 07 05 optotronic recommended optotronic? drivers ean non - dimmable optotronic ot 6/200 - 240/24 ce 4008321113269 optotronic ot 8/200 - 240/24 4008321040169 optotronic ot 20/220 - 240/24 4050300618111 optotronic ot 20/120 - 240/24 s 4050300662626 optotronic ot 75/220 - 240/24 4050300817477 optotronic ot 75/220 - 240/24 e 4008321362476 optotronic ot 80/220 - 240/24 p 4008321981684 optotronic ot 120/220 - 240/24 p 4008321981707 optotronic ot 240/220 - 240/24 p 4008321981721 dimmable optotronic ot easy 60 ii 4008321187796 optotronic ot easy 80 4008321808363 optotronic ot 65/220 - 240/24 3dim e 4008321964403 optotronic oti dali 75/220 - 240/24 1 - 4 ch 4008321371560 optotronic ot 80/220 - 240/24 dim p 4008321981677 optotronic ot 120/220 - 240/24 dim p 4008321981691 optotronic ot 240/220 - 240/24 dim p 4008321981714 please consider that lengths may differ if further controls are installed. global order information europe/mea lf05e2 - w2f - 824 4052899942790 lf05e2 - w2f - 827 4008321971357 lf05e2 - w2f - 830 4052899928435 lf05e2 - w2f - 840 4052899928442 lf05e2 - w2f - 865 4008321971418 lf05e2 - w2f - 824 4052899942790 ot C 24v l a l c l b maximim length per ot: l a + l b + l c + ? l max/ot maximum length per strip: l a b c
www.osram.com/flex osram gmbh head office: marcel - breuer - strasse 6 80807 munich, germany +49 89 6213 - 0 www.osram.com sales and technical support is given by the local osram subsidiaries. on the osram website all subsidiaries are listed with complete address and phone numbers. linearlight fle x eco lf 05e2 technical datasheet 2016 - 04 - 07 related and further information ? osram led systems www.osram.com/led - systems ? osram: flexible led modules www.osram.com/flex ? osram catalogue http://catalog.osram.com ? general information www.osram.com
|
