page 1 of 3 dc/dc converters tmv-en series, 1 watt features i/o isolation voltage 3000 vacrms reinforced insulation, rated for 300 vac working voltage certifed to iec/en/ul 60950-1 safety standards safety barrier 100 % production test low coupling capacity single-in-line package (sip) lead-free design, rohs compliant 3-year product warranty the tmv-en series is a range of 1 watt non-regulated dc/dc converters with high i/o-isolation. this product features an isolation barrier which is approved for supplementary an reinforced insulation. smd construction and a special designed toroidal transformer made it possible to built these converters in a standard sip package with a very small footprint. these features making the tmv-en series an economical solution in many dc/dc converter applications requiring safety agency approval. order code input voltage output voltage output current max. effciency typ. tmv 0505 en 5 vdc 200 ma 66 % tmv 0512 en 12 vdc 80 ma 66 % tmv 0515 en 5 vdc 10 % 15 vdc 65 ma 66 % tmv 0505d en 5 vdc 100 ma 66 % tmv 0512d en 12 vdc 40 ma 72 % tmv 0515d en 15 vdc 35 ma 73 % tmv 1205 en 5 vdc 200 ma 66 % tmv 1212 en 12 vdc 80 ma 66 % tmv 1215 en 12 vdc 10 % 15 vdc 65 ma 66 % tmv 1205d en 5 vdc 100 ma 66 % tmv 1212d en 12 vdc 40 ma 74 % tmv 1215d en 15 vdc 35 ma 75 % models c b scheme u l 60950 -1 http://www.tracopower.com
page 2 of 3 all specifcations valid at nominal input voltage, full load and +25c after warm-up time unless otherwise stated. dc/dc converters tmv-en series 1 watt input specifications input current no load / full load 5 vin models: 55 ma / 285 ma typ. 12 vin models: 30 ma / 115 ma typ. surge voltage (1 s max.) 5 vin models: 9 v max. 12 vin models: 29 v max. reverse polarity input current 0.3 a max. reflected input ripple current can be reduced by ext. 1C3.3 f polyester film capacitor input filter internal capacitor input fuse recommended, required for compliance with cb C recommended fuse rating 5 v models: 500 ma 12 v models: 200 ma output specifications voltage set accuracy 1 % typ. / 3 % max. voltage balance (dual output models, balanced loads) 0.1 % typ. / 1 % max. regulation C input variation ( 1 % change of vin) 1.2 % typ. / 1.5 % max. C load variation (20 C 100 %) <10 % ripple and noise (20 mhz bandwidth) 100 mvp-p typ. / 150 mvp-p max. temperature coefficient 0.01 %/k typ. / 0.02 %/k max. short circuit protection limited 0.5 s max. capacitive load single output models: 680 f max. dual output models: 220 f max. (each output) isolation /safety isolation voltage C isolation test voltage (tested for 1 s) 4500 vpk C i/o isolation voltage (60 s) 3000 vac C rated max. working voltage 300 vac / 640 vpk isolation capacitance (input/output) 15 pf typ. / 20 pf max. isolation resistance (input/output) >10 gohm safety standards iec 60950-1:2005 +a1:2009 en 60950-1:2006 +a1:2010 +a11:2009 + a12 : 2 011 ul 60950-1, csa c22.2 no. 60950-1-03 C certification documents www.tracopower.com/overview/tmv-en general specifications temperature ranges C operating C25c to +85c C max. ambient approved iec/ul 60950-1 +70c C case temperature +90c max. C storage temperature C50c to +125c derating 2.85 %/k above 70c humidity (non condensing) 95 % rel h max. reliability, calculated mtbf (mil-hdbk-217f at +25c, ground benign) >2000000 h switching frequency 50 to 100 khz (frequency modulation) altitude during operation 4000m max. approved environmental compliance C reach www.tracopower.com/ pr oducts/reach-declaration.pdf C rohs rohs directive 2011/65/eu http://www.tracopower.com
page 3 of 3 dc/dc converters tmv-en series 1 watt physical specifications casing material non conductive plastic (ul 94v-0 rated) package weight 3.9 g ( 0.14 o z ) soldering temperature max. 260c / 10 s outline dimensions pin single dual 1 +vin (vcc) +vin (vcc) 2 Cvin (gnd) Cvin (gnd) 5 Cvout Cvout 6 no pin common 7 +vout +vout pin-out rev. december 13. 2017 bottom view 1 2 6 5 7 7.5 (0.3) 2.54 0.5 3.5 2.54 22.0 (0.87) 7.62 2.54 3.2 (0.13) 12.5 (0.49) 0.5 (0.02) (0.02) 0.5 (0.02) (0.1) (0.1) (0.1) (0.14) (0.3) 0.5 (0.02) 2.0 (0.08) 0.25 (0..01) supporting documents: www.tracopower.com/overview/tmv-en dimensions in [mm], () = inch tolerance 0.5 (0.02) pin pich tolerance 0.13 (0.005 pin width tolerance 0.05 (0.002) sp ec i?cati ons can be changed wi thout noti ce! make sure you are using the latest documentation, downloadable at www.tracopower. com www .tracopower. com
|
